2009-Mar-14 21:46:51 BEGIN executive: CIMA executive starting ... 2009-Mar-14 21:46:51 NOTE executive: STARTING NEW CIMA SESSION 2009-Mar-14 21:46:51 INFO1 executive: Using CIMA version 3.1.03 'smart' from 2009-01-20 13:50 2009-Mar-14 21:46:51 INFO4 executive: This is an ON-LINE session 2009-Mar-14 21:46:51 INFO4 executive: This is a REMOTE session 2009-Mar-14 21:46:51 INFO5 executive: All entries in the log-file are timestamped in AST ( = UTC - 4 hours ) 2009-Mar-14 21:46:51 INFO1 executive: CIMA session for project 'a2010' in 'line' mode for 'Lyle Hoffman' 2009-Mar-14 21:46:51 INFO2 executive: Logging to '/share/obs4/usr/a2010/a2010.cimalog_20090314' 2009-Mar-14 21:46:52 LOG2 log_preferences: Currently applied preferences: 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(dailylog) = daily 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(offlinelog) = skip 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(datawindow) = open 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(limitwarning) = enabled 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(wappfailure) = abort 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(helpstyle) = stay-open 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(logcolours) = full 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(displaylevel) = INFO5 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(loglevel) = LOG5 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(displayformat) = long 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(logformat) = new 2009-Mar-14 21:46:52 LOG2 log_preferences: prefs(fontsize) = 3 2009-Mar-14 21:46:52 LOG3 vw_send: To DATATAKING: source /share/obs4/usr/aoui/psriflo.tcl 2009-Mar-14 21:46:52 LOG3 vw_send: To DATATAKING: cd /share/obs4/usr/a2010 2009-Mar-14 21:46:52 ALERT executive: CIMA executive ready 2009-Mar-14 21:46:55 NOTE frontend: CIMA frontend ready 2009-Mar-14 21:46:57 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:46:57 LOG4 got_cormsg: From DATATAKING: setup 2009-Mar-14 21:47:05 COMMAND CIMA-send_to_exec: Sending command to select new receiver 2009-Mar-14 21:47:05 LOG4 exec_msg: From OBSERVER: select_receiver alfa no no yes 2009-Mar-14 21:47:05 LOG1 select_receiver: Calling 'select_receiver alfa no no yes' 2009-Mar-14 21:47:05 BEGIN begin_task: Starting task 'selecting receiver ALFA' 2009-Mar-14 21:47:05 LOG5 begin_task: Level: (1) ID = <10001> Status = 0 0 0 0 ok 2009-Mar-14 21:47:05 NOTE select_receiver: Starting to select receiver ALFA 2009-Mar-14 21:47:05 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Receiver Selection} TOTALLOOPS 1 TASKWAIT BITMAP stat_alfa_rot INFO {Selecting receiver ALFA ...} 2009-Mar-14 21:47:05 LOG3 vw_send: To DATATAKING: setupall alfa 1375.0 2009-Mar-14 21:47:05 LOG3 vw_send: To DATATAKING: acvlbical off 2009-Mar-14 21:47:05 NOTE select_receiver: Don't forget to choose a source after receiver selection! 2009-Mar-14 21:47:05 STOP finish_task: Finishing task 'selecting receiver ALFA' 2009-Mar-14 21:47:05 LOG5 finish_task: Level: (1) ID = <10001> Status = 0 0 0 0 ok 2009-Mar-14 21:47:05 DONE finish_task: DONE finished selecting: receiver ALFA 2009-Mar-14 21:47:05 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 21:47:05 END end_task: Finishing task 'selecting receiver ALFA' with status 'OK' 2009-Mar-14 21:47:06 LOG5 end_task: Level: (1) ID = <10001> Status = 0 0 0 0 ok 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: mcpSetupCmd: prg tpProg err 0x300002 2009-Mar-14 21:47:06 LOG1 got_cormsg: Start-up error message from DATATAKING: 'mcpSetupCmd: prg tpProg err 0x300002' 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: vw% io 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: tapeIo Off discIo Off gioIo Off 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: vw% tape stat 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: mcpTapeCmd: err 0xd0003 2009-Mar-14 21:47:06 LOG1 got_cormsg: Start-up error message from DATATAKING: 'mcpTapeCmd: err 0xd0003' 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: vw% connectall 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: connected : prgMgr@cor 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: connected : prgMgr@corp1 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: connected : prgMgr@pnt 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: connected : prgMgr@da 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: connected : prgMgr@dap1 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: connected : prgMgr@dap2 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: vw% online.. exit cmd to quit. 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: vw% source /share/obs4/usr/aoui/psriflo.tcl 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: cd /share/obs4/usr/a2010 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: setupall alfa 1375.0 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: acvlbical off 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: 2009-Mar-14 21:47:06 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:47:13 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:47:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:49:22 COMMAND CIMA-send_to_exec: Sending command to point to a source 2009-Mar-14 21:49:22 LOG4 exec_msg: From OBSERVER: track_new_source galfasrc 085200.0 +215400 J 0 0 main small /share/obs4/usr/a2010/a2010.cat 0 Topocentric velocity(optical) 0 0 0 0 0 2009-Mar-14 21:49:22 LOG1 track_new_source: Calling 'track_new_source galfasrc 085200.0 +215400 J 0 0 main small /share/obs4/usr/a2010/a2010.cat 0 Topocentric velocity(optical) 0 0 0 0 0' 2009-Mar-14 21:49:22 BEGIN begin_task: Starting task 'selecting new source' 2009-Mar-14 21:49:22 LOG5 begin_task: Level: (1) ID = <10002> Status = 0 0 0 0 ok 2009-Mar-14 21:49:22 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Sending Tracking Commands} SOURCE {galfasrc} INFO {Selecting source 'galfasrc' ...} 2009-Mar-14 21:49:22 LOG3 track_source: Calling 'track_source galfasrc 085200.0 +215400 J 0 0 main small /share/obs4/usr/a2010/a2010.cat 0 Topocentric velocity(optical)' 2009-Mar-14 21:49:22 START begin_task: Starting task 'sending tracking commands' 2009-Mar-14 21:49:22 LOG5 begin_task: Level: (2) ID = <10003> Status = 0 0 0 0 ok 2009-Mar-14 21:49:22 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Sending Tracking Commands} SOURCE {galfasrc} INFO {Slewing to source 'galfasrc' ...} 2009-Mar-14 21:49:22 INFO1 track_source: Starting to track galfasrc 2009-Mar-14 21:49:22 LOG3 vw_send: To DATATAKING: hdrldsrcnm "galfasrc" 2009-Mar-14 21:49:22 LOG3 vw_send: To DATATAKING: set ra 085200.0 2009-Mar-14 21:49:22 LOG3 vw_send: To DATATAKING: set dec +215400 2009-Mar-14 21:49:22 LOG3 vw_send: To DATATAKING: pnt tr send 2009-Mar-14 21:49:22 LOG3 vw_send: To DATATAKING: pnt tr 085200.0 +215400 -CJ 2009-Mar-14 21:49:22 LOG3 vw_send: To DATATAKING: dopsetvel 0 topo 2009-Mar-14 21:49:22 STOP finish_task: Finishing task 'sending tracking commands' 2009-Mar-14 21:49:22 LOG5 finish_task: Level: (2) ID = <10003> Status = 0 0 0 0 ok 2009-Mar-14 21:49:22 INFO2 finish_task: DONE finished sending: tracking commands 2009-Mar-14 21:49:22 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 21:49:22 STOP end_task: Finishing task 'sending tracking commands' with status 'OK' 2009-Mar-14 21:49:22 LOG5 end_task: Level: (2) ID = <10003> Status = 0 0 0 0 ok 2009-Mar-14 21:49:22 LOG4 apply_pointing_corr: Calling 'apply_pointing_corr 0 0 0 0 0' 2009-Mar-14 21:49:22 START begin_task: Starting task 'applying pointing corrections' 2009-Mar-14 21:49:22 LOG5 begin_task: Level: (2) ID = <10004> Status = 0 0 0 0 ok 2009-Mar-14 21:49:22 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Applying Pointing Corrections} INFO {Applying pointing corrections ...} 2009-Mar-14 21:49:22 LOG3 vw_send: To DATATAKING: pnt cor setoff 0.0 0.0 2009-Mar-14 21:49:22 STOP finish_task: Finishing task 'applying pointing corrections' 2009-Mar-14 21:49:22 LOG5 finish_task: Level: (2) ID = <10004> Status = 0 0 0 0 ok 2009-Mar-14 21:49:22 INFO2 finish_task: DONE finished applying: pointing corrections 2009-Mar-14 21:49:22 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 21:49:22 STOP end_task: Finishing task 'applying pointing corrections' with status 'OK' 2009-Mar-14 21:49:22 LOG5 end_task: Level: (2) ID = <10004> Status = 0 0 0 0 ok 2009-Mar-14 21:49:22 STOP finish_task: Finishing task 'selecting new source' 2009-Mar-14 21:49:22 LOG5 finish_task: Level: (1) ID = <10002> Status = 0 0 0 0 ok 2009-Mar-14 21:49:22 DONE finish_task: DONE finished selecting: new source 2009-Mar-14 21:49:22 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 21:49:22 END end_task: Finishing task 'selecting new source' with status 'OK' 2009-Mar-14 21:49:22 LOG5 end_task: Level: (1) ID = <10002> Status = 0 0 0 0 ok 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: hdrldsrcnm "galfasrc" 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: set ra 085200.0 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: set dec +215400 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: vw% 085200.0 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: vw% +215400 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: pnt tr send 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: pnt tr 085200.0 +215400 -CJ 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: dopsetvel 0 topo 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: vw% vw% vw% 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: pnt cor setoff 0.0 0.0 2009-Mar-14 21:49:22 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:51:13 INFO4 CIMA-load_command_file: Loaded command file 'command_galfasrc09.cmd' 2009-Mar-14 21:51:51 INFO1 CIMA-run_command_file: Transferring command file 'command_galfasrc09.cmd' to executive ... 2009-Mar-14 21:51:51 LOG4 exec_msg: From OBSERVER: store_command_file_line 1 5 {LOAD togs_09.conf} 2009-Mar-14 21:51:51 LOG4 exec_msg: From OBSERVER: store_command_file_line 2 6 {CATALOG a2010.cat} 2009-Mar-14 21:51:51 LOG4 exec_msg: From OBSERVER: store_command_file_line 3 7 {GOTO galfasrc} 2009-Mar-14 21:51:51 LOG4 exec_msg: From OBSERVER: store_command_file_line 4 8 {ALFAANGLE 19} 2009-Mar-14 21:51:51 LOG4 exec_msg: From OBSERVER: store_command_file_line 5 9 {WAITTRACK} 2009-Mar-14 21:51:51 LOG4 exec_msg: From OBSERVER: store_command_file_line 6 13 {SMARTFREQ secs=10 loops=2 caltype=hcorcal adjpwr=first newfile=one freqs={1380.60607910 1383.34045410 1383.53576660 1384.12170410 1385.29357910 1385.68420410 1386.66076660}} 2009-Mar-14 21:51:51 COMMAND CIMA-send_to_exec: Sending command to run command file 2009-Mar-14 21:51:51 LOG4 exec_msg: From OBSERVER: run_command_file command_galfasrc09.cmd 1 1 6 2009-Mar-14 21:51:51 LOG4 run_command_file: Calling 'run_command_file command_galfasrc09.cmd 1 1 6' 2009-Mar-14 21:51:51 BEGIN begin_task: Starting task 'running command file 'command_galfasrc09.cmd'' 2009-Mar-14 21:51:51 LOG5 begin_task: Level: (1) ID = <10005> Status = 0 0 0 0 ok 2009-Mar-14 21:51:51 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Running Command File} INFO {Running command file 'command_galfasrc09.cmd' ...} 2009-Mar-14 21:51:51 NOTE run_command_file: Starting execution of command file 'command_galfasrc09.cmd' from line 1 2009-Mar-14 21:51:51 COMMAND run_command_line: EXECUTING command 5: 'LOAD togs_09.conf' 2009-Mar-14 21:51:51 LOG1 execute_load: Waiting for CIMA frontend to check the IF/LO file 2009-Mar-14 21:51:51 LOG4 exec_msg: From OBSERVER: global comfile ; set comfile(frontend_status) ok 2009-Mar-14 21:51:51 LOG1 execute_load: Waiting for CIMA frontend to load the IF/LO file 2009-Mar-14 21:51:52 NOTE CIMA-load_config_file: Loading configuration file 'togs_09.conf' 2009-Mar-14 21:51:52 LOG2 CIMA-antvel: Precessing RA = 08:52:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:51:52 LOG2 CIMA-antvel: Computed apparent RA = 08:52:34.0 Dec = +21:51:51.8 2009-Mar-14 21:51:52 LOG2 CIMA-antvel: Parameters to Doppler: Topocentric 93111 2009 73 0.0 2009-Mar-14 21:51:52 INFO5 CIMA-antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(fast_config) "yes" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(config_type) "standard" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(receiver) "alfa" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(quick_tsys) "no" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(ifsetup_only) "no" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(retrack_source) "no" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(path) "ALFA" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(restcent) "1385.0" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest1) "1385.0" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest2) "1385.0" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest3) "1385.0" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest4) "1385.0" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest5) "1385.0" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest6) "1385.0" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest7) "1385.0" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest8) "1385.0" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(dest1) "250" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(dest2) "250" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(dest3) "250" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(dest4) "250" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq1) "0.000000" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq2) "0.000000" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq3) "0.000000" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq4) "0.000000" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq5) "0.000000" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq6) "0.000000" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq7) "0.000000" 2009-Mar-14 21:51:52 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq8) "0.000000" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(calctype) "SUBBAND" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(backends) "WAPP+GALFA" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(radarblanker) "off" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(polsel) "skip" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(filtersel) "alfafb 1" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(sbshcl) "T" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(shcl) "skip" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rfnum) "skip" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(zmnormal) "T" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rfattn) "11 11" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(ifnum) "6" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(up) "1635.000000" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(ifattn) "0 0" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(fiber) "T" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(ac2sw) "skip" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(phbsig) "skip" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(hybrid) "skip" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(phblo) "skip" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(xfnormal) "T" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(sigsrc) "gr" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(gain) "8 8" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(inpfrq) "alfa" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(mixer) "750 750 750 750 750 750 750 750" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(vlbainp) "skip" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(syndest) "3 3 3 3 3 3 3 3" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(calsrc) "3" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(750nb) "skip" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(2to12wb) "F" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(calrcvr) "15" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(2a2b30if) "skip" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(vis30mhz) "gr" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(430blnk) "F" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw1) "100" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw2) "100" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw3) "100" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw4) "100" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_enabled1) "1" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_enabled2) "1" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_enabled3) "1" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_enabled4) "1" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_cfg1) "2 chan, 3-level" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_cfg2) "2 chan, 3-level" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_cfg3) "2 chan, 3-level" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_cfg4) "2 chan, 3-level" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw1) "100" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw2) "100" 2009-Mar-14 21:51:53 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw3) "100" 2009-Mar-14 21:51:54 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw4) "100" 2009-Mar-14 21:51:54 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_dumptime) "1" 2009-Mar-14 21:51:54 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(alfa) "1" 2009-Mar-14 21:51:54 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(dual) "1" 2009-Mar-14 21:51:54 LOG4 exec_msg: From OBSERVER: global comfile ; set comfile(frontend_status) ok 2009-Mar-14 21:51:54 BEGIN begin_task: Starting task 'configuring IF/LO path' 2009-Mar-14 21:51:54 LOG5 begin_task: Level: (2) ID = <10006> Status = 0 0 0 0 ok 2009-Mar-14 21:51:54 INFO1 config_iflo: Starting to configure IF/LO path for ALFA 2009-Mar-14 21:51:54 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Configuring IF/LO path} TASKWAIT BITMAP stat_iflo INFO {Setting up the IF/LO path ...} 2009-Mar-14 21:51:54 INFO1 config_iflo: Selecting receiver ALFA 2009-Mar-14 21:51:54 LOG4 send_obs_status: To obs_status: <1> INFO {Selecting receiver ALFA} 2009-Mar-14 21:51:54 LOG1 select_receiver: Calling 'select_receiver alfa no no no' 2009-Mar-14 21:51:54 START begin_task: Starting task 'selecting receiver ALFA' 2009-Mar-14 21:51:54 LOG5 begin_task: Level: (3) ID = <10007> Status = 0 0 0 0 ok 2009-Mar-14 21:51:54 NOTE select_receiver: Starting to select receiver ALFA 2009-Mar-14 21:51:54 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Receiver Selection} TOTALLOOPS 1 TASKWAIT BITMAP stat_alfa_rot INFO {Selecting receiver ALFA ...} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: setupall alfa 1375.0 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: acvlbical off 2009-Mar-14 21:51:54 NOTE select_receiver: Don't forget to choose a source after receiver selection! 2009-Mar-14 21:51:54 STOP finish_task: Finishing task 'selecting receiver ALFA' 2009-Mar-14 21:51:54 LOG5 finish_task: Level: (3) ID = <10007> Status = 0 0 0 0 ok 2009-Mar-14 21:51:54 INFO2 finish_task: DONE finished selecting: receiver ALFA 2009-Mar-14 21:51:54 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 21:51:54 STOP end_task: Finishing task 'selecting receiver ALFA' with status 'OK' 2009-Mar-14 21:51:54 LOG5 end_task: Level: (3) ID = <10007> Status = 0 0 0 0 ok 2009-Mar-14 21:51:54 START begin_task: Starting task 'waiting for receiver ALFA' 2009-Mar-14 21:51:54 LOG5 begin_task: Level: (3) ID = <10008> Status = 0 0 0 0 ok 2009-Mar-14 21:51:54 STOP end_task: Finishing task 'waiting for receiver ALFA' with status 'OK' 2009-Mar-14 21:51:54 LOG5 end_task: Level: (3) ID = <10008> Status = 0 0 0 0 ok 2009-Mar-14 21:51:54 INFO1 config_iflo: Configuring rest of the IF/LO path 2009-Mar-14 21:51:54 LOG4 send_obs_status: To obs_status: <1> BITMAP stat_iflo INFO {Configuring rest of the IF/LO path} 2009-Mar-14 21:51:54 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 21:51:54 LOG3 socket_wait: To ALFAMON: NOISE ACTIVE 2009-Mar-14 21:51:54 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 21:51:54 LOG5 begin_task: Level: (3) ID = <10009> Status = 0 0 0 0 ok 2009-Mar-14 21:51:54 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 21:51:54 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 21:51:54 LOG5 end_task: Level: (3) ID = <10009> Status = 0 0 0 0 ok 2009-Mar-14 21:51:54 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 21:51:54 LOG3 to_alfamon: To ALFAMON: NOISE ACTIVE 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: alfafb 1 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if1 {if1_sbshcl T} 2009-Mar-14 21:51:54 LOG5 send_ifx: Skipping if1-command 'if1_shcl skip' since not applicable 2009-Mar-14 21:51:54 LOG5 send_ifx: Skipping if1-command 'if1_rfnum skip' since not applicable 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if1 {if1_zmnormal T} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if1 {if1_rfattn 11 11} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if1 {if1_ifnum 6} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635000000.0} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if1 {if1_ifattn 0 0} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if1 {if1_fiber T} 2009-Mar-14 21:51:54 LOG5 send_ifx: Skipping if1-command 'if1_ac2sw skip' since not applicable 2009-Mar-14 21:51:54 LOG5 send_ifx: Skipping if1-command 'if1_phbsig skip' since not applicable 2009-Mar-14 21:51:54 LOG5 send_ifx: Skipping if1-command 'if1_hybrid skip' since not applicable 2009-Mar-14 21:51:54 LOG5 send_ifx: Skipping if1-command 'if1_phblo skip' since not applicable 2009-Mar-14 21:51:54 LOG5 send_ifx: Skipping if1-command 'if1_750nb skip' since not applicable 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if1 {if1_2to12wb F} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if1 {if1_calrcvr 15} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if2 {if2_xfnormal T} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if2 {if2_sigsrc gr} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if2 {if2_gain 8 8} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if2 {if2_inpfrq alfa} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if2 {if2_mixer 750 750 750 750 750 750 750 750} 2009-Mar-14 21:51:54 LOG5 send_ifx: Skipping if2-command 'if2_vlbainp skip' since not applicable 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if2 {if2_syndest 3 3 3 3 3 3 3 3} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if2 {if2_calsrc 3} 2009-Mar-14 21:51:54 LOG5 send_ifx: Skipping if2-command 'if2_2a2b30if skip' since not applicable 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if2 {if2_vis30mhz gr} 2009-Mar-14 21:51:54 LOG3 vw_send: To DATATAKING: if2 {if2_430blnk F} 2009-Mar-14 21:51:54 LOG2 socket_wait: Starting sockwait on DATATAKING for 'configuring IF/LO path' using string 'DONE' 2009-Mar-14 21:51:54 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 21:51:54 START begin_task: Starting task 'waiting on configuring IF/LO path' 2009-Mar-14 21:51:54 LOG5 begin_task: Level: (3) ID = <10010> Status = 0 0 0 0 ok 2009-Mar-14 21:51:54 LOG4 got_cormsg: From DATATAKING: setupall alfa 1375.0 2009-Mar-14 21:51:54 LOG4 got_cormsg: From DATATAKING: acvlbical off 2009-Mar-14 21:51:54 LOG4 got_cormsg: From DATATAKING: alfafb 1 2009-Mar-14 21:51:54 LOG4 got_cormsg: From DATATAKING: if1 {if1_sbshcl T} 2009-Mar-14 21:51:54 LOG4 got_cormsg: From DATATAKING: if1 {if1_zmnormal T} 2009-Mar-14 21:51:54 LOG4 got_cormsg: From DATATAKING: if1 {if1_rfattn 11 11} 2009-Mar-14 21:51:54 LOG4 got_cormsg: From DATATAKING: if1 {if1_ifnum 6} 2009-Mar-14 21:51:54 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635000000.0} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if1 {if1_ifattn 0 0} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if1 {if1_fiber T} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if1 {if1_2to12wb F} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if1 {if1_calrcvr 15} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if2 {if2_xfnormal T} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if2 {if2_sigsrc gr} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if2 {if2_gain 8 8} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if2 {if2_inpfrq alfa} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if2 {if2_mixer 750 750 750 750 750 750 750 750} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if2 {if2_syndest 3 3 3 3 3 3 3 3} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if2 {if2_calsrc 3} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if2 {if2_vis30mhz gr} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: if2 {if2_430blnk F} 2009-Mar-14 21:51:55 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 21:52:01 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:03 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:03 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:07 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:07 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:08 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:08 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:09 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:09 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:09 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:09 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:09 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:09 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:10 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:10 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:10 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:10 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:10 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:10 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:10 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 21:52:10 STOP end_task: Finishing task 'waiting on configuring IF/LO path' with status 'OK' 2009-Mar-14 21:52:10 LOG5 end_task: Level: (3) ID = <10010> Status = 0 0 0 0 ok 2009-Mar-14 21:52:10 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'configuring IF/LO path' 2009-Mar-14 21:52:10 STOP finish_task: Finishing task 'configuring IF/LO path' 2009-Mar-14 21:52:10 LOG5 finish_task: Level: (2) ID = <10006> Status = 0 0 0 0 ok 2009-Mar-14 21:52:10 DONE finish_task: DONE finished configuration: IF/LO path 2009-Mar-14 21:52:11 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 21:52:11 END end_task: Finishing task 'configuring IF/LO path' with status 'OK' 2009-Mar-14 21:52:11 LOG5 end_task: Level: (2) ID = <10006> Status = 0 0 0 0 ok 2009-Mar-14 21:52:11 BEGIN begin_task: Starting task 'configuring WAPPs' 2009-Mar-14 21:52:11 LOG5 begin_task: Level: (2) ID = <10011> Status = 0 0 0 0 ok 2009-Mar-14 21:52:11 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Configuring WAPPs} TASKWAIT BITMAP stat_corr INFO {Configuring the WAPPs ...} 2009-Mar-14 21:52:11 INFO1 config_wapp_correlator: Starting to configure WAPP as correlator 2009-Mar-14 21:52:11 LOG2 set_cal_source: Setting cal signal control to the WAPPs 2009-Mar-14 21:52:11 START begin_task: Starting task 'selecting calibration port' 2009-Mar-14 21:52:11 LOG5 begin_task: Level: (3) ID = <10012> Status = 0 0 0 0 ok 2009-Mar-14 21:52:11 LOG3 vw_send: To DATATAKING: calport 3 2009-Mar-14 21:52:11 LOG2 socket_wait: Starting sockwait on DATATAKING for 'calport' using string 'DONE' 2009-Mar-14 21:52:11 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 21:52:11 START begin_task: Starting task 'waiting on calport' 2009-Mar-14 21:52:11 LOG5 begin_task: Level: (4) ID = <10013> Status = 0 0 0 0 ok 2009-Mar-14 21:52:11 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:11 LOG4 got_cormsg: From DATATAKING: calport 3 2009-Mar-14 21:52:11 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 21:52:11 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:11 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 21:52:11 STOP end_task: Finishing task 'waiting on calport' with status 'OK' 2009-Mar-14 21:52:11 LOG5 end_task: Level: (4) ID = <10013> Status = 0 0 0 0 ok 2009-Mar-14 21:52:11 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'calport' 2009-Mar-14 21:52:11 STOP end_task: Finishing task 'selecting calibration port' with status 'OK' 2009-Mar-14 21:52:11 LOG5 end_task: Level: (3) ID = <10012> Status = 0 0 0 0 ok 2009-Mar-14 21:52:11 LOG3 wapp_calcontrol: To CALCONTROL: CALOFF 2009-Mar-14 21:52:11 LOG3 sock_errsend: To CALCONTROL: CALOFF STATUS 2009-Mar-14 21:52:11 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 21:52:11 LOG5 begin_task: Level: (3) ID = <10014> Status = 0 0 0 0 ok 2009-Mar-14 21:52:11 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 21:52:11 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:11 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 21:52:11 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 21:52:11 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 21:52:11 LOG5 end_task: Level: (3) ID = <10014> Status = 0 0 0 0 ok 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON: VERBOSE 0 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON2: VERBOSE 0 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON3: VERBOSE 0 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON4: VERBOSE 0 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON: TIMEOUT 5 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON2: TIMEOUT 5 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON3: TIMEOUT 5 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON4: TIMEOUT 5 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON2: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON3: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:52:11 LOG3 send_to_one_wapp: To WAPPCON4: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:52:11 LOG3 wapp_calcontrol: To CALCONTROL: TRIGCLOCK 2009-Mar-14 21:52:11 LOG3 sock_errsend: To CALCONTROL: TRIGCLOCK STATUS 2009-Mar-14 21:52:11 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 21:52:11 LOG5 begin_task: Level: (3) ID = <10015> Status = 0 0 0 0 ok 2009-Mar-14 21:52:11 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 21:52:11 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 21:52:11 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 21:52:11 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 21:52:11 LOG5 end_task: Level: (3) ID = <10015> Status = 0 0 0 0 ok 2009-Mar-14 21:52:12 LOG3 send_to_one_wapp: To WAPPCON: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:52:12 LOG3 send_to_one_wapp: To WAPPCON2: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:52:12 LOG3 send_to_one_wapp: To WAPPCON3: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:52:12 LOG3 send_to_one_wapp: To WAPPCON4: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:52:12 STOP finish_task: Finishing task 'configuring WAPPs' 2009-Mar-14 21:52:12 LOG5 finish_task: Level: (2) ID = <10011> Status = 0 0 0 0 ok 2009-Mar-14 21:52:12 DONE finish_task: DONE finished configuring: the WAPPs in ALFA mode 2009-Mar-14 21:52:12 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 21:52:12 END end_task: Finishing task 'configuring WAPPs' with status 'OK' 2009-Mar-14 21:52:12 LOG5 end_task: Level: (2) ID = <10011> Status = 0 0 0 0 ok 2009-Mar-14 21:52:12 COMMAND run_command_line: EXECUTING command 6: 'CATALOG a2010.cat' 2009-Mar-14 21:52:12 INFO1 execute_catalog: Selecting new catalog '/share/obs4/usr/a2010/a2010.cat' 2009-Mar-14 21:52:12 COMMAND run_command_line: EXECUTING command 7: 'GOTO galfasrc' 2009-Mar-14 21:52:12 LOG4 goto_source: Calling 'goto_source /share/obs4/usr/a2010/a2010.cat galfasrc nooffset nowait' 2009-Mar-14 21:52:12 BEGIN begin_task: Starting task 'tracking source 'galfasrc'' 2009-Mar-14 21:52:12 LOG5 begin_task: Level: (2) ID = <10016> Status = 0 0 0 0 ok 2009-Mar-14 21:52:12 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Tracking Source} INFO {Tracking source 'galfasrc' ...} 2009-Mar-14 21:52:12 LOG3 track_source: Calling 'track_source galfasrc 085800.0 +215400 J 0.0 0.0 main small /share/obs4/usr/a2010/a2010.cat 0 Topocentric velocity(optical)' 2009-Mar-14 21:52:12 START begin_task: Starting task 'sending tracking commands' 2009-Mar-14 21:52:12 LOG5 begin_task: Level: (3) ID = <10017> Status = 0 0 0 0 ok 2009-Mar-14 21:52:12 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Sending Tracking Commands} SOURCE {galfasrc} INFO {Slewing to source 'galfasrc' ...} 2009-Mar-14 21:52:12 INFO1 track_source: Starting to track galfasrc 2009-Mar-14 21:52:12 LOG3 vw_send: To DATATAKING: hdrldsrcnm "galfasrc" 2009-Mar-14 21:52:12 LOG3 vw_send: To DATATAKING: set ra 085800.0 2009-Mar-14 21:52:12 LOG3 vw_send: To DATATAKING: set dec +215400 2009-Mar-14 21:52:12 LOG3 vw_send: To DATATAKING: pnt tr send 2009-Mar-14 21:52:12 LOG3 vw_send: To DATATAKING: pnt tr 085800.0 +215400 -CJ 2009-Mar-14 21:52:12 LOG3 vw_send: To DATATAKING: dopsetvel 0 topo 2009-Mar-14 21:52:12 STOP finish_task: Finishing task 'sending tracking commands' 2009-Mar-14 21:52:12 LOG5 finish_task: Level: (3) ID = <10017> Status = 0 0 0 0 ok 2009-Mar-14 21:52:12 INFO2 finish_task: DONE finished sending: tracking commands 2009-Mar-14 21:52:12 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 21:52:12 STOP end_task: Finishing task 'sending tracking commands' with status 'OK' 2009-Mar-14 21:52:12 LOG5 end_task: Level: (3) ID = <10017> Status = 0 0 0 0 ok 2009-Mar-14 21:52:13 STOP finish_task: Finishing task 'tracking source 'galfasrc'' 2009-Mar-14 21:52:13 LOG5 finish_task: Level: (2) ID = <10016> Status = 0 0 0 0 ok 2009-Mar-14 21:52:13 DONE finish_task: DONE finished tracking: source 'galfasrc' 2009-Mar-14 21:52:13 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 21:52:13 END end_task: Finishing task 'tracking source 'galfasrc'' with status 'OK' 2009-Mar-14 21:52:13 LOG5 end_task: Level: (2) ID = <10016> Status = 0 0 0 0 ok 2009-Mar-14 21:52:13 COMMAND run_command_line: EXECUTING command 8: 'ALFAANGLE 19' 2009-Mar-14 21:52:13 INFO1 execute_alfaangle: Setting the ALFA rotation angle to 19 2009-Mar-14 21:52:13 BEGIN begin_task: Starting task 'rotate ALFA to +19 degrees' 2009-Mar-14 21:52:13 LOG5 begin_task: Level: (2) ID = <10018> Status = 0 0 0 0 ok 2009-Mar-14 21:52:13 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Rotating ALFA} INFO {Rotating ALFA to +19 degrees ...} 2009-Mar-14 21:52:13 INFO2 rotate_alfa: ALFA commanded to +19.0 degrees 2009-Mar-14 21:52:13 LOG3 sock_errsend: To ALFAMOTOR: POSITION 19 REPLY 2009-Mar-14 21:52:13 LOG4 send_obs_status: To obs_status: <1> TASKWAIT BITMAP stat_alfa_rot MESSAGE {Waiting for ALFA to rotate into position ...} 2009-Mar-14 21:52:13 START begin_task: Starting task 'waiting on ALFA rotation' 2009-Mar-14 21:52:13 LOG5 begin_task: Level: (3) ID = <10019> Status = 0 0 0 0 ok 2009-Mar-14 21:52:13 NOTE WAPPDATA-new_file: New FITS file: wapp.20090314.a2010.0029.fits 2009-Mar-14 21:52:13 LOG4 WAPP=1+2+3+4-wappcon: Received command 'PROJECT a2010 Lyle Hoffman' 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: hdrldsrcnm "galfasrc" 2009-Mar-14 21:52:13 LOG4 WAPP=1+2+3+4-wappcon: Received command 'VERBOSE 0' 2009-Mar-14 21:52:13 LOG4 WAPP=1+2+3+4-wappcon: Received command 'TIMEOUT 5' 2009-Mar-14 21:52:13 LOG4 send_obs_status: To obs_status: <1> FILENAME {wapp.20090314.a2010.0029.fits} 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: set ra 085800.0 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: set dec +215400 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: vw% 085800.0 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: vw% +215400 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: pnt tr send 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: pnt tr 085800.0 +215400 -CJ 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: dopsetvel 0 topo 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: vw% vw% 2009-Mar-14 21:52:13 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:52:13 LOG4 WAPP=1+2+3+4-wappcon: Received command 'PROJECT a2010 Lyle Hoffman' 2009-Mar-14 21:52:45 LOG4 exec_msg: From ALFAMOTOR: alfa_motor "INPOSITION" 2009-Mar-14 21:52:45 INFO3 alfa_motor: ALFA rotator in-position +19.00 degrees 2009-Mar-14 21:52:45 STOP end_task: Finishing task 'waiting on ALFA rotation' with status 'OK' 2009-Mar-14 21:52:45 LOG5 end_task: Level: (3) ID = <10019> Status = 0 0 0 0 ok 2009-Mar-14 21:52:45 LOG4 send_obs_status: To obs_status: <1> CLEARTIME BITMAP stat_busy 2009-Mar-14 21:52:45 STOP finish_task: Finishing task 'rotate ALFA to +19 degrees' 2009-Mar-14 21:52:45 LOG5 finish_task: Level: (2) ID = <10018> Status = 0 0 0 0 ok 2009-Mar-14 21:52:45 DONE finish_task: DONE finished configuration: rotating ALFA to +19 degrees 2009-Mar-14 21:52:45 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 21:52:45 END end_task: Finishing task 'rotate ALFA to +19 degrees' with status 'OK' 2009-Mar-14 21:52:45 LOG5 end_task: Level: (2) ID = <10018> Status = 0 0 0 0 ok 2009-Mar-14 21:52:45 COMMAND run_command_line: EXECUTING command 9: 'WAITTRACK' 2009-Mar-14 21:52:45 BEGIN begin_task: Starting task 'waiting on telescope' 2009-Mar-14 21:52:45 LOG5 begin_task: Level: (2) ID = <10020> Status = 0 0 0 0 ok 2009-Mar-14 21:52:45 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Waiting On Telescope} TASKWAIT BITMAP stat_slew INFO {Waiting for telescope to track source ...} 2009-Mar-14 21:52:46 LOG3 waittrk: Start waittrk 5 2009-Mar-14 21:52:46 START begin_task: Starting task 'waiting on telescope movement' 2009-Mar-14 21:52:46 LOG5 begin_task: Level: (3) ID = <10021> Status = 0 0 0 0 ok 2009-Mar-14 21:52:51 STOP end_task: Finishing task 'waiting on telescope movement' with status 'OK' 2009-Mar-14 21:52:51 LOG5 end_task: Level: (3) ID = <10021> Status = 0 0 0 0 ok 2009-Mar-14 21:52:51 START begin_task: Starting task 'waiting on telescope on source' 2009-Mar-14 21:52:51 LOG5 begin_task: Level: (3) ID = <10022> Status = 0 0 0 0 ok 2009-Mar-14 21:53:08 STOP end_task: Finishing task 'waiting on telescope on source' with status 'OK' 2009-Mar-14 21:53:08 LOG5 end_task: Level: (3) ID = <10022> Status = 0 0 0 0 ok 2009-Mar-14 21:53:08 LOG4 send_obs_status: To obs_status: <1> CLEARTIME BITMAP stat_busy 2009-Mar-14 21:53:08 INFO2 waittrk: Now tracking galfasrc 2009-Mar-14 21:53:08 LOG4 waittrk: Current telescope position: Az = 184.25 ZA = 3.54 2009-Mar-14 21:53:08 STOP finish_task: Finishing task 'waiting on telescope' 2009-Mar-14 21:53:08 LOG5 finish_task: Level: (2) ID = <10020> Status = 0 0 0 0 ok 2009-Mar-14 21:53:08 DONE finish_task: DONE finished waiting: telescope on source 2009-Mar-14 21:53:08 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 21:53:08 END end_task: Finishing task 'waiting on telescope' with status 'OK' 2009-Mar-14 21:53:08 LOG5 end_task: Level: (2) ID = <10020> Status = 0 0 0 0 ok 2009-Mar-14 21:53:08 COMMAND run_command_line: EXECUTING command 13: 'SMARTFREQ secs=10 loops=2 caltype=hcorcal adjpwr=first newfile=one freqs={1380.60607910 1383.34045410 1383.53576660 1384.12170410 1385.29357910 1385.68420410 1386.66076660}' 2009-Mar-14 21:53:08 LOG2 check_obsmode: Waiting for CIMA frontend to check the options for 'smart frequency switching' 2009-Mar-14 21:53:09 LOG4 exec_msg: From OBSERVER: global comfile ; set comfile(frontend_status) ok 2009-Mar-14 21:53:09 LOG1 smartfreq: Calling 'smartfreq 2 10 hcorcal first one {1380.60607910 1383.34045410 1383.53576660 1384.12170410 1385.29357910 1385.68420410 1386.66076660}' 2009-Mar-14 21:53:09 BEGIN begin_task: Starting task 'smart frequency switching' 2009-Mar-14 21:53:09 LOG5 begin_task: Level: (2) ID = <10023> Status = 0 0 0 0 ok 2009-Mar-14 21:53:09 INFO4 begin_task: MAKING 'smart frequency switching' using 'alfa' + 'WAPP+GALFA' on 'galfasrc' 2009-Mar-14 21:53:09 INFO1 smartfreq: Starting pattern: Smart frequency switching 2009-Mar-14 21:53:09 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Smart frequency switching} TOTALLOOPS 2 INFO {Starting smart frequency switching obs. ...} 2009-Mar-14 21:53:09 START begin_task: Starting task 'selecting calibration type' 2009-Mar-14 21:53:09 LOG5 begin_task: Level: (3) ID = <10024> Status = 0 0 0 0 ok 2009-Mar-14 21:53:09 LOG3 vw_send: To DATATAKING: setcal hcorcal 2009-Mar-14 21:53:09 LOG2 socket_wait: Starting sockwait on DATATAKING for 'setcal' using string 'DONE' 2009-Mar-14 21:53:09 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 21:53:09 START begin_task: Starting task 'waiting on setcal' 2009-Mar-14 21:53:09 LOG5 begin_task: Level: (4) ID = <10025> Status = 0 0 0 0 ok 2009-Mar-14 21:53:09 LOG4 got_cormsg: From DATATAKING: setcal hcorcal 2009-Mar-14 21:53:09 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 21:53:09 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:09 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 21:53:09 STOP end_task: Finishing task 'waiting on setcal' with status 'OK' 2009-Mar-14 21:53:09 LOG5 end_task: Level: (4) ID = <10025> Status = 0 0 0 0 ok 2009-Mar-14 21:53:09 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'setcal' 2009-Mar-14 21:53:09 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 21:53:09 LOG3 socket_wait: To ALFAMON: CAL HI 2009-Mar-14 21:53:09 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 21:53:09 LOG5 begin_task: Level: (4) ID = <10026> Status = 0 0 0 0 ok 2009-Mar-14 21:53:09 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:09 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 21:53:09 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 21:53:09 LOG5 end_task: Level: (4) ID = <10026> Status = 0 0 0 0 ok 2009-Mar-14 21:53:09 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 21:53:09 LOG3 to_alfamon: To ALFAMON: CAL HI 2009-Mar-14 21:53:09 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 21:53:09 LOG3 socket_wait: To ALFAMON: NOISE ACTIVE 2009-Mar-14 21:53:09 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 21:53:09 LOG5 begin_task: Level: (4) ID = <10027> Status = 0 0 0 0 ok 2009-Mar-14 21:53:09 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 21:53:09 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 21:53:09 LOG5 end_task: Level: (4) ID = <10027> Status = 0 0 0 0 ok 2009-Mar-14 21:53:09 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 21:53:09 LOG3 to_alfamon: To ALFAMON: NOISE ACTIVE 2009-Mar-14 21:53:09 STOP end_task: Finishing task 'selecting calibration type' with status 'OK' 2009-Mar-14 21:53:09 LOG5 end_task: Level: (3) ID = <10024> Status = 0 0 0 0 ok 2009-Mar-14 21:53:09 LOG3 send_to_one_wapp: To WAPPCON: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:53:09 LOG3 send_to_one_wapp: To WAPPCON2: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:53:09 LOG3 send_to_one_wapp: To WAPPCON3: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:53:09 LOG3 send_to_one_wapp: To WAPPCON4: PROJECT a2010 Lyle Hoffman 2009-Mar-14 21:53:09 INFO5 new_file: There is no need to start a new FITS-file since the current one 'wapp.20090314.a2010.0029.fits' is empty! 2009-Mar-14 21:53:09 INFO2 smartfreq: Starting smart frequency switching loop 1 of 2 2009-Mar-14 21:53:09 LOG4 send_obs_status: To obs_status: <1> LOOP 1 2009-Mar-14 21:53:09 LOG4 send_obs_status: To obs_status: <1> BITMAP stat_cal_off INFO {Making 7 CAL-OFFs followed by 7 CAL-ONs} MESSAGE {Setting CAL-OFF ...} 2009-Mar-14 21:53:09 LOG3 wapp_calcontrol: To CALCONTROL: CALOFF 2009-Mar-14 21:53:09 LOG3 sock_errsend: To CALCONTROL: CALOFF STATUS 2009-Mar-14 21:53:10 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 21:53:10 LOG5 begin_task: Level: (3) ID = <10028> Status = 0 0 0 0 ok 2009-Mar-14 21:53:10 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 21:53:10 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 21:53:10 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 21:53:10 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 21:53:10 LOG5 end_task: Level: (3) ID = <10028> Status = 0 0 0 0 ok 2009-Mar-14 21:53:10 LOG4 send_obs_status: To obs_status: <1> TOTALPARTS 2*7 2009-Mar-14 21:53:10 START begin_task: Starting task 'adjusting WAPP power' 2009-Mar-14 21:53:10 LOG5 begin_task: Level: (3) ID = <10029> Status = 0 0 0 0 ok 2009-Mar-14 21:53:10 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Adjusting WAPP power} TASKWAIT BITMAP stat_power INFO {Adjusting WAPP power ...} 2009-Mar-14 21:53:10 INFO2 adjust_power: Starting to adjust WAPP power 2009-Mar-14 21:53:10 LOG3 vw_send: To DATATAKING: adjpwrif2 2009-Mar-14 21:53:10 LOG2 socket_wait: Starting sockwait on DATATAKING for 'adjpwrif2' using string 'DONE' 2009-Mar-14 21:53:10 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 21:53:10 START begin_task: Starting task 'waiting on adjpwrif2' 2009-Mar-14 21:53:10 LOG5 begin_task: Level: (4) ID = <10030> Status = 0 0 0 0 ok 2009-Mar-14 21:53:10 LOG4 got_cormsg: From DATATAKING: adjpwrif2 2009-Mar-14 21:53:10 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 21:53:10 LOG4 WAPP=1+2+3+4-wappcon: Received command 'PROJECT a2010 Lyle Hoffman' 2009-Mar-14 21:53:12 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:13 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 21:53:13 STOP end_task: Finishing task 'waiting on adjpwrif2' with status 'OK' 2009-Mar-14 21:53:13 LOG5 end_task: Level: (4) ID = <10030> Status = 0 0 0 0 ok 2009-Mar-14 21:53:13 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'adjpwrif2' 2009-Mar-14 21:53:13 START begin_task: Starting task 'adjusting WAPP power' 2009-Mar-14 21:53:13 LOG5 begin_task: Level: (4) ID = <10031> Status = 0 0 0 0 ok 2009-Mar-14 21:53:13 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Adjusting WAPP Power} TASKWAIT BITMAP stat_power INFO {Adjusting power ...} 2009-Mar-14 21:53:13 LOG3 sock_errsend: To WAPPCON: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 21:53:13 LOG3 sock_errsend: To WAPPCON2: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 21:53:13 LOG3 sock_errsend: To WAPPCON3: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 21:53:13 LOG3 sock_errsend: To WAPPCON4: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 21:53:13 START begin_task: Starting task 'waiting on adjust WAPP power' 2009-Mar-14 21:53:13 LOG5 begin_task: Level: (5) ID = <10032> Status = 0 0 0 0 ok 2009-Mar-14 21:53:13 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:13 LOG4 WAPP=1+2+3+4-wappcon: Received command 'ADJUSTPOWER 100 1 2 0 1 1' 2009-Mar-14 21:53:13 INFO2 WAPP=1-auto_atten_dual: Attenuators beam 0: 7 6 dB --- beam 1: 6 6 dB 2009-Mar-14 21:53:13 INFO2 WAPP=3-auto_atten_dual: Attenuators beam 4: 2 1 dB --- beam 5: 5 3 dB 2009-Mar-14 21:53:13 INFO2 WAPP=2-auto_atten_dual: Attenuators beam 2: 6 4 dB --- beam 3: 3 2 dB 2009-Mar-14 21:53:13 INFO2 WAPP=4-auto_atten_dual: Attenuators beam 6: 3 0 dB --- beam 7: 2 0 dB 2009-Mar-14 21:53:13 INFO1 WAPP=1+2+3+4-adjust_power: DONE adjusting power 2009-Mar-14 21:53:13 STOP end_task: Finishing task 'waiting on adjust WAPP power' with status 'OK' 2009-Mar-14 21:53:13 LOG5 end_task: Level: (5) ID = <10032> Status = 0 0 0 0 ok 2009-Mar-14 21:53:13 INFO2 wapp_adjpwr: WAPP power: ALFA beam 0: 0.931 0.912 ALFA beam 1: 1.043 1.055 2009-Mar-14 21:53:13 INFO2 wapp_adjpwr: WAPP power: ALFA beam 2: 1.015 0.957 ALFA beam 3: 1.080 1.114 2009-Mar-14 21:53:13 INFO2 wapp_adjpwr: WAPP power: ALFA beam 4: 1.116 0.970 ALFA beam 5: 1.013 0.908 2009-Mar-14 21:53:13 INFO2 wapp_adjpwr: WAPP power: ALFA beam 6: 0.935 0.109 ALFA beam 7: 1.031 0.118 2009-Mar-14 21:53:13 STOP finish_task: Finishing task 'adjusting WAPP power' 2009-Mar-14 21:53:13 LOG5 finish_task: Level: (4) ID = <10031> Status = 0 0 0 0 ok 2009-Mar-14 21:53:13 INFO3 finish_task: DONE finished adjusting: WAPP power 2009-Mar-14 21:53:13 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 21:53:13 STOP end_task: Finishing task 'adjusting WAPP power' with status 'OK' 2009-Mar-14 21:53:13 LOG5 end_task: Level: (4) ID = <10031> Status = 0 0 0 0 ok 2009-Mar-14 21:53:13 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_busy 2009-Mar-14 21:53:13 STOP finish_task: Finishing task 'adjusting WAPP power' 2009-Mar-14 21:53:13 LOG5 finish_task: Level: (3) ID = <10029> Status = 0 0 0 0 ok 2009-Mar-14 21:53:13 INFO2 finish_task: DONE finished adjusting: WAPP power levels 2009-Mar-14 21:53:13 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 21:53:13 STOP end_task: Finishing task 'adjusting WAPP power' with status 'OK' 2009-Mar-14 21:53:13 LOG5 end_task: Level: (3) ID = <10029> Status = 0 0 0 0 ok 2009-Mar-14 21:53:13 INFO3 smartfreq: Taking CAL-OFF at 1380.60607910 MHz ... 2009-Mar-14 21:53:13 LOG4 send_obs_status: To obs_status: <1> PART A1 MESSAGE {Taking CAL-OFF at 1380.60607910 MHz ...} 2009-Mar-14 21:53:13 INFO4 set_smart_frequency: Setting frequency 1380.60607910 MHz 2009-Mar-14 21:53:13 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:53:13 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:53:13 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:53:13 LOG2 antvel: Parameters to Doppler: Topocentric 93193 2009 73 0.0 2009-Mar-14 21:53:13 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:53:14 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1380.60607910 rest0=1380.60607910 rest1=1380.60607910 rest2=1380.60607910 rest3=1380.60607910 rest4=1380.60607910 rest5=1380.60607910 rest6=1380.60607910 rest7=1380.60607910 2009-Mar-14 21:53:14 INFO4 dopset_gen: New sky frequencies: 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 2009-Mar-14 21:53:14 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1380.606079 sky0=1380.606079 sky1=1380.606079 sky2=1380.606079 sky3=1380.606079 sky4=1380.606079 sky5=1380.606079 sky6=1380.606079 sky7=1380.606079 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:53:14 LOG2 dopset_gen: Result from 'sky2syn': 1630.606079 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:53:14 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1630606079.0} 2009-Mar-14 21:53:14 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:53:14 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1380.60607910 MHz}' 2009-Mar-14 21:53:14 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:53:14 LOG5 begin_task: Level: (3) ID = <10033> Status = 0 0 0 0 ok 2009-Mar-14 21:53:14 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1380.60607910 MHz ...} 2009-Mar-14 21:53:14 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.957239 2009.2023599069639 18.999933 2009-Mar-14 21:53:14 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666541 21.899999999999988 2009-Mar-14 21:53:14 LOG4 log_alfabeam: ALFABEAM 1 8.967327567050182 21.794291435859495 2009-Mar-14 21:53:14 LOG4 log_alfabeam: ALFABEAM 2 8.972608144982360 21.858027987615895 2009-Mar-14 21:53:14 LOG4 log_alfabeam: ALFABEAM 3 8.972074953758860 21.963933284031121 2009-Mar-14 21:53:14 LOG4 log_alfabeam: ALFABEAM 4 8.965930006763683 22.005697725510302 2009-Mar-14 21:53:14 LOG4 log_alfabeam: ALFABEAM 5 8.960588534744833 21.939933942041353 2009-Mar-14 21:53:14 LOG4 log_alfabeam: ALFABEAM 6 8.961452411590988 21.834480991065366 2009-Mar-14 21:53:14 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300145 2009-Mar-14 21:53:14 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:53:14 LOG5 begin_task: Level: (4) ID = <10034> Status = 0 0 0 0 ok 2009-Mar-14 21:53:14 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:53:14 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1630606079.0} 2009-Mar-14 21:53:14 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:53:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:14 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6795.00 2009-Mar-14 21:53:14 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1380.60607910 MHz ...} 2009-Mar-14 21:53:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1630.606079 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:53:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:53:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:53:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:53:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:53:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:16 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 21:53:16 LOG4 check_wapp_levels: WAPP-1 power levels: 0.958 0.939 1.075 1.055 2009-Mar-14 21:53:16 LOG4 check_wapp_levels: WAPP-2 power levels: 1.015 0.957 1.080 1.114 2009-Mar-14 21:53:16 LOG4 check_wapp_levels: WAPP-3 power levels: 1.153 0.988 1.074 0.939 2009-Mar-14 21:53:16 LOG4 check_wapp_levels: WAPP-4 power levels: 0.944 0.109 1.042 0.118 2009-Mar-14 21:53:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.153 (still bad) 2009-Mar-14 21:53:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.151 (still bad) 2009-Mar-14 21:53:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.153 (still bad) 2009-Mar-14 21:53:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.156 (still bad) 2009-Mar-14 21:53:25 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:53:25 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:53:25 LOG5 end_task: Level: (4) ID = <10034> Status = 0 0 0 0 ok 2009-Mar-14 21:53:25 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:53:25 LOG5 end_task: Level: (3) ID = <10033> Status = 0 0 0 0 ok 2009-Mar-14 21:53:25 INFO3 smartfreq: Taking CAL-OFF at 1383.34045410 MHz ... 2009-Mar-14 21:53:25 LOG4 send_obs_status: To obs_status: <1> PART A2 MESSAGE {Taking CAL-OFF at 1383.34045410 MHz ...} 2009-Mar-14 21:53:25 INFO4 set_smart_frequency: Setting frequency 1383.34045410 MHz 2009-Mar-14 21:53:25 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:53:25 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:53:25 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:53:25 LOG2 antvel: Parameters to Doppler: Topocentric 93205 2009 73 0.0 2009-Mar-14 21:53:25 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:53:25 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1383.34045410 rest0=1383.34045410 rest1=1383.34045410 rest2=1383.34045410 rest3=1383.34045410 rest4=1383.34045410 rest5=1383.34045410 rest6=1383.34045410 rest7=1383.34045410 2009-Mar-14 21:53:25 INFO4 dopset_gen: New sky frequencies: 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 2009-Mar-14 21:53:25 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1383.340454 sky0=1383.340454 sky1=1383.340454 sky2=1383.340454 sky3=1383.340454 sky4=1383.340454 sky5=1383.340454 sky6=1383.340454 sky7=1383.340454 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:53:25 LOG2 dopset_gen: Result from 'sky2syn': 1633.340454 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:53:25 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1633340454.0} 2009-Mar-14 21:53:25 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:53:25 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1383.34045410 MHz}' 2009-Mar-14 21:53:25 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:53:25 LOG5 begin_task: Level: (3) ID = <10035> Status = 0 0 0 0 ok 2009-Mar-14 21:53:25 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1383.34045410 MHz ...} 2009-Mar-14 21:53:25 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.960581 2009.2023602872209 18.999933 2009-Mar-14 21:53:25 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666534 21.899999999999999 2009-Mar-14 21:53:25 LOG4 log_alfabeam: ALFABEAM 1 8.967429960322260 21.794425263010602 2009-Mar-14 21:53:25 LOG4 log_alfabeam: ALFABEAM 2 8.972648278225616 21.859147536385475 2009-Mar-14 21:53:25 LOG4 log_alfabeam: ALFABEAM 3 8.972012505417128 21.964943150815841 2009-Mar-14 21:53:25 LOG4 log_alfabeam: ALFABEAM 4 8.965827413157141 22.005549625847134 2009-Mar-14 21:53:25 LOG4 log_alfabeam: ALFABEAM 5 8.960550300132615 21.938787105154983 2009-Mar-14 21:53:25 LOG4 log_alfabeam: ALFABEAM 6 8.961516529546714 21.833506384653184 2009-Mar-14 21:53:25 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300146 2009-Mar-14 21:53:26 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:53:26 LOG5 begin_task: Level: (4) ID = <10036> Status = 0 0 0 0 ok 2009-Mar-14 21:53:26 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:53:26 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1633340454.0} 2009-Mar-14 21:53:26 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:53:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.152 (still bad) 2009-Mar-14 21:53:26 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1383.34045410 MHz ...} 2009-Mar-14 21:53:26 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6807.00 2009-Mar-14 21:53:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1633.340454 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:53:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:53:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:53:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:53:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:53:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.148 (still bad) 2009-Mar-14 21:53:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.145 (still bad) 2009-Mar-14 21:53:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.145 (still bad) 2009-Mar-14 21:53:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.147 (still bad) 2009-Mar-14 21:53:36 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.149 (still bad) 2009-Mar-14 21:53:37 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:53:37 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:53:37 LOG5 end_task: Level: (4) ID = <10036> Status = 0 0 0 0 ok 2009-Mar-14 21:53:37 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:53:37 LOG5 end_task: Level: (3) ID = <10035> Status = 0 0 0 0 ok 2009-Mar-14 21:53:37 INFO3 smartfreq: Taking CAL-OFF at 1383.53576660 MHz ... 2009-Mar-14 21:53:37 LOG4 send_obs_status: To obs_status: <1> PART A3 MESSAGE {Taking CAL-OFF at 1383.53576660 MHz ...} 2009-Mar-14 21:53:37 INFO4 set_smart_frequency: Setting frequency 1383.53576660 MHz 2009-Mar-14 21:53:37 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:53:37 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:53:37 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:53:37 LOG2 antvel: Parameters to Doppler: Topocentric 93217 2009 73 0.0 2009-Mar-14 21:53:37 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:53:37 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1383.53576660 rest0=1383.53576660 rest1=1383.53576660 rest2=1383.53576660 rest3=1383.53576660 rest4=1383.53576660 rest5=1383.53576660 rest6=1383.53576660 rest7=1383.53576660 2009-Mar-14 21:53:37 INFO4 dopset_gen: New sky frequencies: 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 2009-Mar-14 21:53:37 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1383.535767 sky0=1383.535767 sky1=1383.535767 sky2=1383.535767 sky3=1383.535767 sky4=1383.535767 sky5=1383.535767 sky6=1383.535767 sky7=1383.535767 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:53:37 LOG2 dopset_gen: Result from 'sky2syn': 1633.535767 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:53:37 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1633535767.0} 2009-Mar-14 21:53:37 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:53:37 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1383.53576660 MHz}' 2009-Mar-14 21:53:37 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:53:37 LOG5 begin_task: Level: (3) ID = <10037> Status = 0 0 0 0 ok 2009-Mar-14 21:53:37 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1383.53576660 MHz ...} 2009-Mar-14 21:53:37 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.963924 2009.2023606674779 18.999933 2009-Mar-14 21:53:37 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666228 21.900000000000006 2009-Mar-14 21:53:37 LOG4 log_alfabeam: ALFABEAM 1 8.967532413757333 21.794578623962401 2009-Mar-14 21:53:37 LOG4 log_alfabeam: ALFABEAM 2 8.972687407641931 21.860276821359875 2009-Mar-14 21:53:37 LOG4 log_alfabeam: ALFABEAM 3 8.971948944905627 21.965943209751135 2009-Mar-14 21:53:37 LOG4 log_alfabeam: ALFABEAM 4 8.965724786980990 22.005381923445348 2009-Mar-14 21:53:37 LOG4 log_alfabeam: ALFABEAM 5 8.960513126080572 21.937631184706479 2009-Mar-14 21:53:37 LOG4 log_alfabeam: ALFABEAM 6 8.961581692553755 21.832542260323915 2009-Mar-14 21:53:37 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300147 2009-Mar-14 21:53:38 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:53:38 LOG5 begin_task: Level: (4) ID = <10038> Status = 0 0 0 0 ok 2009-Mar-14 21:53:38 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:53:38 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1633535767.0} 2009-Mar-14 21:53:38 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:53:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:38 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1383.53576660 MHz ...} 2009-Mar-14 21:53:38 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6819.00 2009-Mar-14 21:53:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.144 (still bad) 2009-Mar-14 21:53:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1633.535767 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:53:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:53:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:53:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:53:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:53:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.142 (still bad) 2009-Mar-14 21:53:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.141 (still bad) 2009-Mar-14 21:53:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.140 (still bad) 2009-Mar-14 21:53:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.140 (still bad) 2009-Mar-14 21:53:49 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.141 (still bad) 2009-Mar-14 21:53:49 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:53:49 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:53:49 LOG5 end_task: Level: (4) ID = <10038> Status = 0 0 0 0 ok 2009-Mar-14 21:53:49 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:53:49 LOG5 end_task: Level: (3) ID = <10037> Status = 0 0 0 0 ok 2009-Mar-14 21:53:49 INFO3 smartfreq: Taking CAL-OFF at 1384.12170410 MHz ... 2009-Mar-14 21:53:49 LOG4 send_obs_status: To obs_status: <1> PART A4 MESSAGE {Taking CAL-OFF at 1384.12170410 MHz ...} 2009-Mar-14 21:53:49 INFO4 set_smart_frequency: Setting frequency 1384.12170410 MHz 2009-Mar-14 21:53:49 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:53:49 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:53:49 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:53:49 LOG2 antvel: Parameters to Doppler: Topocentric 93229 2009 73 0.0 2009-Mar-14 21:53:49 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:53:49 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1384.12170410 rest0=1384.12170410 rest1=1384.12170410 rest2=1384.12170410 rest3=1384.12170410 rest4=1384.12170410 rest5=1384.12170410 rest6=1384.12170410 rest7=1384.12170410 2009-Mar-14 21:53:49 INFO4 dopset_gen: New sky frequencies: 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 2009-Mar-14 21:53:49 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1384.121704 sky0=1384.121704 sky1=1384.121704 sky2=1384.121704 sky3=1384.121704 sky4=1384.121704 sky5=1384.121704 sky6=1384.121704 sky7=1384.121704 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:53:49 LOG2 dopset_gen: Result from 'sky2syn': 1634.121704 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:53:49 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1634121704.0} 2009-Mar-14 21:53:49 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:53:49 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1384.12170410 MHz}' 2009-Mar-14 21:53:49 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:53:49 LOG5 begin_task: Level: (3) ID = <10039> Status = 0 0 0 0 ok 2009-Mar-14 21:53:49 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1384.12170410 MHz ...} 2009-Mar-14 21:53:49 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.967266 2009.2023610477349 18.999933 2009-Mar-14 21:53:49 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666567 21.899999999999999 2009-Mar-14 21:53:49 LOG4 log_alfabeam: ALFABEAM 1 8.967634810888612 21.794751430287537 2009-Mar-14 21:53:49 LOG4 log_alfabeam: ALFABEAM 2 8.972725483883110 21.861414603865331 2009-Mar-14 21:53:49 LOG4 log_alfabeam: ALFABEAM 3 8.971884339521703 21.966932270026092 2009-Mar-14 21:53:49 LOG4 log_alfabeam: ALFABEAM 4 8.965622245112444 22.005194730511398 2009-Mar-14 21:53:49 LOG4 log_alfabeam: ALFABEAM 5 8.960477058898952 21.936467466860339 2009-Mar-14 21:53:49 LOG4 log_alfabeam: ALFABEAM 6 8.961647830340416 21.831589751448636 2009-Mar-14 21:53:49 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300148 2009-Mar-14 21:53:50 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:53:50 LOG5 begin_task: Level: (4) ID = <10040> Status = 0 0 0 0 ok 2009-Mar-14 21:53:50 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:53:50 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1634121704.0} 2009-Mar-14 21:53:50 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:53:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:53:50 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1384.12170410 MHz ...} 2009-Mar-14 21:53:50 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6831.00 2009-Mar-14 21:53:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.139 (still bad) 2009-Mar-14 21:53:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1634.121704 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:53:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:53:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:53:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:53:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:53:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:53:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.129 (still bad) 2009-Mar-14 21:53:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.132 (still bad) 2009-Mar-14 21:53:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.130 (still bad) 2009-Mar-14 21:53:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.131 (still bad) 2009-Mar-14 21:54:01 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:54:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.130 (still bad) 2009-Mar-14 21:54:01 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:54:01 LOG5 end_task: Level: (4) ID = <10040> Status = 0 0 0 0 ok 2009-Mar-14 21:54:01 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:54:01 LOG5 end_task: Level: (3) ID = <10039> Status = 0 0 0 0 ok 2009-Mar-14 21:54:01 INFO3 smartfreq: Taking CAL-OFF at 1385.29357910 MHz ... 2009-Mar-14 21:54:01 LOG4 send_obs_status: To obs_status: <1> PART A5 MESSAGE {Taking CAL-OFF at 1385.29357910 MHz ...} 2009-Mar-14 21:54:01 INFO4 set_smart_frequency: Setting frequency 1385.29357910 MHz 2009-Mar-14 21:54:01 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:54:01 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:54:01 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:54:01 LOG2 antvel: Parameters to Doppler: Topocentric 93241 2009 73 0.0 2009-Mar-14 21:54:01 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:54:01 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1385.29357910 rest0=1385.29357910 rest1=1385.29357910 rest2=1385.29357910 rest3=1385.29357910 rest4=1385.29357910 rest5=1385.29357910 rest6=1385.29357910 rest7=1385.29357910 2009-Mar-14 21:54:01 INFO4 dopset_gen: New sky frequencies: 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 2009-Mar-14 21:54:01 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1385.293579 sky0=1385.293579 sky1=1385.293579 sky2=1385.293579 sky3=1385.293579 sky4=1385.293579 sky5=1385.293579 sky6=1385.293579 sky7=1385.293579 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:54:01 LOG2 dopset_gen: Result from 'sky2syn': 1635.293579 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:54:01 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635293579.0} 2009-Mar-14 21:54:01 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:54:01 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1385.29357910 MHz}' 2009-Mar-14 21:54:01 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:54:01 LOG5 begin_task: Level: (3) ID = <10041> Status = 0 0 0 0 ok 2009-Mar-14 21:54:01 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1385.29357910 MHz ...} 2009-Mar-14 21:54:01 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.970608 2009.2023614279922 18.999933 2009-Mar-14 21:54:01 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666727 21.899999999999988 2009-Mar-14 21:54:01 LOG4 log_alfabeam: ALFABEAM 1 8.967737127027489 21.794943697098617 2009-Mar-14 21:54:01 LOG4 log_alfabeam: ALFABEAM 2 8.972762494426604 21.862560640968820 2009-Mar-14 21:54:01 LOG4 log_alfabeam: ALFABEAM 3 8.971818701508274 21.967910054656091 2009-Mar-14 21:54:01 LOG4 log_alfabeam: ALFABEAM 4 8.965519812430406 22.004988043029332 2009-Mar-14 21:54:01 LOG4 log_alfabeam: ALFABEAM 5 8.960442109688509 21.935296216694226 2009-Mar-14 21:54:01 LOG4 log_alfabeam: ALFABEAM 6 8.961714929296090 21.830649108199406 2009-Mar-14 21:54:01 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300149 2009-Mar-14 21:54:02 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:54:02 LOG5 begin_task: Level: (4) ID = <10042> Status = 0 0 0 0 ok 2009-Mar-14 21:54:02 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:54:02 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635293579.0} 2009-Mar-14 21:54:02 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:54:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:54:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:54:02 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1385.29357910 MHz ...} 2009-Mar-14 21:54:02 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6843.00 2009-Mar-14 21:54:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.130 (still bad) 2009-Mar-14 21:54:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.293579 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:54:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:54:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:54:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:54:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:54:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 21:54:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 21:54:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 21:54:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 21:54:13 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:54:13 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:54:13 LOG5 end_task: Level: (4) ID = <10042> Status = 0 0 0 0 ok 2009-Mar-14 21:54:13 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:54:13 LOG5 end_task: Level: (3) ID = <10041> Status = 0 0 0 0 ok 2009-Mar-14 21:54:13 INFO3 smartfreq: Taking CAL-OFF at 1385.68420410 MHz ... 2009-Mar-14 21:54:13 LOG4 send_obs_status: To obs_status: <1> PART A6 MESSAGE {Taking CAL-OFF at 1385.68420410 MHz ...} 2009-Mar-14 21:54:13 INFO4 set_smart_frequency: Setting frequency 1385.68420410 MHz 2009-Mar-14 21:54:13 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:54:13 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:54:13 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:54:13 LOG2 antvel: Parameters to Doppler: Topocentric 93253 2009 73 0.0 2009-Mar-14 21:54:13 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:54:13 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1385.68420410 rest0=1385.68420410 rest1=1385.68420410 rest2=1385.68420410 rest3=1385.68420410 rest4=1385.68420410 rest5=1385.68420410 rest6=1385.68420410 rest7=1385.68420410 2009-Mar-14 21:54:13 INFO4 dopset_gen: New sky frequencies: 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 2009-Mar-14 21:54:13 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1385.684204 sky0=1385.684204 sky1=1385.684204 sky2=1385.684204 sky3=1385.684204 sky4=1385.684204 sky5=1385.684204 sky6=1385.684204 sky7=1385.684204 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:54:13 LOG2 dopset_gen: Result from 'sky2syn': 1635.684204 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:54:13 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635684204.0} 2009-Mar-14 21:54:13 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:54:13 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1385.68420410 MHz}' 2009-Mar-14 21:54:13 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:54:13 LOG5 begin_task: Level: (3) ID = <10043> Status = 0 0 0 0 ok 2009-Mar-14 21:54:13 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1385.68420410 MHz ...} 2009-Mar-14 21:54:13 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.973951 2009.2023618082492 18.999933 2009-Mar-14 21:54:13 LOG4 log_alfabeam: ALFABEAM 0 8.966666666665677 21.899999999999991 2009-Mar-14 21:54:13 LOG4 log_alfabeam: ALFABEAM 1 8.967839337359623 21.795155431518946 2009-Mar-14 21:54:13 LOG4 log_alfabeam: ALFABEAM 2 8.972798427102170 21.863714684634335 2009-Mar-14 21:54:13 LOG4 log_alfabeam: ALFABEAM 3 8.971752043631257 21.968876289509492 2009-Mar-14 21:54:13 LOG4 log_alfabeam: ALFABEAM 4 8.965417513902585 22.004761865059741 2009-Mar-14 21:54:13 LOG4 log_alfabeam: ALFABEAM 5 8.960408289136080 21.934117703801125 2009-Mar-14 21:54:13 LOG4 log_alfabeam: ALFABEAM 6 8.961782975266285 21.829720577194081 2009-Mar-14 21:54:13 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300150 2009-Mar-14 21:54:14 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:54:14 LOG5 begin_task: Level: (4) ID = <10044> Status = 0 0 0 0 ok 2009-Mar-14 21:54:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 21:54:14 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:54:14 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635684204.0} 2009-Mar-14 21:54:14 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:54:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:54:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:54:14 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1385.68420410 MHz ...} 2009-Mar-14 21:54:14 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6855.00 2009-Mar-14 21:54:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.684204 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:54:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:54:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:54:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:54:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:54:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 21:54:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:18 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 21:54:18 LOG4 check_wapp_levels: WAPP-1 power levels: 0.926 0.913 1.035 1.051 2009-Mar-14 21:54:18 LOG4 check_wapp_levels: WAPP-2 power levels: 1.017 0.952 1.087 1.110 2009-Mar-14 21:54:18 LOG4 check_wapp_levels: WAPP-3 power levels: 1.106 0.970 1.004 0.904 2009-Mar-14 21:54:18 LOG4 check_wapp_levels: WAPP-4 power levels: 0.934 0.109 1.031 0.118 2009-Mar-14 21:54:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 21:54:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 21:54:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 21:54:25 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:54:25 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:54:25 LOG5 end_task: Level: (4) ID = <10044> Status = 0 0 0 0 ok 2009-Mar-14 21:54:25 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:54:25 LOG5 end_task: Level: (3) ID = <10043> Status = 0 0 0 0 ok 2009-Mar-14 21:54:25 INFO3 smartfreq: Taking CAL-OFF at 1386.66076660 MHz ... 2009-Mar-14 21:54:25 LOG4 send_obs_status: To obs_status: <1> PART A7 MESSAGE {Taking CAL-OFF at 1386.66076660 MHz ...} 2009-Mar-14 21:54:25 INFO4 set_smart_frequency: Setting frequency 1386.66076660 MHz 2009-Mar-14 21:54:25 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:54:25 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:54:25 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:54:25 LOG2 antvel: Parameters to Doppler: Topocentric 93265 2009 73 0.0 2009-Mar-14 21:54:25 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:54:25 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1386.66076660 rest0=1386.66076660 rest1=1386.66076660 rest2=1386.66076660 rest3=1386.66076660 rest4=1386.66076660 rest5=1386.66076660 rest6=1386.66076660 rest7=1386.66076660 2009-Mar-14 21:54:25 INFO4 dopset_gen: New sky frequencies: 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 2009-Mar-14 21:54:25 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1386.660767 sky0=1386.660767 sky1=1386.660767 sky2=1386.660767 sky3=1386.660767 sky4=1386.660767 sky5=1386.660767 sky6=1386.660767 sky7=1386.660767 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:54:25 LOG2 dopset_gen: Result from 'sky2syn': 1636.660767 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:54:25 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1636660767.0} 2009-Mar-14 21:54:25 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:54:25 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1386.66076660 MHz}' 2009-Mar-14 21:54:25 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:54:25 LOG5 begin_task: Level: (3) ID = <10045> Status = 0 0 0 0 ok 2009-Mar-14 21:54:25 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1386.66076660 MHz ...} 2009-Mar-14 21:54:25 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.977293 2009.2023621885062 18.999933 2009-Mar-14 21:54:25 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666221 21.899999999999991 2009-Mar-14 21:54:25 LOG4 log_alfabeam: ALFABEAM 1 8.967941325489923 21.795386416521080 2009-Mar-14 21:54:25 LOG4 log_alfabeam: ALFABEAM 2 8.972833239355026 21.864875436513376 2009-Mar-14 21:54:25 LOG4 log_alfabeam: ALFABEAM 3 8.971684440311968 21.969829852976865 2009-Mar-14 21:54:25 LOG4 log_alfabeam: ALFABEAM 4 8.965315466140638 22.004516437853621 2009-Mar-14 21:54:25 LOG4 log_alfabeam: ALFABEAM 5 8.960375636317183 21.932933268377496 2009-Mar-14 21:54:25 LOG4 log_alfabeam: ALFABEAM 6 8.961851891493177 21.828805217334832 2009-Mar-14 21:54:25 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300151 2009-Mar-14 21:54:26 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:54:26 LOG5 begin_task: Level: (4) ID = <10046> Status = 0 0 0 0 ok 2009-Mar-14 21:54:26 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:54:26 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1636660767.0} 2009-Mar-14 21:54:26 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:54:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:54:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:54:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 21:54:26 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1386.66076660 MHz ...} 2009-Mar-14 21:54:26 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6867.00 2009-Mar-14 21:54:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1636.660767 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:54:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:54:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:54:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:54:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:54:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 21:54:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 21:54:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 21:54:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 21:54:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 21:54:37 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:54:37 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:54:37 LOG5 end_task: Level: (4) ID = <10046> Status = 0 0 0 0 ok 2009-Mar-14 21:54:37 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:54:37 LOG5 end_task: Level: (3) ID = <10045> Status = 0 0 0 0 ok 2009-Mar-14 21:54:37 LOG4 send_obs_status: To obs_status: <1> BITMAP stat_cal_on INFO {Making 7 CAL-ONs} MESSAGE {Setting CAL-ON ...} 2009-Mar-14 21:54:37 LOG3 wapp_calcontrol: To CALCONTROL: CALON 2009-Mar-14 21:54:37 LOG3 sock_errsend: To CALCONTROL: CALON STATUS 2009-Mar-14 21:54:37 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 21:54:37 LOG5 begin_task: Level: (3) ID = <10047> Status = 0 0 0 0 ok 2009-Mar-14 21:54:37 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 21:54:37 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x03 2009-Mar-14 21:54:37 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 21:54:37 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 21:54:37 LOG5 end_task: Level: (3) ID = <10047> Status = 0 0 0 0 ok 2009-Mar-14 21:54:37 INFO3 smartfreq: Taking CAL-ON at 1380.60607910 MHz ... 2009-Mar-14 21:54:37 LOG4 send_obs_status: To obs_status: <1> PART B1 MESSAGE {Taking CAL-ON at 1380.60607910 MHz ...} 2009-Mar-14 21:54:37 INFO4 set_smart_frequency: Setting frequency 1380.60607910 MHz 2009-Mar-14 21:54:37 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:54:37 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:54:37 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:54:37 LOG2 antvel: Parameters to Doppler: Topocentric 93277 2009 73 0.0 2009-Mar-14 21:54:37 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:54:37 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1380.60607910 rest0=1380.60607910 rest1=1380.60607910 rest2=1380.60607910 rest3=1380.60607910 rest4=1380.60607910 rest5=1380.60607910 rest6=1380.60607910 rest7=1380.60607910 2009-Mar-14 21:54:37 INFO4 dopset_gen: New sky frequencies: 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 2009-Mar-14 21:54:37 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1380.606079 sky0=1380.606079 sky1=1380.606079 sky2=1380.606079 sky3=1380.606079 sky4=1380.606079 sky5=1380.606079 sky6=1380.606079 sky7=1380.606079 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:54:37 LOG2 dopset_gen: Result from 'sky2syn': 1630.606079 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:54:37 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1630606079.0} 2009-Mar-14 21:54:37 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:54:37 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1380.60607910 MHz}' 2009-Mar-14 21:54:37 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:54:37 LOG5 begin_task: Level: (3) ID = <10048> Status = 0 0 0 0 ok 2009-Mar-14 21:54:37 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1380.60607910 MHz ...} 2009-Mar-14 21:54:37 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.980636 2009.2023625687632 18.999933 2009-Mar-14 21:54:37 LOG4 log_alfabeam: ALFABEAM 0 8.966666666667420 21.900000000000016 2009-Mar-14 21:54:37 LOG4 log_alfabeam: ALFABEAM 1 8.968043097443942 21.795636668886281 2009-Mar-14 21:54:37 LOG4 log_alfabeam: ALFABEAM 2 8.972866932701562 21.866042971245506 2009-Mar-14 21:54:37 LOG4 log_alfabeam: ALFABEAM 3 8.971615887227452 21.970770791410850 2009-Mar-14 21:54:37 LOG4 log_alfabeam: ALFABEAM 4 8.965213663109360 22.004251751592026 2009-Mar-14 21:54:37 LOG4 log_alfabeam: ALFABEAM 5 8.960344148662157 21.931742847168703 2009-Mar-14 21:54:37 LOG4 log_alfabeam: ALFABEAM 6 8.961921681639661 21.827902963835122 2009-Mar-14 21:54:37 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300152 2009-Mar-14 21:54:38 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:54:38 LOG5 begin_task: Level: (4) ID = <10049> Status = 0 0 0 0 ok 2009-Mar-14 21:54:38 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:54:38 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1630606079.0} 2009-Mar-14 21:54:38 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:54:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:54:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:54:38 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1380.60607910 MHz ...} 2009-Mar-14 21:54:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 21:54:38 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6879.00 2009-Mar-14 21:54:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1630.606079 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:54:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:54:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:54:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:54:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:54:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.626 (still bad) 2009-Mar-14 21:54:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.630 (still bad) 2009-Mar-14 21:54:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.627 (still bad) 2009-Mar-14 21:54:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.631 (still bad) 2009-Mar-14 21:54:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.632 (still bad) 2009-Mar-14 21:54:49 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:54:49 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:54:49 LOG5 end_task: Level: (4) ID = <10049> Status = 0 0 0 0 ok 2009-Mar-14 21:54:49 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:54:49 LOG5 end_task: Level: (3) ID = <10048> Status = 0 0 0 0 ok 2009-Mar-14 21:54:49 INFO3 smartfreq: Taking CAL-ON at 1383.34045410 MHz ... 2009-Mar-14 21:54:49 LOG4 send_obs_status: To obs_status: <1> PART B2 MESSAGE {Taking CAL-ON at 1383.34045410 MHz ...} 2009-Mar-14 21:54:49 INFO4 set_smart_frequency: Setting frequency 1383.34045410 MHz 2009-Mar-14 21:54:49 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:54:49 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:54:49 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:54:49 LOG2 antvel: Parameters to Doppler: Topocentric 93289 2009 73 0.0 2009-Mar-14 21:54:49 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:54:49 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1383.34045410 rest0=1383.34045410 rest1=1383.34045410 rest2=1383.34045410 rest3=1383.34045410 rest4=1383.34045410 rest5=1383.34045410 rest6=1383.34045410 rest7=1383.34045410 2009-Mar-14 21:54:49 INFO4 dopset_gen: New sky frequencies: 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 2009-Mar-14 21:54:49 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1383.340454 sky0=1383.340454 sky1=1383.340454 sky2=1383.340454 sky3=1383.340454 sky4=1383.340454 sky5=1383.340454 sky6=1383.340454 sky7=1383.340454 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:54:49 LOG2 dopset_gen: Result from 'sky2syn': 1633.340454 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:54:49 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1633340454.0} 2009-Mar-14 21:54:49 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:54:49 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1383.34045410 MHz}' 2009-Mar-14 21:54:49 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:54:49 LOG5 begin_task: Level: (3) ID = <10050> Status = 0 0 0 0 ok 2009-Mar-14 21:54:49 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1383.34045410 MHz ...} 2009-Mar-14 21:54:49 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.983978 2009.2023629490202 18.999933 2009-Mar-14 21:54:49 LOG4 log_alfabeam: ALFABEAM 0 8.966666666667313 21.900000000000009 2009-Mar-14 21:54:49 LOG4 log_alfabeam: ALFABEAM 1 8.968144537777352 21.795905886768644 2009-Mar-14 21:54:49 LOG4 log_alfabeam: ALFABEAM 2 8.972899469490832 21.867215960397306 2009-Mar-14 21:54:49 LOG4 log_alfabeam: ALFABEAM 3 8.971546463016054 21.971698038665529 2009-Mar-14 21:54:49 LOG4 log_alfabeam: ALFABEAM 4 8.965112220288120 22.003968132316082 2009-Mar-14 21:54:49 LOG4 log_alfabeam: ALFABEAM 5 8.960313860073777 21.930547806096168 2009-Mar-14 21:54:49 LOG4 log_alfabeam: ALFABEAM 6 8.961992265087934 21.827014817436318 2009-Mar-14 21:54:49 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300153 2009-Mar-14 21:54:50 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:54:50 LOG5 begin_task: Level: (4) ID = <10051> Status = 0 0 0 0 ok 2009-Mar-14 21:54:50 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:54:50 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1633340454.0} 2009-Mar-14 21:54:50 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:54:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:54:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:54:50 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1383.34045410 MHz ...} 2009-Mar-14 21:54:50 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6891.00 2009-Mar-14 21:54:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.631 (still bad) 2009-Mar-14 21:54:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1633.340454 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:54:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:54:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:54:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:54:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:54:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:54:53 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.622 (still bad) 2009-Mar-14 21:54:55 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.620 (still bad) 2009-Mar-14 21:54:57 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.620 (still bad) 2009-Mar-14 21:54:59 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.620 (still bad) 2009-Mar-14 21:55:01 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.620 (still bad) 2009-Mar-14 21:55:01 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:55:01 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:55:01 LOG5 end_task: Level: (4) ID = <10051> Status = 0 0 0 0 ok 2009-Mar-14 21:55:01 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:55:01 LOG5 end_task: Level: (3) ID = <10050> Status = 0 0 0 0 ok 2009-Mar-14 21:55:01 INFO3 smartfreq: Taking CAL-ON at 1383.53576660 MHz ... 2009-Mar-14 21:55:01 LOG4 send_obs_status: To obs_status: <1> PART B3 MESSAGE {Taking CAL-ON at 1383.53576660 MHz ...} 2009-Mar-14 21:55:01 INFO4 set_smart_frequency: Setting frequency 1383.53576660 MHz 2009-Mar-14 21:55:01 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:55:01 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:55:01 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:55:01 LOG2 antvel: Parameters to Doppler: Topocentric 93301 2009 73 0.0 2009-Mar-14 21:55:01 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:55:01 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1383.53576660 rest0=1383.53576660 rest1=1383.53576660 rest2=1383.53576660 rest3=1383.53576660 rest4=1383.53576660 rest5=1383.53576660 rest6=1383.53576660 rest7=1383.53576660 2009-Mar-14 21:55:01 INFO4 dopset_gen: New sky frequencies: 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 2009-Mar-14 21:55:01 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1383.535767 sky0=1383.535767 sky1=1383.535767 sky2=1383.535767 sky3=1383.535767 sky4=1383.535767 sky5=1383.535767 sky6=1383.535767 sky7=1383.535767 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:55:01 LOG2 dopset_gen: Result from 'sky2syn': 1633.535767 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:55:01 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1633535767.0} 2009-Mar-14 21:55:01 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:55:01 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1383.53576660 MHz}' 2009-Mar-14 21:55:01 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:55:01 LOG5 begin_task: Level: (3) ID = <10052> Status = 0 0 0 0 ok 2009-Mar-14 21:55:01 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1383.53576660 MHz ...} 2009-Mar-14 21:55:01 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.987321 2009.2023633292774 18.999933 2009-Mar-14 21:55:01 LOG4 log_alfabeam: ALFABEAM 0 8.966666666667104 21.899999999999999 2009-Mar-14 21:55:01 LOG4 log_alfabeam: ALFABEAM 1 8.968245653181556 21.796194048811767 2009-Mar-14 21:55:01 LOG4 log_alfabeam: ALFABEAM 2 8.972930853545467 21.868394467270388 2009-Mar-14 21:55:01 LOG4 log_alfabeam: ALFABEAM 3 8.971476165142866 21.972611668453442 2009-Mar-14 21:55:01 LOG4 log_alfabeam: ALFABEAM 4 8.965011130926376 22.003665608234876 2009-Mar-14 21:55:01 LOG4 log_alfabeam: ALFABEAM 5 8.960284765553444 21.929348090631660 2009-Mar-14 21:55:01 LOG4 log_alfabeam: ALFABEAM 6 8.962063643977897 21.826140684720247 2009-Mar-14 21:55:01 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300154 2009-Mar-14 21:55:02 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:55:02 LOG5 begin_task: Level: (4) ID = <10053> Status = 0 0 0 0 ok 2009-Mar-14 21:55:02 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1633535767.0} 2009-Mar-14 21:55:02 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 15 (99999966 != 99999964 diff = 2)! 2009-Mar-14 21:55:02 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:55:02 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:55:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:55:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:55:02 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1383.53576660 MHz ...} 2009-Mar-14 21:55:02 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6903.00 2009-Mar-14 21:55:03 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.618 (still bad) 2009-Mar-14 21:55:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1633.535767 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:55:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:55:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:55:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:55:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:55:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:05 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.613 (still bad) 2009-Mar-14 21:55:07 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.615 (still bad) 2009-Mar-14 21:55:09 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.617 (still bad) 2009-Mar-14 21:55:11 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.614 (still bad) 2009-Mar-14 21:55:13 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:55:13 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.616 (still bad) 2009-Mar-14 21:55:13 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:55:13 LOG5 end_task: Level: (4) ID = <10053> Status = 0 0 0 0 ok 2009-Mar-14 21:55:13 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:55:13 LOG5 end_task: Level: (3) ID = <10052> Status = 0 0 0 0 ok 2009-Mar-14 21:55:13 INFO3 smartfreq: Taking CAL-ON at 1384.12170410 MHz ... 2009-Mar-14 21:55:13 LOG4 send_obs_status: To obs_status: <1> PART B4 MESSAGE {Taking CAL-ON at 1384.12170410 MHz ...} 2009-Mar-14 21:55:13 INFO4 set_smart_frequency: Setting frequency 1384.12170410 MHz 2009-Mar-14 21:55:13 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:55:13 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:55:13 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:55:13 LOG2 antvel: Parameters to Doppler: Topocentric 93313 2009 73 0.0 2009-Mar-14 21:55:13 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:55:13 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1384.12170410 rest0=1384.12170410 rest1=1384.12170410 rest2=1384.12170410 rest3=1384.12170410 rest4=1384.12170410 rest5=1384.12170410 rest6=1384.12170410 rest7=1384.12170410 2009-Mar-14 21:55:13 INFO4 dopset_gen: New sky frequencies: 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 2009-Mar-14 21:55:13 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1384.121704 sky0=1384.121704 sky1=1384.121704 sky2=1384.121704 sky3=1384.121704 sky4=1384.121704 sky5=1384.121704 sky6=1384.121704 sky7=1384.121704 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:55:13 LOG2 dopset_gen: Result from 'sky2syn': 1634.121704 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:55:13 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1634121704.0} 2009-Mar-14 21:55:13 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:55:13 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1384.12170410 MHz}' 2009-Mar-14 21:55:13 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:55:13 LOG5 begin_task: Level: (3) ID = <10054> Status = 0 0 0 0 ok 2009-Mar-14 21:55:13 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1384.12170410 MHz ...} 2009-Mar-14 21:55:13 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.990663 2009.2023637095344 18.999933 2009-Mar-14 21:55:13 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666761 21.899999999999999 2009-Mar-14 21:55:13 LOG4 log_alfabeam: ALFABEAM 1 8.968346329876983 21.796500770549642 2009-Mar-14 21:55:13 LOG4 log_alfabeam: ALFABEAM 2 8.972961052341830 21.869577141656656 2009-Mar-14 21:55:13 LOG4 log_alfabeam: ALFABEAM 3 8.971405075947906 21.973510676626887 2009-Mar-14 21:55:13 LOG4 log_alfabeam: ALFABEAM 4 8.964910508668167 22.003344587721788 2009-Mar-14 21:55:13 LOG4 log_alfabeam: ALFABEAM 5 8.960256893660414 21.928145083726886 2009-Mar-14 21:55:13 LOG4 log_alfabeam: ALFABEAM 6 8.962135734417148 21.825281502447172 2009-Mar-14 21:55:13 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300155 2009-Mar-14 21:55:14 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:55:14 LOG5 begin_task: Level: (4) ID = <10055> Status = 0 0 0 0 ok 2009-Mar-14 21:55:14 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:55:14 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1634121704.0} 2009-Mar-14 21:55:14 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:55:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:55:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:55:14 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1384.12170410 MHz ...} 2009-Mar-14 21:55:14 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6915.00 2009-Mar-14 21:55:15 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.616 (still bad) 2009-Mar-14 21:55:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1634.121704 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:55:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:55:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:55:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:55:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:55:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.603 (still bad) 2009-Mar-14 21:55:19 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 21:55:19 LOG4 check_wapp_levels: WAPP-1 power levels: 1.317 1.267 1.457 1.461 2009-Mar-14 21:55:19 LOG4 check_wapp_levels: WAPP-2 power levels: 1.434 1.346 1.560 1.557 2009-Mar-14 21:55:19 LOG4 check_wapp_levels: WAPP-3 power levels: 1.599 1.381 1.459 1.237 2009-Mar-14 21:55:19 LOG4 check_wapp_levels: WAPP-4 power levels: 1.348 0.109 1.487 0.119 2009-Mar-14 21:55:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.600 (still bad) 2009-Mar-14 21:55:23 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.607 (still bad) 2009-Mar-14 21:55:25 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:55:25 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:55:25 LOG5 end_task: Level: (4) ID = <10055> Status = 0 0 0 0 ok 2009-Mar-14 21:55:25 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:55:25 LOG5 end_task: Level: (3) ID = <10054> Status = 0 0 0 0 ok 2009-Mar-14 21:55:25 INFO3 smartfreq: Taking CAL-ON at 1385.29357910 MHz ... 2009-Mar-14 21:55:25 LOG4 send_obs_status: To obs_status: <1> PART B5 MESSAGE {Taking CAL-ON at 1385.29357910 MHz ...} 2009-Mar-14 21:55:25 INFO4 set_smart_frequency: Setting frequency 1385.29357910 MHz 2009-Mar-14 21:55:25 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:55:25 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:55:25 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:55:25 LOG2 antvel: Parameters to Doppler: Topocentric 93325 2009 73 0.0 2009-Mar-14 21:55:25 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:55:25 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1385.29357910 rest0=1385.29357910 rest1=1385.29357910 rest2=1385.29357910 rest3=1385.29357910 rest4=1385.29357910 rest5=1385.29357910 rest6=1385.29357910 rest7=1385.29357910 2009-Mar-14 21:55:25 INFO4 dopset_gen: New sky frequencies: 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 2009-Mar-14 21:55:25 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1385.293579 sky0=1385.293579 sky1=1385.293579 sky2=1385.293579 sky3=1385.293579 sky4=1385.293579 sky5=1385.293579 sky6=1385.293579 sky7=1385.293579 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:55:25 LOG2 dopset_gen: Result from 'sky2syn': 1635.293579 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:55:25 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635293579.0} 2009-Mar-14 21:55:25 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:55:25 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1385.29357910 MHz}' 2009-Mar-14 21:55:25 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:55:25 LOG5 begin_task: Level: (3) ID = <10056> Status = 0 0 0 0 ok 2009-Mar-14 21:55:25 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1385.29357910 MHz ...} 2009-Mar-14 21:55:25 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.994006 2009.2023640897914 18.999933 2009-Mar-14 21:55:25 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666868 21.900000000000006 2009-Mar-14 21:55:25 LOG4 log_alfabeam: ALFABEAM 1 8.968446575655982 21.796825994423070 2009-Mar-14 21:55:25 LOG4 log_alfabeam: ALFABEAM 2 8.972990072117859 21.870764040936312 2009-Mar-14 21:55:25 LOG4 log_alfabeam: ALFABEAM 3 8.971333194352157 21.974395168032434 2009-Mar-14 21:55:25 LOG4 log_alfabeam: ALFABEAM 4 8.964810345574962 22.003005134895790 2009-Mar-14 21:55:25 LOG4 log_alfabeam: ALFABEAM 5 8.960230236883801 21.926938733928328 2009-Mar-14 21:55:25 LOG4 log_alfabeam: ALFABEAM 6 8.962208537353956 21.824437145318853 2009-Mar-14 21:55:25 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300156 2009-Mar-14 21:55:26 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:55:26 LOG5 begin_task: Level: (4) ID = <10057> Status = 0 0 0 0 ok 2009-Mar-14 21:55:26 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:55:26 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635293579.0} 2009-Mar-14 21:55:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.600 (still bad) 2009-Mar-14 21:55:26 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:55:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:55:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:55:26 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1385.29357910 MHz ...} 2009-Mar-14 21:55:26 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6927.00 2009-Mar-14 21:55:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.293579 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:55:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:55:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:55:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:55:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:55:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.600 (still bad) 2009-Mar-14 21:55:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.573 (still bad) 2009-Mar-14 21:55:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.569 (still bad) 2009-Mar-14 21:55:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.569 (still bad) 2009-Mar-14 21:55:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.577 (still bad) 2009-Mar-14 21:55:37 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:55:37 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:55:37 LOG5 end_task: Level: (4) ID = <10057> Status = 0 0 0 0 ok 2009-Mar-14 21:55:37 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:55:37 LOG5 end_task: Level: (3) ID = <10056> Status = 0 0 0 0 ok 2009-Mar-14 21:55:37 INFO3 smartfreq: Taking CAL-ON at 1385.68420410 MHz ... 2009-Mar-14 21:55:37 LOG4 send_obs_status: To obs_status: <1> PART B6 MESSAGE {Taking CAL-ON at 1385.68420410 MHz ...} 2009-Mar-14 21:55:37 INFO4 set_smart_frequency: Setting frequency 1385.68420410 MHz 2009-Mar-14 21:55:37 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:55:37 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:55:37 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:55:37 LOG2 antvel: Parameters to Doppler: Topocentric 93337 2009 73 0.0 2009-Mar-14 21:55:37 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:55:37 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1385.68420410 rest0=1385.68420410 rest1=1385.68420410 rest2=1385.68420410 rest3=1385.68420410 rest4=1385.68420410 rest5=1385.68420410 rest6=1385.68420410 rest7=1385.68420410 2009-Mar-14 21:55:37 INFO4 dopset_gen: New sky frequencies: 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 2009-Mar-14 21:55:37 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1385.684204 sky0=1385.684204 sky1=1385.684204 sky2=1385.684204 sky3=1385.684204 sky4=1385.684204 sky5=1385.684204 sky6=1385.684204 sky7=1385.684204 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:55:37 LOG2 dopset_gen: Result from 'sky2syn': 1635.684204 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:55:37 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635684204.0} 2009-Mar-14 21:55:37 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:55:37 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1385.68420410 MHz}' 2009-Mar-14 21:55:37 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:55:37 LOG5 begin_task: Level: (3) ID = <10058> Status = 0 0 0 0 ok 2009-Mar-14 21:55:37 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1385.68420410 MHz ...} 2009-Mar-14 21:55:37 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 8.997348 2009.2023644700485 18.999933 2009-Mar-14 21:55:37 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666830 21.900000000000002 2009-Mar-14 21:55:37 LOG4 log_alfabeam: ALFABEAM 1 8.968546279092076 21.797169256741125 2009-Mar-14 21:55:37 LOG4 log_alfabeam: ALFABEAM 2 8.973017885618779 21.871953801701100 2009-Mar-14 21:55:37 LOG4 log_alfabeam: ALFABEAM 3 8.971260605847966 21.975264206097716 2009-Mar-14 21:55:37 LOG4 log_alfabeam: ALFABEAM 4 8.964710752784343 22.002647736815135 2009-Mar-14 21:55:37 LOG4 log_alfabeam: ALFABEAM 5 8.960204818339582 21.925730432350125 2009-Mar-14 21:55:37 LOG4 log_alfabeam: ALFABEAM 6 8.962281966187348 21.823608481281120 2009-Mar-14 21:55:37 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300157 2009-Mar-14 21:55:38 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:55:38 LOG5 begin_task: Level: (4) ID = <10059> Status = 0 0 0 0 ok 2009-Mar-14 21:55:38 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:55:38 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635684204.0} 2009-Mar-14 21:55:38 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:55:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:55:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:55:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.571 (still bad) 2009-Mar-14 21:55:38 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1385.68420410 MHz ...} 2009-Mar-14 21:55:38 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6939.00 2009-Mar-14 21:55:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.684204 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:55:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:55:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:55:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:55:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:55:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.571 (still bad) 2009-Mar-14 21:55:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.569 (still bad) 2009-Mar-14 21:55:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.563 (still bad) 2009-Mar-14 21:55:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.565 (still bad) 2009-Mar-14 21:55:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.570 (still bad) 2009-Mar-14 21:55:49 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:55:49 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:55:49 LOG5 end_task: Level: (4) ID = <10059> Status = 0 0 0 0 ok 2009-Mar-14 21:55:49 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:55:49 LOG5 end_task: Level: (3) ID = <10058> Status = 0 0 0 0 ok 2009-Mar-14 21:55:49 INFO3 smartfreq: Taking CAL-ON at 1386.66076660 MHz ... 2009-Mar-14 21:55:49 LOG4 send_obs_status: To obs_status: <1> PART B7 MESSAGE {Taking CAL-ON at 1386.66076660 MHz ...} 2009-Mar-14 21:55:49 INFO4 set_smart_frequency: Setting frequency 1386.66076660 MHz 2009-Mar-14 21:55:49 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:55:49 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20236 J 2009-Mar-14 21:55:49 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:55:49 LOG2 antvel: Parameters to Doppler: Topocentric 93349 2009 73 0.0 2009-Mar-14 21:55:49 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:55:49 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1386.66076660 rest0=1386.66076660 rest1=1386.66076660 rest2=1386.66076660 rest3=1386.66076660 rest4=1386.66076660 rest5=1386.66076660 rest6=1386.66076660 rest7=1386.66076660 2009-Mar-14 21:55:49 INFO4 dopset_gen: New sky frequencies: 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 2009-Mar-14 21:55:49 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1386.660767 sky0=1386.660767 sky1=1386.660767 sky2=1386.660767 sky3=1386.660767 sky4=1386.660767 sky5=1386.660767 sky6=1386.660767 sky7=1386.660767 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:55:49 LOG2 dopset_gen: Result from 'sky2syn': 1636.660767 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:55:49 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1636660767.0} 2009-Mar-14 21:55:49 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:55:49 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1386.66076660 MHz}' 2009-Mar-14 21:55:49 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:55:49 LOG5 begin_task: Level: (3) ID = <10060> Status = 0 0 0 0 ok 2009-Mar-14 21:55:49 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1386.66076660 MHz ...} 2009-Mar-14 21:55:49 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.000691 2009.2023648503055 18.999933 2009-Mar-14 21:55:49 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666702 21.899999999999999 2009-Mar-14 21:55:49 LOG4 log_alfabeam: ALFABEAM 1 8.968645449491355 21.797530466551045 2009-Mar-14 21:55:49 LOG4 log_alfabeam: ALFABEAM 2 8.973044501542278 21.873146480936654 2009-Mar-14 21:55:49 LOG4 log_alfabeam: ALFABEAM 3 8.971187310423232 21.976117929788046 2009-Mar-14 21:55:49 LOG4 log_alfabeam: ALFABEAM 4 8.964611720758889 22.002272490526160 2009-Mar-14 21:55:49 LOG4 log_alfabeam: ALFABEAM 5 8.960180627989823 21.924520124928563 2009-Mar-14 21:55:49 LOG4 log_alfabeam: ALFABEAM 6 8.962356021053461 21.822795350710475 2009-Mar-14 21:55:49 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300158 2009-Mar-14 21:55:50 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:55:50 LOG5 begin_task: Level: (4) ID = <10061> Status = 0 0 0 0 ok 2009-Mar-14 21:55:50 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:55:50 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1636660767.0} 2009-Mar-14 21:55:50 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:55:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:55:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:55:50 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1386.66076660 MHz ...} 2009-Mar-14 21:55:50 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6951.00 2009-Mar-14 21:55:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.566 (still bad) 2009-Mar-14 21:55:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1636.660767 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:55:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:55:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:55:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:55:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:55:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:55:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.559 (still bad) 2009-Mar-14 21:55:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.562 (still bad) 2009-Mar-14 21:55:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.559 (still bad) 2009-Mar-14 21:55:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.560 (still bad) 2009-Mar-14 21:56:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.561 (still bad) 2009-Mar-14 21:56:01 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:56:01 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:56:01 LOG5 end_task: Level: (4) ID = <10061> Status = 0 0 0 0 ok 2009-Mar-14 21:56:01 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:56:01 LOG5 end_task: Level: (3) ID = <10060> Status = 0 0 0 0 ok 2009-Mar-14 21:56:01 INFO2 smartfreq: Starting smart frequency switching loop 2 of 2 2009-Mar-14 21:56:01 LOG4 send_obs_status: To obs_status: <1> LOOP 2 2009-Mar-14 21:56:01 LOG4 send_obs_status: To obs_status: <1> BITMAP stat_cal_off INFO {Making 7 CAL-OFFs followed by 7 CAL-ONs} MESSAGE {Setting CAL-OFF ...} 2009-Mar-14 21:56:01 LOG3 wapp_calcontrol: To CALCONTROL: CALOFF 2009-Mar-14 21:56:01 LOG3 sock_errsend: To CALCONTROL: CALOFF STATUS 2009-Mar-14 21:56:01 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 21:56:01 LOG5 begin_task: Level: (3) ID = <10062> Status = 0 0 0 0 ok 2009-Mar-14 21:56:01 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 21:56:01 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 21:56:01 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 21:56:01 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 21:56:01 LOG5 end_task: Level: (3) ID = <10062> Status = 0 0 0 0 ok 2009-Mar-14 21:56:01 LOG4 send_obs_status: To obs_status: <1> TOTALPARTS 2*7 2009-Mar-14 21:56:01 INFO3 smartfreq: Taking CAL-OFF at 1380.60607910 MHz ... 2009-Mar-14 21:56:01 LOG4 send_obs_status: To obs_status: <1> PART A1 MESSAGE {Taking CAL-OFF at 1380.60607910 MHz ...} 2009-Mar-14 21:56:01 INFO4 set_smart_frequency: Setting frequency 1380.60607910 MHz 2009-Mar-14 21:56:01 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:56:01 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:56:01 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:56:01 LOG2 antvel: Parameters to Doppler: Topocentric 93361 2009 73 0.0 2009-Mar-14 21:56:01 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:56:01 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1380.60607910 rest0=1380.60607910 rest1=1380.60607910 rest2=1380.60607910 rest3=1380.60607910 rest4=1380.60607910 rest5=1380.60607910 rest6=1380.60607910 rest7=1380.60607910 2009-Mar-14 21:56:01 INFO4 dopset_gen: New sky frequencies: 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 2009-Mar-14 21:56:01 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1380.606079 sky0=1380.606079 sky1=1380.606079 sky2=1380.606079 sky3=1380.606079 sky4=1380.606079 sky5=1380.606079 sky6=1380.606079 sky7=1380.606079 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:56:01 LOG2 dopset_gen: Result from 'sky2syn': 1630.606079 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:56:01 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1630606079.0} 2009-Mar-14 21:56:01 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:56:01 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1380.60607910 MHz}' 2009-Mar-14 21:56:01 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:56:01 LOG5 begin_task: Level: (3) ID = <10063> Status = 0 0 0 0 ok 2009-Mar-14 21:56:01 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1380.60607910 MHz ...} 2009-Mar-14 21:56:01 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.004033 2009.2023652305627 18.999933 2009-Mar-14 21:56:01 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666699 21.899999999999999 2009-Mar-14 21:56:01 LOG4 log_alfabeam: ALFABEAM 1 8.968743978419347 21.797909085434892 2009-Mar-14 21:56:01 LOG4 log_alfabeam: ALFABEAM 2 8.973069897972408 21.874340710678908 2009-Mar-14 21:56:01 LOG4 log_alfabeam: ALFABEAM 3 8.971113396133736 21.976955474614961 2009-Mar-14 21:56:01 LOG4 log_alfabeam: ALFABEAM 4 8.964513357497875 22.001879957036490 2009-Mar-14 21:56:01 LOG4 log_alfabeam: ALFABEAM 5 8.960157683490394 21.923309202101347 2009-Mar-14 21:56:01 LOG4 log_alfabeam: ALFABEAM 6 8.962430613239867 21.821998548983267 2009-Mar-14 21:56:01 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300159 2009-Mar-14 21:56:02 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:56:02 LOG5 begin_task: Level: (4) ID = <10064> Status = 0 0 0 0 ok 2009-Mar-14 21:56:02 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:56:02 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1630606079.0} 2009-Mar-14 21:56:02 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:56:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:56:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:56:02 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1380.60607910 MHz ...} 2009-Mar-14 21:56:02 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6963.00 2009-Mar-14 21:56:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.558 (still bad) 2009-Mar-14 21:56:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1630.606079 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:56:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:56:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:56:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:56:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:56:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.152 (still bad) 2009-Mar-14 21:56:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.150 (still bad) 2009-Mar-14 21:56:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.151 (still bad) 2009-Mar-14 21:56:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.156 (still bad) 2009-Mar-14 21:56:13 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:56:13 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:56:13 LOG5 end_task: Level: (4) ID = <10064> Status = 0 0 0 0 ok 2009-Mar-14 21:56:13 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:56:13 LOG5 end_task: Level: (3) ID = <10063> Status = 0 0 0 0 ok 2009-Mar-14 21:56:13 INFO3 smartfreq: Taking CAL-OFF at 1383.34045410 MHz ... 2009-Mar-14 21:56:13 LOG4 send_obs_status: To obs_status: <1> PART A2 MESSAGE {Taking CAL-OFF at 1383.34045410 MHz ...} 2009-Mar-14 21:56:13 INFO4 set_smart_frequency: Setting frequency 1383.34045410 MHz 2009-Mar-14 21:56:13 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:56:13 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:56:13 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:56:13 LOG2 antvel: Parameters to Doppler: Topocentric 93373 2009 73 0.0 2009-Mar-14 21:56:13 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:56:13 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1383.34045410 rest0=1383.34045410 rest1=1383.34045410 rest2=1383.34045410 rest3=1383.34045410 rest4=1383.34045410 rest5=1383.34045410 rest6=1383.34045410 rest7=1383.34045410 2009-Mar-14 21:56:13 INFO4 dopset_gen: New sky frequencies: 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 2009-Mar-14 21:56:13 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1383.340454 sky0=1383.340454 sky1=1383.340454 sky2=1383.340454 sky3=1383.340454 sky4=1383.340454 sky5=1383.340454 sky6=1383.340454 sky7=1383.340454 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:56:13 LOG2 dopset_gen: Result from 'sky2syn': 1633.340454 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:56:13 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1633340454.0} 2009-Mar-14 21:56:13 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:56:13 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1383.34045410 MHz}' 2009-Mar-14 21:56:13 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:56:13 LOG5 begin_task: Level: (3) ID = <10065> Status = 0 0 0 0 ok 2009-Mar-14 21:56:13 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1383.34045410 MHz ...} 2009-Mar-14 21:56:13 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.007376 2009.2023656108197 18.999933 2009-Mar-14 21:56:13 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666736 21.900000000000006 2009-Mar-14 21:56:13 LOG4 log_alfabeam: ALFABEAM 1 8.968841877069089 21.798304992634613 2009-Mar-14 21:56:13 LOG4 log_alfabeam: ALFABEAM 2 8.973094086055752 21.875536552995921 2009-Mar-14 21:56:13 LOG4 log_alfabeam: ALFABEAM 3 8.971038863636501 21.977777015785026 2009-Mar-14 21:56:13 LOG4 log_alfabeam: ALFABEAM 4 8.964415651499994 22.001470262573406 2009-Mar-14 21:56:13 LOG4 log_alfabeam: ALFABEAM 5 8.960135972322970 21.922097601640342 2009-Mar-14 21:56:13 LOG4 log_alfabeam: ALFABEAM 6 8.962505742467300 21.821217880564475 2009-Mar-14 21:56:13 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300160 2009-Mar-14 21:56:14 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:56:14 LOG5 begin_task: Level: (4) ID = <10066> Status = 0 0 0 0 ok 2009-Mar-14 21:56:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.150 (still bad) 2009-Mar-14 21:56:14 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:56:14 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1633340454.0} 2009-Mar-14 21:56:14 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:56:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:56:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:56:14 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1383.34045410 MHz ...} 2009-Mar-14 21:56:14 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6975.00 2009-Mar-14 21:56:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1633.340454 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:56:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:56:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:56:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:56:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:56:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.142 (still bad) 2009-Mar-14 21:56:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.144 (still bad) 2009-Mar-14 21:56:20 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 21:56:20 LOG4 check_wapp_levels: WAPP-1 power levels: 0.952 0.931 1.070 1.069 2009-Mar-14 21:56:20 LOG4 check_wapp_levels: WAPP-2 power levels: 1.028 0.973 1.130 1.129 2009-Mar-14 21:56:20 LOG4 check_wapp_levels: WAPP-3 power levels: 1.143 0.984 1.055 0.928 2009-Mar-14 21:56:20 LOG4 check_wapp_levels: WAPP-4 power levels: 0.947 0.109 1.045 0.118 2009-Mar-14 21:56:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.144 (still bad) 2009-Mar-14 21:56:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.145 (still bad) 2009-Mar-14 21:56:25 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:56:25 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:56:25 LOG5 end_task: Level: (4) ID = <10066> Status = 0 0 0 0 ok 2009-Mar-14 21:56:25 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:56:25 LOG5 end_task: Level: (3) ID = <10065> Status = 0 0 0 0 ok 2009-Mar-14 21:56:25 INFO3 smartfreq: Taking CAL-OFF at 1383.53576660 MHz ... 2009-Mar-14 21:56:25 LOG4 send_obs_status: To obs_status: <1> PART A3 MESSAGE {Taking CAL-OFF at 1383.53576660 MHz ...} 2009-Mar-14 21:56:25 INFO4 set_smart_frequency: Setting frequency 1383.53576660 MHz 2009-Mar-14 21:56:25 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:56:25 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:56:25 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:56:25 LOG2 antvel: Parameters to Doppler: Topocentric 93385 2009 73 0.0 2009-Mar-14 21:56:25 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:56:25 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1383.53576660 rest0=1383.53576660 rest1=1383.53576660 rest2=1383.53576660 rest3=1383.53576660 rest4=1383.53576660 rest5=1383.53576660 rest6=1383.53576660 rest7=1383.53576660 2009-Mar-14 21:56:25 INFO4 dopset_gen: New sky frequencies: 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 2009-Mar-14 21:56:25 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1383.535767 sky0=1383.535767 sky1=1383.535767 sky2=1383.535767 sky3=1383.535767 sky4=1383.535767 sky5=1383.535767 sky6=1383.535767 sky7=1383.535767 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:56:25 LOG2 dopset_gen: Result from 'sky2syn': 1633.535767 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:56:25 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1633535767.0} 2009-Mar-14 21:56:25 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:56:25 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1383.53576660 MHz}' 2009-Mar-14 21:56:25 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:56:25 LOG5 begin_task: Level: (3) ID = <10067> Status = 0 0 0 0 ok 2009-Mar-14 21:56:25 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1383.53576660 MHz ...} 2009-Mar-14 21:56:25 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.010718 2009.2023659910767 18.999933 2009-Mar-14 21:56:25 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666779 21.899999999999999 2009-Mar-14 21:56:25 LOG4 log_alfabeam: ALFABEAM 1 8.968939040579642 21.798717580478623 2009-Mar-14 21:56:25 LOG4 log_alfabeam: ALFABEAM 2 8.973117049199660 21.876732643890087 2009-Mar-14 21:56:25 LOG4 log_alfabeam: ALFABEAM 3 8.970963802932530 21.978581764260142 2009-Mar-14 21:56:25 LOG4 log_alfabeam: ALFABEAM 4 8.964318707050912 22.001044036403528 2009-Mar-14 21:56:25 LOG4 log_alfabeam: ALFABEAM 5 8.960115506743469 21.920886704690677 2009-Mar-14 21:56:25 LOG4 log_alfabeam: ALFABEAM 6 8.962581318521950 21.820454065635975 2009-Mar-14 21:56:25 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300161 2009-Mar-14 21:56:26 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:56:26 LOG5 begin_task: Level: (4) ID = <10068> Status = 0 0 0 0 ok 2009-Mar-14 21:56:26 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:56:26 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1633535767.0} 2009-Mar-14 21:56:26 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:56:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:56:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:56:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.143 (still bad) 2009-Mar-14 21:56:26 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1383.53576660 MHz ...} 2009-Mar-14 21:56:26 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6987.00 2009-Mar-14 21:56:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1633.535767 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:56:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:56:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:56:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:56:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:56:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.141 (still bad) 2009-Mar-14 21:56:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.141 (still bad) 2009-Mar-14 21:56:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.139 (still bad) 2009-Mar-14 21:56:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.140 (still bad) 2009-Mar-14 21:56:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.143 (still bad) 2009-Mar-14 21:56:37 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:56:37 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:56:37 LOG5 end_task: Level: (4) ID = <10068> Status = 0 0 0 0 ok 2009-Mar-14 21:56:37 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:56:37 LOG5 end_task: Level: (3) ID = <10067> Status = 0 0 0 0 ok 2009-Mar-14 21:56:37 INFO3 smartfreq: Taking CAL-OFF at 1384.12170410 MHz ... 2009-Mar-14 21:56:37 LOG4 send_obs_status: To obs_status: <1> PART A4 MESSAGE {Taking CAL-OFF at 1384.12170410 MHz ...} 2009-Mar-14 21:56:37 INFO4 set_smart_frequency: Setting frequency 1384.12170410 MHz 2009-Mar-14 21:56:37 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:56:37 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:56:37 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:56:37 LOG2 antvel: Parameters to Doppler: Topocentric 93397 2009 73 0.0 2009-Mar-14 21:56:37 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:56:37 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1384.12170410 rest0=1384.12170410 rest1=1384.12170410 rest2=1384.12170410 rest3=1384.12170410 rest4=1384.12170410 rest5=1384.12170410 rest6=1384.12170410 rest7=1384.12170410 2009-Mar-14 21:56:37 INFO4 dopset_gen: New sky frequencies: 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 2009-Mar-14 21:56:37 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1384.121704 sky0=1384.121704 sky1=1384.121704 sky2=1384.121704 sky3=1384.121704 sky4=1384.121704 sky5=1384.121704 sky6=1384.121704 sky7=1384.121704 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:56:37 LOG2 dopset_gen: Result from 'sky2syn': 1634.121704 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:56:37 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1634121704.0} 2009-Mar-14 21:56:37 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:56:37 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1384.12170410 MHz}' 2009-Mar-14 21:56:37 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:56:37 LOG5 begin_task: Level: (3) ID = <10069> Status = 0 0 0 0 ok 2009-Mar-14 21:56:37 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1384.12170410 MHz ...} 2009-Mar-14 21:56:37 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.014060 2009.2023663713337 18.999933 2009-Mar-14 21:56:37 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666702 21.899999999999999 2009-Mar-14 21:56:37 LOG4 log_alfabeam: ALFABEAM 1 8.969035453618448 21.799146571871002 2009-Mar-14 21:56:37 LOG4 log_alfabeam: ALFABEAM 2 8.973138794605092 21.877928697967548 2009-Mar-14 21:56:37 LOG4 log_alfabeam: ALFABEAM 3 8.970888237621166 21.979369699481779 2009-Mar-14 21:56:37 LOG4 log_alfabeam: ALFABEAM 4 8.964222539028134 22.000601564337803 2009-Mar-14 21:56:37 LOG4 log_alfabeam: ALFABEAM 5 8.960096277427496 21.919676797410190 2009-Mar-14 21:56:37 LOG4 log_alfabeam: ALFABEAM 6 8.962657318308620 21.819707093015673 2009-Mar-14 21:56:37 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300162 2009-Mar-14 21:56:38 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:56:38 LOG5 begin_task: Level: (4) ID = <10070> Status = 0 0 0 0 ok 2009-Mar-14 21:56:38 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:56:38 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1634121704.0} 2009-Mar-14 21:56:38 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:56:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:56:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:56:38 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1384.12170410 MHz ...} 2009-Mar-14 21:56:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.140 (still bad) 2009-Mar-14 21:56:38 INFO1 WAPP=1+2+3+4-start_spectra: start sec 6999.00 2009-Mar-14 21:56:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1634.121704 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:56:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:56:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:56:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:56:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:56:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.127 (still bad) 2009-Mar-14 21:56:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.128 (still bad) 2009-Mar-14 21:56:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.128 (still bad) 2009-Mar-14 21:56:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.127 (still bad) 2009-Mar-14 21:56:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.129 (still bad) 2009-Mar-14 21:56:49 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:56:49 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:56:49 LOG5 end_task: Level: (4) ID = <10070> Status = 0 0 0 0 ok 2009-Mar-14 21:56:49 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:56:49 LOG5 end_task: Level: (3) ID = <10069> Status = 0 0 0 0 ok 2009-Mar-14 21:56:49 INFO3 smartfreq: Taking CAL-OFF at 1385.29357910 MHz ... 2009-Mar-14 21:56:49 LOG4 send_obs_status: To obs_status: <1> PART A5 MESSAGE {Taking CAL-OFF at 1385.29357910 MHz ...} 2009-Mar-14 21:56:49 INFO4 set_smart_frequency: Setting frequency 1385.29357910 MHz 2009-Mar-14 21:56:49 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:56:49 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:56:49 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:56:49 LOG2 antvel: Parameters to Doppler: Topocentric 93409 2009 73 0.0 2009-Mar-14 21:56:49 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:56:49 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1385.29357910 rest0=1385.29357910 rest1=1385.29357910 rest2=1385.29357910 rest3=1385.29357910 rest4=1385.29357910 rest5=1385.29357910 rest6=1385.29357910 rest7=1385.29357910 2009-Mar-14 21:56:49 INFO4 dopset_gen: New sky frequencies: 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 2009-Mar-14 21:56:49 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1385.293579 sky0=1385.293579 sky1=1385.293579 sky2=1385.293579 sky3=1385.293579 sky4=1385.293579 sky5=1385.293579 sky6=1385.293579 sky7=1385.293579 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:56:49 LOG2 dopset_gen: Result from 'sky2syn': 1635.293579 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:56:49 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635293579.0} 2009-Mar-14 21:56:49 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:56:49 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1385.29357910 MHz}' 2009-Mar-14 21:56:49 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:56:49 LOG5 begin_task: Level: (3) ID = <10071> Status = 0 0 0 0 ok 2009-Mar-14 21:56:49 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1385.29357910 MHz ...} 2009-Mar-14 21:56:49 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.017403 2009.2023667515907 18.999933 2009-Mar-14 21:56:49 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666770 21.900000000000006 2009-Mar-14 21:56:49 LOG4 log_alfabeam: ALFABEAM 1 8.969131101609898 21.799591688513338 2009-Mar-14 21:56:49 LOG4 log_alfabeam: ALFABEAM 2 8.973159329889913 21.879124436862678 2009-Mar-14 21:56:49 LOG4 log_alfabeam: ALFABEAM 3 8.970812190977249 21.980140809730827 2009-Mar-14 21:56:49 LOG4 log_alfabeam: ALFABEAM 4 8.964127161536368 22.000143133057705 2009-Mar-14 21:56:49 LOG4 log_alfabeam: ALFABEAM 5 8.960078274659857 21.918468157985927 2009-Mar-14 21:56:49 LOG4 log_alfabeam: ALFABEAM 6 8.962733719125696 21.818976943303969 2009-Mar-14 21:56:49 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300163 2009-Mar-14 21:56:50 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:56:50 LOG5 begin_task: Level: (4) ID = <10072> Status = 0 0 0 0 ok 2009-Mar-14 21:56:50 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635293579.0} 2009-Mar-14 21:56:50 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:56:50 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:56:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:56:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:56:50 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1385.29357910 MHz ...} 2009-Mar-14 21:56:50 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7011.00 2009-Mar-14 21:56:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.127 (still bad) 2009-Mar-14 21:56:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.293579 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:56:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:56:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:56:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:56:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:56:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:56:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 21:56:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 21:56:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 21:56:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 21:57:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 21:57:01 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:57:01 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:57:01 LOG5 end_task: Level: (4) ID = <10072> Status = 0 0 0 0 ok 2009-Mar-14 21:57:01 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:57:01 LOG5 end_task: Level: (3) ID = <10071> Status = 0 0 0 0 ok 2009-Mar-14 21:57:01 INFO3 smartfreq: Taking CAL-OFF at 1385.68420410 MHz ... 2009-Mar-14 21:57:01 LOG4 send_obs_status: To obs_status: <1> PART A6 MESSAGE {Taking CAL-OFF at 1385.68420410 MHz ...} 2009-Mar-14 21:57:01 INFO4 set_smart_frequency: Setting frequency 1385.68420410 MHz 2009-Mar-14 21:57:01 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:57:01 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:57:01 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:57:01 LOG2 antvel: Parameters to Doppler: Topocentric 93421 2009 73 0.0 2009-Mar-14 21:57:01 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:57:01 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1385.68420410 rest0=1385.68420410 rest1=1385.68420410 rest2=1385.68420410 rest3=1385.68420410 rest4=1385.68420410 rest5=1385.68420410 rest6=1385.68420410 rest7=1385.68420410 2009-Mar-14 21:57:01 INFO4 dopset_gen: New sky frequencies: 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 2009-Mar-14 21:57:01 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1385.684204 sky0=1385.684204 sky1=1385.684204 sky2=1385.684204 sky3=1385.684204 sky4=1385.684204 sky5=1385.684204 sky6=1385.684204 sky7=1385.684204 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:57:01 LOG2 dopset_gen: Result from 'sky2syn': 1635.684204 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:57:01 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635684204.0} 2009-Mar-14 21:57:01 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:57:01 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1385.68420410 MHz}' 2009-Mar-14 21:57:01 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:57:01 LOG5 begin_task: Level: (3) ID = <10073> Status = 0 0 0 0 ok 2009-Mar-14 21:57:01 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1385.68420410 MHz ...} 2009-Mar-14 21:57:01 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.020745 2009.202367131848 18.999933 2009-Mar-14 21:57:01 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666729 21.899999999999999 2009-Mar-14 21:57:01 LOG4 log_alfabeam: ALFABEAM 1 8.969225885993831 21.800052230866875 2009-Mar-14 21:57:01 LOG4 log_alfabeam: ALFABEAM 2 8.973178646260530 21.880318517789071 2009-Mar-14 21:57:01 LOG4 log_alfabeam: ALFABEAM 3 8.970735754745432 21.980894422874087 2009-Mar-14 21:57:01 LOG4 log_alfabeam: ALFABEAM 4 8.964032672373495 21.999669461856492 2009-Mar-14 21:57:01 LOG4 log_alfabeam: ALFABEAM 5 8.960061502873712 21.917262138405306 2009-Mar-14 21:57:01 LOG4 log_alfabeam: ALFABEAM 6 8.962810429655336 21.818264221479534 2009-Mar-14 21:57:01 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300164 2009-Mar-14 21:57:02 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:57:02 LOG5 begin_task: Level: (4) ID = <10074> Status = 0 0 0 0 ok 2009-Mar-14 21:57:02 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:57:02 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635684204.0} 2009-Mar-14 21:57:02 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:57:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:57:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:57:02 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1385.68420410 MHz ...} 2009-Mar-14 21:57:02 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7023.00 2009-Mar-14 21:57:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 21:57:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.684204 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:57:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:57:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:57:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:57:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:57:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:05 INFO5 check_wapp_levels: WAPP power levels are between 0.108 and 1.110 (still bad) 2009-Mar-14 21:57:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 21:57:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 21:57:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 21:57:13 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:57:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.117 (still bad) 2009-Mar-14 21:57:13 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:57:13 LOG5 end_task: Level: (4) ID = <10074> Status = 0 0 0 0 ok 2009-Mar-14 21:57:13 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:57:13 LOG5 end_task: Level: (3) ID = <10073> Status = 0 0 0 0 ok 2009-Mar-14 21:57:13 INFO3 smartfreq: Taking CAL-OFF at 1386.66076660 MHz ... 2009-Mar-14 21:57:13 LOG4 send_obs_status: To obs_status: <1> PART A7 MESSAGE {Taking CAL-OFF at 1386.66076660 MHz ...} 2009-Mar-14 21:57:13 INFO4 set_smart_frequency: Setting frequency 1386.66076660 MHz 2009-Mar-14 21:57:13 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:57:13 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:57:13 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:57:13 LOG2 antvel: Parameters to Doppler: Topocentric 93433 2009 73 0.0 2009-Mar-14 21:57:13 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:57:13 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1386.66076660 rest0=1386.66076660 rest1=1386.66076660 rest2=1386.66076660 rest3=1386.66076660 rest4=1386.66076660 rest5=1386.66076660 rest6=1386.66076660 rest7=1386.66076660 2009-Mar-14 21:57:13 INFO4 dopset_gen: New sky frequencies: 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 2009-Mar-14 21:57:13 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1386.660767 sky0=1386.660767 sky1=1386.660767 sky2=1386.660767 sky3=1386.660767 sky4=1386.660767 sky5=1386.660767 sky6=1386.660767 sky7=1386.660767 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:57:13 LOG2 dopset_gen: Result from 'sky2syn': 1636.660767 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:57:13 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1636660767.0} 2009-Mar-14 21:57:13 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:57:13 LOG4 take_data: Calling 'take_data 10 1 SMARTF OFF stat_cal_off {CAL-OFF at 1386.66076660 MHz}' 2009-Mar-14 21:57:13 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:57:13 LOG5 begin_task: Level: (3) ID = <10075> Status = 0 0 0 0 ok 2009-Mar-14 21:57:13 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-OFF at 1386.66076660 MHz ...} 2009-Mar-14 21:57:13 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.024088 2009.202367512105 18.999933 2009-Mar-14 21:57:13 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666688 21.900000000000006 2009-Mar-14 21:57:13 LOG4 log_alfabeam: ALFABEAM 1 8.969319823952835 21.800528023320208 2009-Mar-14 21:57:13 LOG4 log_alfabeam: ALFABEAM 2 8.973196760560313 21.881511037790766 2009-Mar-14 21:57:13 LOG4 log_alfabeam: ALFABEAM 3 8.970658929475004 21.981630808077952 2009-Mar-14 21:57:13 LOG4 log_alfabeam: ALFABEAM 4 8.963939053892169 21.999180729699496 2009-Mar-14 21:57:13 LOG4 log_alfabeam: ALFABEAM 5 8.960045943925270 21.916058633945504 2009-Mar-14 21:57:13 LOG4 log_alfabeam: ALFABEAM 6 8.962887450306480 21.817568641040697 2009-Mar-14 21:57:13 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300165 2009-Mar-14 21:57:14 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:57:14 LOG5 begin_task: Level: (4) ID = <10076> Status = 0 0 0 0 ok 2009-Mar-14 21:57:14 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:57:14 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1636660767.0} 2009-Mar-14 21:57:14 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:57:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:57:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:57:14 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_off MESSAGE {Taking CAL-OFF at 1386.66076660 MHz ...} 2009-Mar-14 21:57:14 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7035.00 2009-Mar-14 21:57:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 21:57:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1636.660767 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:57:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:57:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:57:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:57:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:57:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 21:57:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 21:57:21 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 21:57:21 LOG4 check_wapp_levels: WAPP-1 power levels: 0.919 0.907 1.028 1.045 2009-Mar-14 21:57:21 LOG4 check_wapp_levels: WAPP-2 power levels: 1.013 0.951 1.076 1.112 2009-Mar-14 21:57:21 LOG4 check_wapp_levels: WAPP-3 power levels: 1.099 0.967 0.989 0.899 2009-Mar-14 21:57:21 LOG4 check_wapp_levels: WAPP-4 power levels: 0.931 0.109 1.026 0.118 2009-Mar-14 21:57:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 21:57:25 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:57:25 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:57:25 LOG5 end_task: Level: (4) ID = <10076> Status = 0 0 0 0 ok 2009-Mar-14 21:57:25 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:57:25 LOG5 end_task: Level: (3) ID = <10075> Status = 0 0 0 0 ok 2009-Mar-14 21:57:25 LOG4 send_obs_status: To obs_status: <1> BITMAP stat_cal_on INFO {Making 7 CAL-ONs} MESSAGE {Setting CAL-ON ...} 2009-Mar-14 21:57:25 LOG3 wapp_calcontrol: To CALCONTROL: CALON 2009-Mar-14 21:57:25 LOG3 sock_errsend: To CALCONTROL: CALON STATUS 2009-Mar-14 21:57:25 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 21:57:25 LOG5 begin_task: Level: (3) ID = <10077> Status = 0 0 0 0 ok 2009-Mar-14 21:57:25 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 21:57:25 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x03 2009-Mar-14 21:57:25 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 21:57:25 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 21:57:25 LOG5 end_task: Level: (3) ID = <10077> Status = 0 0 0 0 ok 2009-Mar-14 21:57:25 INFO3 smartfreq: Taking CAL-ON at 1380.60607910 MHz ... 2009-Mar-14 21:57:25 LOG4 send_obs_status: To obs_status: <1> PART B1 MESSAGE {Taking CAL-ON at 1380.60607910 MHz ...} 2009-Mar-14 21:57:25 INFO4 set_smart_frequency: Setting frequency 1380.60607910 MHz 2009-Mar-14 21:57:25 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:57:25 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:57:25 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:57:25 LOG2 antvel: Parameters to Doppler: Topocentric 93445 2009 73 0.0 2009-Mar-14 21:57:25 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:57:25 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1380.60607910 rest0=1380.60607910 rest1=1380.60607910 rest2=1380.60607910 rest3=1380.60607910 rest4=1380.60607910 rest5=1380.60607910 rest6=1380.60607910 rest7=1380.60607910 2009-Mar-14 21:57:25 INFO4 dopset_gen: New sky frequencies: 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 1380.606079 2009-Mar-14 21:57:25 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1380.606079 sky0=1380.606079 sky1=1380.606079 sky2=1380.606079 sky3=1380.606079 sky4=1380.606079 sky5=1380.606079 sky6=1380.606079 sky7=1380.606079 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:57:25 LOG2 dopset_gen: Result from 'sky2syn': 1630.606079 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:57:25 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1630606079.0} 2009-Mar-14 21:57:25 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:57:25 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1380.60607910 MHz}' 2009-Mar-14 21:57:25 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:57:25 LOG5 begin_task: Level: (3) ID = <10078> Status = 0 0 0 0 ok 2009-Mar-14 21:57:25 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1380.60607910 MHz ...} 2009-Mar-14 21:57:25 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.027430 2009.202367892362 18.999933 2009-Mar-14 21:57:25 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666690 21.899999999999991 2009-Mar-14 21:57:25 LOG4 log_alfabeam: ALFABEAM 1 8.969412821640331 21.801018313965915 2009-Mar-14 21:57:25 LOG4 log_alfabeam: ALFABEAM 2 8.973213668970947 21.882700677655794 2009-Mar-14 21:57:25 LOG4 log_alfabeam: ALFABEAM 3 8.970581807302652 21.982349371940771 2009-Mar-14 21:57:25 LOG4 log_alfabeam: ALFABEAM 4 8.963846399068869 21.998677706833146 2009-Mar-14 21:57:25 LOG4 log_alfabeam: ALFABEAM 5 8.960031597313808 21.914858967885881 2009-Mar-14 21:57:25 LOG4 log_alfabeam: ALFABEAM 6 8.962964689768127 21.816890730170901 2009-Mar-14 21:57:25 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300166 2009-Mar-14 21:57:26 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:57:26 LOG5 begin_task: Level: (4) ID = <10079> Status = 0 0 0 0 ok 2009-Mar-14 21:57:26 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:57:26 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1630606079.0} 2009-Mar-14 21:57:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 21:57:26 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:57:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:57:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:57:26 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1380.60607910 MHz ...} 2009-Mar-14 21:57:26 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7047.00 2009-Mar-14 21:57:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1630.606079 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:57:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:57:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:57:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:57:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:57:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1380.606079 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 21:57:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.627 (still bad) 2009-Mar-14 21:57:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.622 (still bad) 2009-Mar-14 21:57:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.626 (still bad) 2009-Mar-14 21:57:36 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.631 (still bad) 2009-Mar-14 21:57:37 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:57:37 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:57:37 LOG5 end_task: Level: (4) ID = <10079> Status = 0 0 0 0 ok 2009-Mar-14 21:57:37 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:57:37 LOG5 end_task: Level: (3) ID = <10078> Status = 0 0 0 0 ok 2009-Mar-14 21:57:37 INFO3 smartfreq: Taking CAL-ON at 1383.34045410 MHz ... 2009-Mar-14 21:57:37 LOG4 send_obs_status: To obs_status: <1> PART B2 MESSAGE {Taking CAL-ON at 1383.34045410 MHz ...} 2009-Mar-14 21:57:37 INFO4 set_smart_frequency: Setting frequency 1383.34045410 MHz 2009-Mar-14 21:57:37 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:57:37 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:57:37 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:57:37 LOG2 antvel: Parameters to Doppler: Topocentric 93457 2009 73 0.0 2009-Mar-14 21:57:37 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:57:37 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1383.34045410 rest0=1383.34045410 rest1=1383.34045410 rest2=1383.34045410 rest3=1383.34045410 rest4=1383.34045410 rest5=1383.34045410 rest6=1383.34045410 rest7=1383.34045410 2009-Mar-14 21:57:37 INFO4 dopset_gen: New sky frequencies: 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 1383.340454 2009-Mar-14 21:57:37 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1383.340454 sky0=1383.340454 sky1=1383.340454 sky2=1383.340454 sky3=1383.340454 sky4=1383.340454 sky5=1383.340454 sky6=1383.340454 sky7=1383.340454 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:57:37 LOG2 dopset_gen: Result from 'sky2syn': 1633.340454 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:57:37 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1633340454.0} 2009-Mar-14 21:57:37 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:57:37 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1383.34045410 MHz}' 2009-Mar-14 21:57:37 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:57:37 LOG5 begin_task: Level: (3) ID = <10080> Status = 0 0 0 0 ok 2009-Mar-14 21:57:37 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1383.34045410 MHz ...} 2009-Mar-14 21:57:37 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.030773 2009.202368272619 18.999933 2009-Mar-14 21:57:37 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666695 21.899999999999999 2009-Mar-14 21:57:37 LOG4 log_alfabeam: ALFABEAM 1 8.969504898982315 21.801522914161769 2009-Mar-14 21:57:37 LOG4 log_alfabeam: ALFABEAM 2 8.973229390312552 21.883887556176422 2009-Mar-14 21:57:37 LOG4 log_alfabeam: ALFABEAM 3 8.970504388048790 21.983050420236040 2009-Mar-14 21:57:37 LOG4 log_alfabeam: ALFABEAM 4 8.963754687468072 21.998160584252183 2009-Mar-14 21:57:37 LOG4 log_alfabeam: ALFABEAM 5 8.960018443001708 21.913663011014439 2009-Mar-14 21:57:37 LOG4 log_alfabeam: ALFABEAM 6 8.963042149374202 21.816230167703800 2009-Mar-14 21:57:37 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300167 2009-Mar-14 21:57:38 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:57:38 LOG5 begin_task: Level: (4) ID = <10081> Status = 0 0 0 0 ok 2009-Mar-14 21:57:38 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:57:38 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1633340454.0} 2009-Mar-14 21:57:38 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:57:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:57:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:57:38 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.625 (still bad) 2009-Mar-14 21:57:38 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1383.34045410 MHz ...} 2009-Mar-14 21:57:38 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7059.00 2009-Mar-14 21:57:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1633.340454 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:57:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:57:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:57:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:57:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:57:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1383.340454 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:40 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.625 (still bad) 2009-Mar-14 21:57:42 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.618 (still bad) 2009-Mar-14 21:57:44 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.615 (still bad) 2009-Mar-14 21:57:46 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.617 (still bad) 2009-Mar-14 21:57:48 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.617 (still bad) 2009-Mar-14 21:57:48 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 21:57:49 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:57:49 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:57:49 LOG5 end_task: Level: (4) ID = <10081> Status = 0 0 0 0 ok 2009-Mar-14 21:57:49 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:57:49 LOG5 end_task: Level: (3) ID = <10080> Status = 0 0 0 0 ok 2009-Mar-14 21:57:49 INFO3 smartfreq: Taking CAL-ON at 1383.53576660 MHz ... 2009-Mar-14 21:57:49 LOG4 send_obs_status: To obs_status: <1> PART B3 MESSAGE {Taking CAL-ON at 1383.53576660 MHz ...} 2009-Mar-14 21:57:49 INFO4 set_smart_frequency: Setting frequency 1383.53576660 MHz 2009-Mar-14 21:57:49 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:57:49 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:57:49 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:57:49 LOG2 antvel: Parameters to Doppler: Topocentric 93469 2009 73 0.0 2009-Mar-14 21:57:49 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:57:49 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1383.53576660 rest0=1383.53576660 rest1=1383.53576660 rest2=1383.53576660 rest3=1383.53576660 rest4=1383.53576660 rest5=1383.53576660 rest6=1383.53576660 rest7=1383.53576660 2009-Mar-14 21:57:49 INFO4 dopset_gen: New sky frequencies: 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 1383.535767 2009-Mar-14 21:57:49 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1383.535767 sky0=1383.535767 sky1=1383.535767 sky2=1383.535767 sky3=1383.535767 sky4=1383.535767 sky5=1383.535767 sky6=1383.535767 sky7=1383.535767 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:57:49 LOG2 dopset_gen: Result from 'sky2syn': 1633.535767 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:57:49 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1633535767.0} 2009-Mar-14 21:57:49 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:57:49 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1383.53576660 MHz}' 2009-Mar-14 21:57:49 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:57:49 LOG5 begin_task: Level: (3) ID = <10082> Status = 0 0 0 0 ok 2009-Mar-14 21:57:49 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1383.53576660 MHz ...} 2009-Mar-14 21:57:49 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.034115 2009.202368652876 18.999933 2009-Mar-14 21:57:49 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666681 21.899999999999999 2009-Mar-14 21:57:49 LOG4 log_alfabeam: ALFABEAM 1 8.969595967158613 21.802041027188757 2009-Mar-14 21:57:49 LOG4 log_alfabeam: ALFABEAM 2 8.973243925492785 21.885070384490483 2009-Mar-14 21:57:49 LOG4 log_alfabeam: ALFABEAM 3 8.970426763651046 21.983733437633063 2009-Mar-14 21:57:49 LOG4 log_alfabeam: ALFABEAM 4 8.963664006945995 21.997630175487480 2009-Mar-14 21:57:49 LOG4 log_alfabeam: ALFABEAM 5 8.960006475845208 21.912472051356449 2009-Mar-14 21:57:49 LOG4 log_alfabeam: ALFABEAM 6 8.963119738381515 21.815587406250277 2009-Mar-14 21:57:49 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300168 2009-Mar-14 21:57:50 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:57:50 LOG5 begin_task: Level: (4) ID = <10083> Status = 0 0 0 0 ok 2009-Mar-14 21:57:50 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:57:50 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1633535767.0} 2009-Mar-14 21:57:50 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:57:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:57:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:57:50 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1383.53576660 MHz ...} 2009-Mar-14 21:57:50 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7071.00 2009-Mar-14 21:57:51 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.615 (still bad) 2009-Mar-14 21:57:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1633.535767 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:57:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:57:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:57:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:57:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:57:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:52 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1383.535767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:57:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.609 (still bad) 2009-Mar-14 21:57:55 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.610 (still bad) 2009-Mar-14 21:57:55 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 21:57:57 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.610 (still bad) 2009-Mar-14 21:57:59 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.616 (still bad) 2009-Mar-14 21:58:01 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.615 (still bad) 2009-Mar-14 21:58:01 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:58:01 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:58:01 LOG5 end_task: Level: (4) ID = <10083> Status = 0 0 0 0 ok 2009-Mar-14 21:58:01 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:58:01 LOG5 end_task: Level: (3) ID = <10082> Status = 0 0 0 0 ok 2009-Mar-14 21:58:01 INFO3 smartfreq: Taking CAL-ON at 1384.12170410 MHz ... 2009-Mar-14 21:58:01 LOG4 send_obs_status: To obs_status: <1> PART B4 MESSAGE {Taking CAL-ON at 1384.12170410 MHz ...} 2009-Mar-14 21:58:01 INFO4 set_smart_frequency: Setting frequency 1384.12170410 MHz 2009-Mar-14 21:58:01 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:58:01 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:58:01 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:58:01 LOG2 antvel: Parameters to Doppler: Topocentric 93481 2009 73 0.0 2009-Mar-14 21:58:01 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:58:01 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1384.12170410 rest0=1384.12170410 rest1=1384.12170410 rest2=1384.12170410 rest3=1384.12170410 rest4=1384.12170410 rest5=1384.12170410 rest6=1384.12170410 rest7=1384.12170410 2009-Mar-14 21:58:01 INFO4 dopset_gen: New sky frequencies: 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 1384.121704 2009-Mar-14 21:58:01 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1384.121704 sky0=1384.121704 sky1=1384.121704 sky2=1384.121704 sky3=1384.121704 sky4=1384.121704 sky5=1384.121704 sky6=1384.121704 sky7=1384.121704 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:58:01 LOG2 dopset_gen: Result from 'sky2syn': 1634.121704 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:58:01 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1634121704.0} 2009-Mar-14 21:58:01 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:58:01 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1384.12170410 MHz}' 2009-Mar-14 21:58:01 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:58:01 LOG5 begin_task: Level: (3) ID = <10084> Status = 0 0 0 0 ok 2009-Mar-14 21:58:01 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1384.12170410 MHz ...} 2009-Mar-14 21:58:01 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.037458 2009.2023690331332 18.999933 2009-Mar-14 21:58:01 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666717 21.900000000000006 2009-Mar-14 21:58:01 LOG4 log_alfabeam: ALFABEAM 1 8.969686048938957 21.802572456739828 2009-Mar-14 21:58:01 LOG4 log_alfabeam: ALFABEAM 2 8.973257295074594 21.886249306699924 2009-Mar-14 21:58:01 LOG4 log_alfabeam: ALFABEAM 3 8.970348932846859 21.984398764736159 2009-Mar-14 21:58:01 LOG4 log_alfabeam: ALFABEAM 4 8.963574334191014 21.997086678149454 2009-Mar-14 21:58:01 LOG4 log_alfabeam: ALFABEAM 5 8.959995674173761 21.911285931894266 2009-Mar-14 21:58:01 LOG4 log_alfabeam: ALFABEAM 6 8.963197459376929 21.814962092088660 2009-Mar-14 21:58:01 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300169 2009-Mar-14 21:58:02 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:58:02 LOG5 begin_task: Level: (4) ID = <10085> Status = 0 0 0 0 ok 2009-Mar-14 21:58:02 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:58:02 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1634121704.0} 2009-Mar-14 21:58:02 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:58:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:58:02 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:58:02 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1384.12170410 MHz ...} 2009-Mar-14 21:58:02 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7083.00 2009-Mar-14 21:58:03 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.615 (still bad) 2009-Mar-14 21:58:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1634.121704 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:58:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:58:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:58:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:58:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:58:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:04 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1384.121704 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.594 (still bad) 2009-Mar-14 21:58:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.595 (still bad) 2009-Mar-14 21:58:08 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 14 (99999966 != 99999964 diff = 2)! 2009-Mar-14 21:58:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.595 (still bad) 2009-Mar-14 21:58:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.599 (still bad) 2009-Mar-14 21:58:13 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:58:13 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:58:13 LOG5 end_task: Level: (4) ID = <10085> Status = 0 0 0 0 ok 2009-Mar-14 21:58:13 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:58:13 LOG5 end_task: Level: (3) ID = <10084> Status = 0 0 0 0 ok 2009-Mar-14 21:58:13 INFO3 smartfreq: Taking CAL-ON at 1385.29357910 MHz ... 2009-Mar-14 21:58:13 LOG4 send_obs_status: To obs_status: <1> PART B5 MESSAGE {Taking CAL-ON at 1385.29357910 MHz ...} 2009-Mar-14 21:58:13 INFO4 set_smart_frequency: Setting frequency 1385.29357910 MHz 2009-Mar-14 21:58:13 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:58:13 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:58:13 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:58:13 LOG2 antvel: Parameters to Doppler: Topocentric 93493 2009 73 0.0 2009-Mar-14 21:58:13 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:58:13 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1385.29357910 rest0=1385.29357910 rest1=1385.29357910 rest2=1385.29357910 rest3=1385.29357910 rest4=1385.29357910 rest5=1385.29357910 rest6=1385.29357910 rest7=1385.29357910 2009-Mar-14 21:58:13 INFO4 dopset_gen: New sky frequencies: 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 1385.293579 2009-Mar-14 21:58:13 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1385.293579 sky0=1385.293579 sky1=1385.293579 sky2=1385.293579 sky3=1385.293579 sky4=1385.293579 sky5=1385.293579 sky6=1385.293579 sky7=1385.293579 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:58:13 LOG2 dopset_gen: Result from 'sky2syn': 1635.293579 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:58:13 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635293579.0} 2009-Mar-14 21:58:13 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:58:13 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1385.29357910 MHz}' 2009-Mar-14 21:58:13 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:58:13 LOG5 begin_task: Level: (3) ID = <10086> Status = 0 0 0 0 ok 2009-Mar-14 21:58:13 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1385.29357910 MHz ...} 2009-Mar-14 21:58:13 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.040800 2009.2023694133902 18.999933 2009-Mar-14 21:58:13 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666658 21.899999999999999 2009-Mar-14 21:58:13 LOG4 log_alfabeam: ALFABEAM 1 8.969775060757826 21.803116369018603 2009-Mar-14 21:58:13 LOG4 log_alfabeam: ALFABEAM 2 8.973269504392794 21.887423070289358 2009-Mar-14 21:58:13 LOG4 log_alfabeam: ALFABEAM 3 8.970270986819077 21.985045962610524 2009-Mar-14 21:58:13 LOG4 log_alfabeam: ALFABEAM 4 8.963485751725631 21.996530941240565 2009-Mar-14 21:58:13 LOG4 log_alfabeam: ALFABEAM 5 8.959986028536704 21.910105899702156 2009-Mar-14 21:58:13 LOG4 log_alfabeam: ALFABEAM 6 8.963275222706427 21.814354604414483 2009-Mar-14 21:58:13 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300170 2009-Mar-14 21:58:14 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:58:14 LOG5 begin_task: Level: (4) ID = <10087> Status = 0 0 0 0 ok 2009-Mar-14 21:58:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.594 (still bad) 2009-Mar-14 21:58:14 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:58:14 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635293579.0} 2009-Mar-14 21:58:14 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:58:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:58:14 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:58:14 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1385.29357910 MHz ...} 2009-Mar-14 21:58:14 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7095.00 2009-Mar-14 21:58:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.293579 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:58:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:58:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:58:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:58:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:58:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.594 (still bad) 2009-Mar-14 21:58:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.293579 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.567 (still bad) 2009-Mar-14 21:58:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.565 (still bad) 2009-Mar-14 21:58:22 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 21:58:22 LOG4 check_wapp_levels: WAPP-1 power levels: 1.292 1.256 1.427 1.450 2009-Mar-14 21:58:22 LOG4 check_wapp_levels: WAPP-2 power levels: 1.428 1.339 1.524 1.553 2009-Mar-14 21:58:22 LOG4 check_wapp_levels: WAPP-3 power levels: 1.566 1.374 1.414 1.220 2009-Mar-14 21:58:22 LOG4 check_wapp_levels: WAPP-4 power levels: 1.336 0.109 1.472 0.119 2009-Mar-14 21:58:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.568 (still bad) 2009-Mar-14 21:58:25 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:58:25 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:58:25 LOG5 end_task: Level: (4) ID = <10087> Status = 0 0 0 0 ok 2009-Mar-14 21:58:25 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:58:25 LOG5 end_task: Level: (3) ID = <10086> Status = 0 0 0 0 ok 2009-Mar-14 21:58:25 INFO3 smartfreq: Taking CAL-ON at 1385.68420410 MHz ... 2009-Mar-14 21:58:25 LOG4 send_obs_status: To obs_status: <1> PART B6 MESSAGE {Taking CAL-ON at 1385.68420410 MHz ...} 2009-Mar-14 21:58:25 INFO4 set_smart_frequency: Setting frequency 1385.68420410 MHz 2009-Mar-14 21:58:25 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:58:25 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:58:25 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:58:25 LOG2 antvel: Parameters to Doppler: Topocentric 93505 2009 73 0.0 2009-Mar-14 21:58:25 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:58:25 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1385.68420410 rest0=1385.68420410 rest1=1385.68420410 rest2=1385.68420410 rest3=1385.68420410 rest4=1385.68420410 rest5=1385.68420410 rest6=1385.68420410 rest7=1385.68420410 2009-Mar-14 21:58:25 INFO4 dopset_gen: New sky frequencies: 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 1385.684204 2009-Mar-14 21:58:25 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1385.684204 sky0=1385.684204 sky1=1385.684204 sky2=1385.684204 sky3=1385.684204 sky4=1385.684204 sky5=1385.684204 sky6=1385.684204 sky7=1385.684204 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:58:25 LOG2 dopset_gen: Result from 'sky2syn': 1635.684204 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:58:25 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635684204.0} 2009-Mar-14 21:58:25 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:58:25 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1385.68420410 MHz}' 2009-Mar-14 21:58:25 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:58:25 LOG5 begin_task: Level: (3) ID = <10088> Status = 0 0 0 0 ok 2009-Mar-14 21:58:25 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1385.68420410 MHz ...} 2009-Mar-14 21:58:25 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.044143 2009.2023697936472 18.999933 2009-Mar-14 21:58:25 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666690 21.899999999999999 2009-Mar-14 21:58:25 LOG4 log_alfabeam: ALFABEAM 1 8.969863028263422 21.803672565390038 2009-Mar-14 21:58:25 LOG4 log_alfabeam: ALFABEAM 2 8.973280575490330 21.888591847554725 2009-Mar-14 21:58:25 LOG4 log_alfabeam: ALFABEAM 3 8.970192922904033 21.985675404221663 2009-Mar-14 21:58:25 LOG4 log_alfabeam: ALFABEAM 4 8.963398233339120 21.995963163630496 2009-Mar-14 21:58:25 LOG4 log_alfabeam: ALFABEAM 5 8.959977515916247 21.908931767364898 2009-Mar-14 21:58:25 LOG4 log_alfabeam: ALFABEAM 6 8.963353032498823 21.813764559682554 2009-Mar-14 21:58:25 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300171 2009-Mar-14 21:58:26 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:58:26 LOG5 begin_task: Level: (4) ID = <10089> Status = 0 0 0 0 ok 2009-Mar-14 21:58:26 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:58:26 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635684204.0} 2009-Mar-14 21:58:26 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:58:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:58:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:58:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.568 (still bad) 2009-Mar-14 21:58:26 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1385.68420410 MHz ...} 2009-Mar-14 21:58:26 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7107.00 2009-Mar-14 21:58:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.684204 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:58:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:58:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:58:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:58:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:58:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:28 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.684204 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.568 (still bad) 2009-Mar-14 21:58:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.560 (still bad) 2009-Mar-14 21:58:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.560 (still bad) 2009-Mar-14 21:58:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.562 (still bad) 2009-Mar-14 21:58:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.561 (still bad) 2009-Mar-14 21:58:37 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:58:37 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:58:37 LOG5 end_task: Level: (4) ID = <10089> Status = 0 0 0 0 ok 2009-Mar-14 21:58:37 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:58:37 LOG5 end_task: Level: (3) ID = <10088> Status = 0 0 0 0 ok 2009-Mar-14 21:58:37 INFO3 smartfreq: Taking CAL-ON at 1386.66076660 MHz ... 2009-Mar-14 21:58:37 LOG4 send_obs_status: To obs_status: <1> PART B7 MESSAGE {Taking CAL-ON at 1386.66076660 MHz ...} 2009-Mar-14 21:58:37 INFO4 set_smart_frequency: Setting frequency 1386.66076660 MHz 2009-Mar-14 21:58:37 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:58:37 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:58:37 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:58:37 LOG2 antvel: Parameters to Doppler: Topocentric 93517 2009 73 0.0 2009-Mar-14 21:58:37 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:58:37 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1386.66076660 rest0=1386.66076660 rest1=1386.66076660 rest2=1386.66076660 rest3=1386.66076660 rest4=1386.66076660 rest5=1386.66076660 rest6=1386.66076660 rest7=1386.66076660 2009-Mar-14 21:58:37 INFO4 dopset_gen: New sky frequencies: 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 1386.660767 2009-Mar-14 21:58:37 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1386.660767 sky0=1386.660767 sky1=1386.660767 sky2=1386.660767 sky3=1386.660767 sky4=1386.660767 sky5=1386.660767 sky6=1386.660767 sky7=1386.660767 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:58:37 LOG2 dopset_gen: Result from 'sky2syn': 1636.660767 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:58:37 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1636660767.0} 2009-Mar-14 21:58:37 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:58:37 LOG4 take_data: Calling 'take_data 10 1 SMARTF ON stat_cal_on {CAL-ON at 1386.66076660 MHz}' 2009-Mar-14 21:58:37 START begin_task: Starting task 'WAPP+GALFA spectral observation' 2009-Mar-14 21:58:37 LOG5 begin_task: Level: (3) ID = <10090> Status = 0 0 0 0 ok 2009-Mar-14 21:58:37 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON at 1386.66076660 MHz ...} 2009-Mar-14 21:58:37 LOG5 log_alfabeam: Parameters: 8.9666666666666668 21.899999999999999 9.047485 2009.2023701739042 18.999933 2009-Mar-14 21:58:37 LOG4 log_alfabeam: ALFABEAM 0 8.966666666666688 21.899999999999999 2009-Mar-14 21:58:37 LOG4 log_alfabeam: ALFABEAM 1 8.969949873290451 21.804240182713986 2009-Mar-14 21:58:37 LOG4 log_alfabeam: ALFABEAM 2 8.973290517791048 21.889754427475651 2009-Mar-14 21:58:37 LOG4 log_alfabeam: ALFABEAM 3 8.970114831019336 21.986286724451894 2009-Mar-14 21:58:37 LOG4 log_alfabeam: ALFABEAM 4 8.963311856090710 21.995384222014696 2009-Mar-14 21:58:37 LOG4 log_alfabeam: ALFABEAM 5 8.959970122926293 21.907764736215430 2009-Mar-14 21:58:37 LOG4 log_alfabeam: ALFABEAM 6 8.963430800662975 21.813192266648198 2009-Mar-14 21:58:37 INFO2 take_data: Starting WAPP+GALFA 10-second scan: 907300172 2009-Mar-14 21:58:38 START begin_task: Starting task 'waiting on WAPP+GALFA spectra' 2009-Mar-14 21:58:38 LOG5 begin_task: Level: (4) ID = <10091> Status = 0 0 0 0 ok 2009-Mar-14 21:58:38 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 21:58:38 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1636660767.0} 2009-Mar-14 21:58:38 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:58:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:58:38 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:58:38 LOG4 send_obs_status: To obs_status: <0> TASKTIME 10 BITMAP stat_cal_on MESSAGE {Taking CAL-ON at 1386.66076660 MHz ...} 2009-Mar-14 21:58:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.562 (still bad) 2009-Mar-14 21:58:38 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7119.00 2009-Mar-14 21:58:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1636.660767 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 21:58:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:58:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 21:58:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 21:58:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 21:58:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:40 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1386.660767 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 21:58:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.555 (still bad) 2009-Mar-14 21:58:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.557 (still bad) 2009-Mar-14 21:58:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.555 (still bad) 2009-Mar-14 21:58:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.553 (still bad) 2009-Mar-14 21:58:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.557 (still bad) 2009-Mar-14 21:58:49 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 21:58:49 STOP end_task: Finishing task 'waiting on WAPP+GALFA spectra' with status 'OK' 2009-Mar-14 21:58:49 LOG5 end_task: Level: (4) ID = <10091> Status = 0 0 0 0 ok 2009-Mar-14 21:58:49 STOP end_task: Finishing task 'WAPP+GALFA spectral observation' with status 'OK' 2009-Mar-14 21:58:49 LOG5 end_task: Level: (3) ID = <10090> Status = 0 0 0 0 ok 2009-Mar-14 21:58:49 INFO2 smartfreq: Switching off CAL 2009-Mar-14 21:58:49 LOG3 wapp_calcontrol: To CALCONTROL: CALOFF 2009-Mar-14 21:58:49 LOG3 sock_errsend: To CALCONTROL: CALOFF STATUS 2009-Mar-14 21:58:49 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 21:58:49 LOG5 begin_task: Level: (3) ID = <10092> Status = 0 0 0 0 ok 2009-Mar-14 21:58:49 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 21:58:49 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 21:58:49 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 21:58:49 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 21:58:49 LOG5 end_task: Level: (3) ID = <10092> Status = 0 0 0 0 ok 2009-Mar-14 21:58:49 INFO3 restore_frequencies: Restoring original frequencies 2009-Mar-14 21:58:49 LOG5 antvel: Calling 'antvel 85800.000000 215400.000000 J Topocentric 0' 2009-Mar-14 21:58:49 LOG2 antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 21:58:49 LOG2 antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 21:58:49 LOG2 antvel: Parameters to Doppler: Topocentric 93529 2009 73 0.0 2009-Mar-14 21:58:49 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 21:58:49 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1385.0 rest0=1385.0 rest1=1385.0 rest2=1385.0 rest3=1385.0 rest4=1385.0 rest5=1385.0 rest6=1385.0 rest7=1385.0 2009-Mar-14 21:58:49 INFO4 dopset_gen: New sky frequencies: 1385.000000 1385.000000 1385.000000 1385.000000 1385.000000 1385.000000 1385.000000 1385.000000 1385.000000 2009-Mar-14 21:58:49 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1385.000000 sky0=1385.000000 sky1=1385.000000 sky2=1385.000000 sky3=1385.000000 sky4=1385.000000 sky5=1385.000000 sky6=1385.000000 sky7=1385.000000 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 21:58:49 LOG2 dopset_gen: Result from 'sky2syn': 1635.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 21:58:49 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635000000.0} 2009-Mar-14 21:58:49 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:58:49 STOP finish_task: Finishing task 'smart frequency switching' 2009-Mar-14 21:58:49 LOG5 finish_task: Level: (2) ID = <10023> Status = 0 0 0 0 ok 2009-Mar-14 21:58:49 DONE finish_task: DONE finished pattern: smart frequency switching 2009-Mar-14 21:58:49 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 21:58:49 END end_task: Finishing task 'smart frequency switching' with status 'OK' 2009-Mar-14 21:58:49 LOG5 end_task: Level: (2) ID = <10023> Status = 0 0 0 0 ok 2009-Mar-14 21:58:49 NOTE run_command_file: DONE with command file processing 2009-Mar-14 21:58:50 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Running Command File} 2009-Mar-14 21:58:50 STOP finish_task: Finishing task 'running command file 'command_galfasrc09.cmd'' 2009-Mar-14 21:58:50 LOG5 finish_task: Level: (1) ID = <10005> Status = 0 0 0 0 ok 2009-Mar-14 21:58:50 DONE finish_task: DONE finished running: command file 'command_galfasrc09.cmd' 2009-Mar-14 21:58:50 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 21:58:50 END end_task: Finishing task 'running command file 'command_galfasrc09.cmd'' with status 'OK' 2009-Mar-14 21:58:50 LOG5 end_task: Level: (1) ID = <10005> Status = 0 0 0 0 ok 2009-Mar-14 21:58:50 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635000000.0} 2009-Mar-14 21:58:50 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 21:58:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:58:50 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 21:58:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.553 (still bad) 2009-Mar-14 21:59:44 COMMAND CIMA-send_to_exec: Sending command to restart the WAPPs 2009-Mar-14 21:59:44 LOG4 exec_msg: From OBSERVER: restart_wapp 2009-Mar-14 21:59:44 LOG5 restart_wapp: Calling 'restart_wapp' 2009-Mar-14 21:59:44 BEGIN begin_task: Starting task 'restarting the WAPPs' 2009-Mar-14 21:59:44 LOG5 begin_task: Level: (1) ID = <10093> Status = 0 0 0 0 ok 2009-Mar-14 21:59:44 NOTE restart_wapp: Restarting all WAPPs 2009-Mar-14 21:59:44 WARNING restart_wapp: WARNING don't forget to reconfigure the WAPPs after the restart! 2009-Mar-14 21:59:44 END end_task: Finishing task 'restarting the WAPPs' with status 'OK' 2009-Mar-14 21:59:44 LOG5 end_task: Level: (1) ID = <10093> Status = 0 0 0 0 ok 2009-Mar-14 21:59:44 INFO1 WAPPDATA-flush_pending: WAPPDATA ready 2009-Mar-14 21:59:44 LOG3 exec_msg: Closing socket 2009-Mar-14 21:59:44 LOG3 exec_msg: Closing socket 2009-Mar-14 21:59:44 LOG3 exec_msg: Closing socket 2009-Mar-14 21:59:44 LOG3 exec_msg: Closing socket 2009-Mar-14 21:59:47 ALERT WAPP=2-wappcon: WAPP2 restarting 2009-Mar-14 21:59:47 ALERT WAPP=3-wappcon: WAPP3 restarting 2009-Mar-14 21:59:47 ALERT WAPP=1-wappcon: WAPP1 restarting 2009-Mar-14 21:59:47 ALERT WAPP=4-wappcon: WAPP4 restarting 2009-Mar-14 22:00:23 NOTE CIMA-load_config_file: Loading and applying configuration file 'a2010_az180_2009.conf' 2009-Mar-14 22:00:24 LOG2 CIMA-antvel: Precessing RA = 08:58:00.0 Dec = +21:54:00.0 Epoch = 2009.20237 J 2009-Mar-14 22:00:24 LOG2 CIMA-antvel: Computed apparent RA = 08:58:33.9 Dec = +21:51:48.0 2009-Mar-14 22:00:24 LOG2 CIMA-antvel: Parameters to Doppler: Topocentric 93623 2009 73 0.0 2009-Mar-14 22:00:24 INFO5 CIMA-antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(fast_config) "yes" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(config_type) "standard" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(receiver) "alfa" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(quick_tsys) "no" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(ifsetup_only) "no" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(retrack_source) "yes" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(path) "ALFA" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(restcent) "1385.0" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest1) "1385.0" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest2) "1385.0" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest3) "1385.0" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest4) "1385.0" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest5) "1385.0" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest6) "1385.0" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest7) "1385.0" 2009-Mar-14 22:00:24 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rest8) "1385.0" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(dest1) "250" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(dest2) "250" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(dest3) "250" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(dest4) "250" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq1) "0.000000" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq2) "0.000000" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq3) "0.000000" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq4) "0.000000" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq5) "0.000000" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq6) "0.000000" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq7) "0.000000" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(synfrq8) "0.000000" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(calctype) "SUBBAND" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(backends) "WAPP" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(radarblanker) "off" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(polsel) "skip" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(filtersel) "alfafb 1" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(sbshcl) "T" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(shcl) "skip" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rfnum) "skip" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(zmnormal) "T" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(rfattn) "11 11" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(ifnum) "6" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(up) "1635.000000" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(ifattn) "0 0" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(fiber) "T" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(ac2sw) "skip" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(phbsig) "skip" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(hybrid) "skip" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(phblo) "skip" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(xfnormal) "T" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(sigsrc) "gr" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(gain) "8 8" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(inpfrq) "alfa" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(mixer) "750 750 750 750 750 750 750 750" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(vlbainp) "skip" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(syndest) "3 3 3 3 3 3 3 3" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(calsrc) "3" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(750nb) "skip" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(2to12wb) "F" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(calrcvr) "15" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(2a2b30if) "skip" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(vis30mhz) "gr" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global iflo ; set iflo(430blnk) "F" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw1) "100" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw2) "100" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw3) "100" 2009-Mar-14 22:00:25 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw4) "100" 2009-Mar-14 22:00:26 COMMAND CIMA-send_to_exec: Sending command to apply receiver IF/LO set-up 2009-Mar-14 22:00:26 LOG4 exec_msg: From OBSERVER: config_iflo 2009-Mar-14 22:00:26 BEGIN begin_task: Starting task 'configuring IF/LO path' 2009-Mar-14 22:00:26 LOG5 begin_task: Level: (1) ID = <10094> Status = 0 0 0 0 ok 2009-Mar-14 22:00:26 INFO1 config_iflo: Starting to configure IF/LO path for ALFA 2009-Mar-14 22:00:26 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Configuring IF/LO path} TASKWAIT BITMAP stat_iflo INFO {Setting up the IF/LO path ...} 2009-Mar-14 22:00:26 LOG1 config_iflo: Receiver ALFA already selected 2009-Mar-14 22:00:26 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:00:26 LOG3 socket_wait: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:00:26 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:00:26 LOG5 begin_task: Level: (2) ID = <10095> Status = 0 0 0 0 ok 2009-Mar-14 22:00:26 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:00:26 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:00:26 LOG5 end_task: Level: (2) ID = <10095> Status = 0 0 0 0 ok 2009-Mar-14 22:00:26 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:00:26 LOG3 to_alfamon: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:00:26 LOG3 config_iflo: Skipping filter command 'alfafb 1' since system already is properly set 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if1-command 'if1_sbshcl T' since system already is properly set 2009-Mar-14 22:00:26 LOG5 send_ifx: Skipping if1-command 'if1_shcl skip' since not applicable 2009-Mar-14 22:00:26 LOG5 send_ifx: Skipping if1-command 'if1_rfnum skip' since not applicable 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if1-command 'if1_zmnormal T' since system already is properly set 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if1-command 'if1_rfattn 11 11' since system already is properly set 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if1-command 'if1_ifnum 6' since system already is properly set 2009-Mar-14 22:00:26 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635000000.0} 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if1-command 'if1_ifattn 0 0' since system already is properly set 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if1-command 'if1_fiber T' since system already is properly set 2009-Mar-14 22:00:26 LOG5 send_ifx: Skipping if1-command 'if1_ac2sw skip' since not applicable 2009-Mar-14 22:00:26 LOG5 send_ifx: Skipping if1-command 'if1_phbsig skip' since not applicable 2009-Mar-14 22:00:26 LOG5 send_ifx: Skipping if1-command 'if1_hybrid skip' since not applicable 2009-Mar-14 22:00:26 LOG5 send_ifx: Skipping if1-command 'if1_phblo skip' since not applicable 2009-Mar-14 22:00:26 LOG5 send_ifx: Skipping if1-command 'if1_750nb skip' since not applicable 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if1-command 'if1_2to12wb F' since system already is properly set 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if1-command 'if1_calrcvr 15' since system already is properly set 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if2-command 'if2_xfnormal T' since system already is properly set 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if2-command 'if2_sigsrc gr' since system already is properly set 2009-Mar-14 22:00:26 LOG3 vw_send: To DATATAKING: if2 {if2_gain 8 8} 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if2-command 'if2_inpfrq alfa' since system already is properly set 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if2-command 'if2_mixer 750 750 750 750 750 750 750 750' since system already is properly set 2009-Mar-14 22:00:26 LOG5 send_ifx: Skipping if2-command 'if2_vlbainp skip' since not applicable 2009-Mar-14 22:00:26 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if2-command 'if2_syndest 3 3 3 3 3 3 3 3' since system already is properly set 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if2-command 'if2_calsrc 3' since system already is properly set 2009-Mar-14 22:00:26 LOG5 send_ifx: Skipping if2-command 'if2_2a2b30if skip' since not applicable 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if2-command 'if2_vis30mhz gr' since system already is properly set 2009-Mar-14 22:00:26 LOG3 send_ifx: Skipping if2-command 'if2_430blnk F' since system already is properly set 2009-Mar-14 22:00:26 LOG2 socket_wait: Starting sockwait on DATATAKING for 'configuring IF/LO path' using string 'DONE' 2009-Mar-14 22:00:26 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:00:26 START begin_task: Starting task 'waiting on configuring IF/LO path' 2009-Mar-14 22:00:26 LOG5 begin_task: Level: (2) ID = <10096> Status = 0 0 0 0 ok 2009-Mar-14 22:00:26 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635000000.0} 2009-Mar-14 22:00:26 LOG4 got_cormsg: From DATATAKING: if2 {if2_gain 8 8} 2009-Mar-14 22:00:26 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 22:00:26 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:00:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:00:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:00:26 LOG4 got_cormsg: From DATATAKING: vw% DONE 2009-Mar-14 22:00:26 STOP end_task: Finishing task 'waiting on configuring IF/LO path' with status 'OK' 2009-Mar-14 22:00:26 LOG5 end_task: Level: (2) ID = <10096> Status = 0 0 0 0 ok 2009-Mar-14 22:00:26 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'configuring IF/LO path' 2009-Mar-14 22:00:26 STOP finish_task: Finishing task 'configuring IF/LO path' 2009-Mar-14 22:00:26 LOG5 finish_task: Level: (1) ID = <10094> Status = 0 0 0 0 ok 2009-Mar-14 22:00:26 DONE finish_task: DONE finished configuration: IF/LO path 2009-Mar-14 22:00:26 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 22:00:26 END end_task: Finishing task 'configuring IF/LO path' with status 'OK' 2009-Mar-14 22:00:26 LOG5 end_task: Level: (1) ID = <10094> Status = 0 0 0 0 ok 2009-Mar-14 22:00:26 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_enabled1) "1" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_enabled2) "1" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_enabled3) "1" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_enabled4) "1" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_cfg1) "2 chan, 3-level" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_cfg2) "2 chan, 3-level" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_cfg3) "2 chan, 3-level" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_cfg4) "2 chan, 3-level" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw1) "100" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw2) "100" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw3) "100" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_bw4) "100" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(wapp_dumptime) "1" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(alfa) "1" 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: global wapp ; set wapp(dual) "1" 2009-Mar-14 22:00:27 COMMAND CIMA-send_to_exec: Sending command to configure the WAPPs 2009-Mar-14 22:00:27 LOG4 exec_msg: From OBSERVER: config_wapp_correlator 2009-Mar-14 22:00:27 BEGIN begin_task: Starting task 'configuring WAPPs' 2009-Mar-14 22:00:27 LOG5 begin_task: Level: (1) ID = <10097> Status = 0 0 0 0 ok 2009-Mar-14 22:00:27 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Configuring WAPPs} TASKWAIT BITMAP stat_corr INFO {Configuring the WAPPs ...} 2009-Mar-14 22:00:27 INFO1 config_wapp_correlator: Starting to configure WAPP as correlator 2009-Mar-14 22:00:27 LOG2 set_cal_source: Setting cal signal control to the WAPPs 2009-Mar-14 22:00:27 START begin_task: Starting task 'selecting calibration port' 2009-Mar-14 22:00:27 LOG5 begin_task: Level: (2) ID = <10098> Status = 0 0 0 0 ok 2009-Mar-14 22:00:27 LOG3 vw_send: To DATATAKING: calport 3 2009-Mar-14 22:00:27 LOG2 socket_wait: Starting sockwait on DATATAKING for 'calport' using string 'DONE' 2009-Mar-14 22:00:27 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:00:27 START begin_task: Starting task 'waiting on calport' 2009-Mar-14 22:00:27 LOG5 begin_task: Level: (3) ID = <10099> Status = 0 0 0 0 ok 2009-Mar-14 22:00:27 LOG5 CIMA-load_config_file: ALFA is already centered on beam 0. 2009-Mar-14 22:00:27 LOG4 got_cormsg: From DATATAKING: calport 3 2009-Mar-14 22:00:27 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:00:27 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:00:27 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 22:00:27 STOP end_task: Finishing task 'waiting on calport' with status 'OK' 2009-Mar-14 22:00:27 LOG5 end_task: Level: (3) ID = <10099> Status = 0 0 0 0 ok 2009-Mar-14 22:00:27 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'calport' 2009-Mar-14 22:00:27 STOP end_task: Finishing task 'selecting calibration port' with status 'OK' 2009-Mar-14 22:00:27 LOG5 end_task: Level: (2) ID = <10098> Status = 0 0 0 0 ok 2009-Mar-14 22:00:27 LOG3 wapp_calcontrol: To CALCONTROL: CALOFF 2009-Mar-14 22:00:27 LOG3 sock_errsend: To CALCONTROL: CALOFF STATUS 2009-Mar-14 22:00:27 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 22:00:27 LOG5 begin_task: Level: (2) ID = <10100> Status = 0 0 0 0 ok 2009-Mar-14 22:00:27 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:00:27 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 22:00:27 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 22:00:27 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 22:00:27 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 22:00:27 LOG5 end_task: Level: (2) ID = <10100> Status = 0 0 0 0 ok 2009-Mar-14 22:00:27 LOG3 send_to_one_wapp: To WAPPCON: VERBOSE 0 2009-Mar-14 22:00:27 LOG3 send_to_one_wapp: To WAPPCON2: VERBOSE 0 2009-Mar-14 22:00:27 LOG3 send_to_one_wapp: To WAPPCON3: VERBOSE 0 2009-Mar-14 22:00:27 LOG3 send_to_one_wapp: To WAPPCON4: VERBOSE 0 2009-Mar-14 22:00:28 LOG3 send_to_one_wapp: To WAPPCON: TIMEOUT 5 2009-Mar-14 22:00:28 LOG3 send_to_one_wapp: To WAPPCON2: TIMEOUT 5 2009-Mar-14 22:00:28 LOG3 send_to_one_wapp: To WAPPCON3: TIMEOUT 5 2009-Mar-14 22:00:28 LOG3 send_to_one_wapp: To WAPPCON4: TIMEOUT 5 2009-Mar-14 22:00:28 LOG3 send_to_one_wapp: To WAPPCON: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:00:28 LOG3 send_to_one_wapp: To WAPPCON2: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:00:28 LOG3 send_to_one_wapp: To WAPPCON3: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:00:28 LOG3 send_to_one_wapp: To WAPPCON4: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:00:28 LOG3 wapp_calcontrol: To CALCONTROL: TRIGCLOCK 2009-Mar-14 22:00:28 LOG3 sock_errsend: To CALCONTROL: TRIGCLOCK STATUS 2009-Mar-14 22:00:28 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 22:00:28 LOG5 begin_task: Level: (2) ID = <10101> Status = 0 0 0 0 ok 2009-Mar-14 22:00:28 LOG4 WAPP=1+2+3+4-wappcon: Received command 'VERBOSE 0' 2009-Mar-14 22:00:28 LOG4 WAPP=1+2+3+4-wappcon: Received command 'TIMEOUT 5' 2009-Mar-14 22:00:28 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 22:00:28 LOG4 WAPP=1+2+3+4-wappcon: Received command 'PROJECT a2010 Lyle Hoffman' 2009-Mar-14 22:00:28 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 22:00:28 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 22:00:28 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 22:00:28 LOG5 end_task: Level: (2) ID = <10101> Status = 0 0 0 0 ok 2009-Mar-14 22:00:28 LOG3 sock_errsend: To WAPPDATA: FLUSH 2009-Mar-14 22:00:28 STOP finish_task: Finishing task 'configuring WAPPs' 2009-Mar-14 22:00:28 LOG5 finish_task: Level: (1) ID = <10097> Status = 0 0 0 0 ok 2009-Mar-14 22:00:28 DONE finish_task: DONE finished configuring: the WAPPs in ALFA mode 2009-Mar-14 22:00:28 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 22:00:28 END end_task: Finishing task 'configuring WAPPs' with status 'OK' 2009-Mar-14 22:00:28 LOG5 end_task: Level: (1) ID = <10097> Status = 0 0 0 0 ok 2009-Mar-14 22:00:28 INFO1 WAPPDATA-flush_pending: WAPPDATA ready 2009-Mar-14 22:00:28 COMMAND CIMA-send_to_exec: Sending command to rotate ALFA 2009-Mar-14 22:00:28 LOG4 exec_msg: From OBSERVER: rotate_alfa 19 nowait 2009-Mar-14 22:00:28 BEGIN begin_task: Starting task 'rotate ALFA to +19 degrees' 2009-Mar-14 22:00:28 LOG5 begin_task: Level: (1) ID = <10102> Status = 0 0 0 0 ok 2009-Mar-14 22:00:28 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Rotating ALFA} INFO {Rotating ALFA to +19 degrees ...} 2009-Mar-14 22:00:28 INFO2 rotate_alfa: ALFA commanded to +19.0 degrees 2009-Mar-14 22:00:28 LOG3 sock_errsend: To ALFAMOTOR: POSITION 19 REPLY 2009-Mar-14 22:00:28 STOP finish_task: Finishing task 'rotate ALFA to +19 degrees' 2009-Mar-14 22:00:28 LOG5 finish_task: Level: (1) ID = <10102> Status = 0 0 0 0 ok 2009-Mar-14 22:00:28 DONE finish_task: DONE finished configuration: rotating ALFA to +19 degrees 2009-Mar-14 22:00:28 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 22:00:28 END end_task: Finishing task 'rotate ALFA to +19 degrees' with status 'OK' 2009-Mar-14 22:00:28 LOG5 end_task: Level: (1) ID = <10102> Status = 0 0 0 0 ok 2009-Mar-14 22:00:29 LOG4 exec_msg: From ALFAMOTOR: alfa_motor "INPOSITION" 2009-Mar-14 22:00:29 INFO3 alfa_motor: ALFA rotator in-position +19.00 degrees 2009-Mar-14 22:00:29 NOTE CIMA-load_config_file: Configuration file 'a2010_az180_2009.conf' applied. 2009-Mar-14 22:01:22 COMMAND CIMA-send_to_exec: Sending command to adjust IF1+IF2+WAPP power 2009-Mar-14 22:01:22 LOG4 exec_msg: From OBSERVER: adjust_power WAPP all 2009-Mar-14 22:01:22 BEGIN begin_task: Starting task 'adjusting WAPP power' 2009-Mar-14 22:01:22 LOG5 begin_task: Level: (1) ID = <10103> Status = 0 0 0 0 ok 2009-Mar-14 22:01:22 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Adjusting WAPP power} TASKWAIT BITMAP stat_power INFO {Adjusting WAPP power ...} 2009-Mar-14 22:01:22 INFO2 adjust_power: Starting to adjust WAPP power 2009-Mar-14 22:01:22 LOG3 vw_send: To DATATAKING: adjpwrif2 2009-Mar-14 22:01:22 LOG2 socket_wait: Starting sockwait on DATATAKING for 'adjpwrif2' using string 'DONE' 2009-Mar-14 22:01:22 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:01:22 START begin_task: Starting task 'waiting on adjpwrif2' 2009-Mar-14 22:01:22 LOG5 begin_task: Level: (2) ID = <10104> Status = 0 0 0 0 ok 2009-Mar-14 22:01:22 LOG4 got_cormsg: From DATATAKING: adjpwrif2 2009-Mar-14 22:01:22 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:01:25 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:01:25 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 22:01:25 STOP end_task: Finishing task 'waiting on adjpwrif2' with status 'OK' 2009-Mar-14 22:01:25 LOG5 end_task: Level: (2) ID = <10104> Status = 0 0 0 0 ok 2009-Mar-14 22:01:25 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'adjpwrif2' 2009-Mar-14 22:01:25 START begin_task: Starting task 'adjusting WAPP power' 2009-Mar-14 22:01:25 LOG5 begin_task: Level: (2) ID = <10105> Status = 0 0 0 0 ok 2009-Mar-14 22:01:25 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Adjusting WAPP Power} TASKWAIT BITMAP stat_power INFO {Adjusting power ...} 2009-Mar-14 22:01:25 LOG3 sock_errsend: To WAPPCON: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 22:01:25 LOG3 sock_errsend: To WAPPCON2: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 22:01:25 LOG3 sock_errsend: To WAPPCON3: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 22:01:25 LOG3 sock_errsend: To WAPPCON4: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 22:01:25 START begin_task: Starting task 'waiting on adjust WAPP power' 2009-Mar-14 22:01:25 LOG5 begin_task: Level: (3) ID = <10106> Status = 0 0 0 0 ok 2009-Mar-14 22:01:25 LOG4 WAPP=1+2+3+4-wappcon: Received command 'ADJUSTPOWER 100 1 2 0 1 1' 2009-Mar-14 22:01:25 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:01:25 INFO2 WAPP=1-auto_atten_dual: Attenuators beam 0: 7 6 dB --- beam 1: 6 6 dB 2009-Mar-14 22:01:25 INFO2 WAPP=3-auto_atten_dual: Attenuators beam 4: 2 1 dB --- beam 5: 5 3 dB 2009-Mar-14 22:01:25 INFO2 WAPP=2-auto_atten_dual: Attenuators beam 2: 6 4 dB --- beam 3: 3 3 dB 2009-Mar-14 22:01:25 INFO2 WAPP=4-auto_atten_dual: Attenuators beam 6: 3 0 dB --- beam 7: 2 0 dB 2009-Mar-14 22:01:25 INFO1 WAPP=1+2+3+4-adjust_power: DONE adjusting power 2009-Mar-14 22:01:25 STOP end_task: Finishing task 'waiting on adjust WAPP power' with status 'OK' 2009-Mar-14 22:01:25 LOG5 end_task: Level: (3) ID = <10106> Status = 0 0 0 0 ok 2009-Mar-14 22:01:26 INFO2 wapp_adjpwr: WAPP power: ALFA beam 0: 0.920 0.921 ALFA beam 1: 1.037 1.058 2009-Mar-14 22:01:26 INFO2 wapp_adjpwr: WAPP power: ALFA beam 2: 1.019 0.967 ALFA beam 3: 1.071 0.880 2009-Mar-14 22:01:26 INFO2 wapp_adjpwr: WAPP power: ALFA beam 4: 1.091 0.950 ALFA beam 5: 1.004 0.893 2009-Mar-14 22:01:26 INFO2 wapp_adjpwr: WAPP power: ALFA beam 6: 0.916 0.107 ALFA beam 7: 1.017 0.116 2009-Mar-14 22:01:26 STOP finish_task: Finishing task 'adjusting WAPP power' 2009-Mar-14 22:01:26 LOG5 finish_task: Level: (2) ID = <10105> Status = 0 0 0 0 ok 2009-Mar-14 22:01:26 INFO2 finish_task: DONE finished adjusting: WAPP power 2009-Mar-14 22:01:26 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 22:01:26 STOP end_task: Finishing task 'adjusting WAPP power' with status 'OK' 2009-Mar-14 22:01:26 LOG5 end_task: Level: (2) ID = <10105> Status = 0 0 0 0 ok 2009-Mar-14 22:01:26 LOG4 send_obs_status: To obs_status: <1> BITMAP stat_busy 2009-Mar-14 22:01:26 STOP finish_task: Finishing task 'adjusting WAPP power' 2009-Mar-14 22:01:26 LOG5 finish_task: Level: (1) ID = <10103> Status = 0 0 0 0 ok 2009-Mar-14 22:01:26 DONE finish_task: DONE finished adjusting: WAPP power levels 2009-Mar-14 22:01:26 LOG4 send_obs_status: To obs_status: <1> ENDTASK Finished 2009-Mar-14 22:01:26 END end_task: Finishing task 'adjusting WAPP power' with status 'OK' 2009-Mar-14 22:01:26 LOG5 end_task: Level: (1) ID = <10103> Status = 0 0 0 0 ok 2009-Mar-14 22:01:27 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.107 < 0.75)! 2009-Mar-14 22:01:27 LOG4 check_wapp_levels: WAPP-1 power levels: 0.920 0.921 1.037 1.058 2009-Mar-14 22:01:27 LOG4 check_wapp_levels: WAPP-2 power levels: 1.019 0.967 1.071 0.880 2009-Mar-14 22:01:27 LOG4 check_wapp_levels: WAPP-3 power levels: 1.091 0.950 1.004 0.893 2009-Mar-14 22:01:27 LOG4 check_wapp_levels: WAPP-4 power levels: 0.916 0.107 1.017 0.116 2009-Mar-14 22:01:43 COMMAND CIMA-send_to_exec: Sending command to run fixed azimuth drift map 2009-Mar-14 22:01:43 LOG4 exec_msg: From OBSERVER: fixed_driftmap follow 99 600 180.0 19.0 hcorcal 1 loopend-ON no off lcorcal first 1 drift90p2 090400.0 +215400 J 0 Topocentric velocity(optical) 2009-Mar-14 22:01:43 LOG1 fixed_driftmap: Calling 'fixed_driftmap follow 99 600 180.0 19.0 hcorcal 1 loopend-ON no off lcorcal first 1 drift90p2 090400.0 +215400 J 0 Topocentric velocity(optical)' 2009-Mar-14 22:01:43 BEGIN begin_task: Starting task 'fixed azimuth drift map' 2009-Mar-14 22:01:43 LOG5 begin_task: Level: (1) ID = <10107> Status = 0 0 0 0 ok 2009-Mar-14 22:01:43 INFO4 begin_task: MAKING 'fixed azimuth drift map' using 'alfa' + 'WAPP' on 'galfasrc' 2009-Mar-14 22:01:43 INFO1 fixed_driftmap: Starting pattern: Fixed azimuth drift map 2009-Mar-14 22:01:43 LOG4 send_obs_status: To obs_status: <1> NEWTASK {Fixed azimuth drift map} TOTALLOOPS 99 INFO {Starting fixed azimuth drift map observation ...} SOURCE {drift90p2} 2009-Mar-14 22:01:43 INFO5 fixed_driftmap: Start: year = 2009.2023760678887 RA = 09:04:33.9 Dec = +21:51:44.2 2009-Mar-14 22:01:43 NOTE fixed_driftmap: Setting ZA to 3:30:30.5 ... 2009-Mar-14 22:01:43 INFO3 fixed_driftmap: Sending telescope to Az = 180.00 and ZA = 3.51 2009-Mar-14 22:01:43 LOG3 track_source: Calling 'track_source drift90p2 180.0 3.5084714710 F 0.0 0.0 main small {} 0 Topocentric velocity(optical)' 2009-Mar-14 22:01:43 START begin_task: Starting task 'sending tracking commands' 2009-Mar-14 22:01:43 LOG5 begin_task: Level: (2) ID = <10108> Status = 0 0 0 0 ok 2009-Mar-14 22:01:44 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Sending Tracking Commands} SOURCE {drift90p2} INFO {Slewing to source 'drift90p2' ...} 2009-Mar-14 22:01:44 INFO1 track_source: Starting to track drift90p2 2009-Mar-14 22:01:44 LOG3 vw_send: To DATATAKING: hdrldsrcnm "drift90p2" 2009-Mar-14 22:01:44 LOG3 vw_send: To DATATAKING: set ra 180.0 2009-Mar-14 22:01:44 LOG3 vw_send: To DATATAKING: set dec 3.5084714710 2009-Mar-14 22:01:44 LOG3 vw_send: To DATATAKING: pnt tr send 2009-Mar-14 22:01:44 LOG3 vw_send: To DATATAKING: pnt tr 180.0 3.5084714710 -CF 2009-Mar-14 22:01:44 LOG3 vw_send: To DATATAKING: dopsetvel 0 topo 2009-Mar-14 22:01:44 STOP finish_task: Finishing task 'sending tracking commands' 2009-Mar-14 22:01:44 LOG5 finish_task: Level: (2) ID = <10108> Status = 0 0 0 0 ok 2009-Mar-14 22:01:44 INFO2 finish_task: DONE finished sending: tracking commands 2009-Mar-14 22:01:44 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 22:01:44 STOP end_task: Finishing task 'sending tracking commands' with status 'OK' 2009-Mar-14 22:01:44 LOG5 end_task: Level: (2) ID = <10108> Status = 0 0 0 0 ok 2009-Mar-14 22:01:44 START begin_task: Starting task 'rotate ALFA to +19 degrees' 2009-Mar-14 22:01:44 LOG5 begin_task: Level: (2) ID = <10109> Status = 0 0 0 0 ok 2009-Mar-14 22:01:44 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Rotating ALFA} INFO {Rotating ALFA to +19 degrees ...} 2009-Mar-14 22:01:44 INFO2 rotate_alfa: ALFA commanded to +19.0 degrees 2009-Mar-14 22:01:44 LOG3 sock_errsend: To ALFAMOTOR: POSITION 19.0 REPLY 2009-Mar-14 22:01:44 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_alfa_rot MESSAGE {Waiting for ALFA to rotate into position ...} 2009-Mar-14 22:01:44 START begin_task: Starting task 'waiting on ALFA rotation' 2009-Mar-14 22:01:44 LOG5 begin_task: Level: (3) ID = <10110> Status = 0 0 0 0 ok 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: hdrldsrcnm "drift90p2" 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: set ra 180.0 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: set dec 3.5084714710 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: vw% 180.0 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: vw% 3.5084714710 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: pnt tr send 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: pnt tr 180.0 3.5084714710 -CF 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: dopsetvel 0 topo 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: vw% vw% 2009-Mar-14 22:01:44 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:01:45 LOG4 exec_msg: From ALFAMOTOR: alfa_motor "INPOSITION" 2009-Mar-14 22:01:45 INFO3 alfa_motor: ALFA rotator in-position +19.00 degrees 2009-Mar-14 22:01:45 STOP end_task: Finishing task 'waiting on ALFA rotation' with status 'OK' 2009-Mar-14 22:01:45 LOG5 end_task: Level: (3) ID = <10110> Status = 0 0 0 0 ok 2009-Mar-14 22:01:45 LOG4 send_obs_status: To obs_status: <0> CLEARTIME BITMAP stat_busy 2009-Mar-14 22:01:45 STOP finish_task: Finishing task 'rotate ALFA to +19 degrees' 2009-Mar-14 22:01:45 LOG5 finish_task: Level: (2) ID = <10109> Status = 0 0 0 0 ok 2009-Mar-14 22:01:45 INFO2 finish_task: DONE finished configuration: rotating ALFA to +19 degrees 2009-Mar-14 22:01:45 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 22:01:45 STOP end_task: Finishing task 'rotate ALFA to +19 degrees' with status 'OK' 2009-Mar-14 22:01:45 LOG5 end_task: Level: (2) ID = <10109> Status = 0 0 0 0 ok 2009-Mar-14 22:01:45 START begin_task: Starting task 'waiting on telescope' 2009-Mar-14 22:01:45 LOG5 begin_task: Level: (2) ID = <10111> Status = 0 0 0 0 ok 2009-Mar-14 22:01:45 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Waiting On Telescope} TASKWAIT BITMAP stat_slew INFO {Waiting for telescope to track source ...} 2009-Mar-14 22:01:45 LOG3 waittrk: Start waittrk 5 2009-Mar-14 22:01:45 START begin_task: Starting task 'waiting on telescope movement' 2009-Mar-14 22:01:45 LOG5 begin_task: Level: (3) ID = <10112> Status = 0 0 0 0 ok 2009-Mar-14 22:01:50 STOP end_task: Finishing task 'waiting on telescope movement' with status 'OK' 2009-Mar-14 22:01:50 LOG5 end_task: Level: (3) ID = <10112> Status = 0 0 0 0 ok 2009-Mar-14 22:01:50 START begin_task: Starting task 'waiting on telescope on source' 2009-Mar-14 22:01:50 LOG5 begin_task: Level: (3) ID = <10113> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 STOP end_task: Finishing task 'waiting on telescope on source' with status 'OK' 2009-Mar-14 22:03:01 LOG5 end_task: Level: (3) ID = <10113> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 LOG4 send_obs_status: To obs_status: <0> CLEARTIME BITMAP stat_busy 2009-Mar-14 22:03:01 INFO2 waittrk: Now tracking drift90p2 2009-Mar-14 22:03:01 LOG4 waittrk: Current telescope position: Az = 179.72 ZA = 3.53 2009-Mar-14 22:03:01 STOP finish_task: Finishing task 'waiting on telescope' 2009-Mar-14 22:03:01 LOG5 finish_task: Level: (2) ID = <10111> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 INFO2 finish_task: DONE finished waiting: telescope on source 2009-Mar-14 22:03:01 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 22:03:01 STOP end_task: Finishing task 'waiting on telescope' with status 'OK' 2009-Mar-14 22:03:01 LOG5 end_task: Level: (2) ID = <10111> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 START begin_task: Starting task 'selecting calibration type' 2009-Mar-14 22:03:01 LOG5 begin_task: Level: (2) ID = <10114> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 LOG3 vw_send: To DATATAKING: setcal hcorcal 2009-Mar-14 22:03:01 LOG2 socket_wait: Starting sockwait on DATATAKING for 'setcal' using string 'DONE' 2009-Mar-14 22:03:01 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:03:01 START begin_task: Starting task 'waiting on setcal' 2009-Mar-14 22:03:01 LOG5 begin_task: Level: (3) ID = <10115> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 LOG4 got_cormsg: From DATATAKING: setcal hcorcal 2009-Mar-14 22:03:01 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:03:01 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:03:01 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 22:03:01 STOP end_task: Finishing task 'waiting on setcal' with status 'OK' 2009-Mar-14 22:03:01 LOG5 end_task: Level: (3) ID = <10115> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'setcal' 2009-Mar-14 22:03:01 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:03:01 LOG3 socket_wait: To ALFAMON: CAL HI 2009-Mar-14 22:03:01 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:03:01 LOG5 begin_task: Level: (3) ID = <10116> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:03:01 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:03:01 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:03:01 LOG5 end_task: Level: (3) ID = <10116> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:03:01 LOG3 to_alfamon: To ALFAMON: CAL HI 2009-Mar-14 22:03:01 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:03:01 LOG3 socket_wait: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:03:01 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:03:01 LOG5 begin_task: Level: (3) ID = <10117> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:03:01 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:03:01 LOG5 end_task: Level: (3) ID = <10117> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:03:01 LOG3 to_alfamon: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:03:01 STOP end_task: Finishing task 'selecting calibration type' with status 'OK' 2009-Mar-14 22:03:01 LOG5 end_task: Level: (2) ID = <10114> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 LOG5 dopset_later: Calling 'dopset_later 0' 2009-Mar-14 22:03:01 INFO3 dopset_later: Setting Doppler correction now 2009-Mar-14 22:03:01 LOG5 antvel: Calling 'antvel 180.000000 3.508471 F Topocentric 0' 2009-Mar-14 22:03:01 LOG2 antvel: Transforming current Az = 180.00 ZA = 3.51 to apparent RA = 09:07:15.7 Dec = +21:51:44.2 2009-Mar-14 22:03:01 LOG2 antvel: Parameters to Doppler: Topocentric 93781 2009 73 0.0 2009-Mar-14 22:03:01 INFO5 antvel: Computed antenna velocity: +0.00000 km/s 2009-Mar-14 22:03:01 LOG3 dopset_gen: Parameters for 'rest2sky': vel=0.000000 veltype=velocity(optical) calctype=SUBBAND antvel=0.0 restcent=1385.0 rest0=1385.0 rest1=1385.0 rest2=1385.0 rest3=1385.0 rest4=1385.0 rest5=1385.0 rest6=1385.0 rest7=1385.0 2009-Mar-14 22:03:01 INFO4 dopset_gen: New sky frequencies: 1385.000000 1385.000000 1385.000000 1385.000000 1385.000000 1385.000000 1385.000000 1385.000000 1385.000000 2009-Mar-14 22:03:01 LOG3 dopset_gen: Parameters for 'sky2syn': skycent=1385.000000 sky0=1385.000000 sky1=1385.000000 sky2=1385.000000 sky3=1385.000000 sky4=1385.000000 sky5=1385.000000 sky6=1385.000000 sky7=1385.000000 dest0=250 dest1=250 dest2=250 dest3=250 dest4=250 dest5=250 dest6=250 dest7=250 2009-Mar-14 22:03:01 LOG2 dopset_gen: Result from 'sky2syn': 1635.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 2009-Mar-14 22:03:01 LOG3 vw_send: To DATATAKING: if1 {if1_syn1 1635000000.0} 2009-Mar-14 22:03:01 LOG3 vw_send: To DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 22:03:01 START begin_task: Starting task 'adjusting WAPP power' 2009-Mar-14 22:03:01 LOG5 begin_task: Level: (2) ID = <10118> Status = 0 0 0 0 ok 2009-Mar-14 22:03:01 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Adjusting WAPP power} TASKWAIT BITMAP stat_power INFO {Adjusting WAPP power ...} 2009-Mar-14 22:03:01 INFO2 adjust_power: Starting to adjust WAPP power 2009-Mar-14 22:03:01 LOG3 vw_send: To DATATAKING: adjpwrif2 2009-Mar-14 22:03:02 LOG2 socket_wait: Starting sockwait on DATATAKING for 'adjpwrif2' using string 'DONE' 2009-Mar-14 22:03:02 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:03:02 START begin_task: Starting task 'waiting on adjpwrif2' 2009-Mar-14 22:03:02 LOG5 begin_task: Level: (3) ID = <10119> Status = 0 0 0 0 ok 2009-Mar-14 22:03:02 LOG4 got_cormsg: From DATATAKING: if1 {if1_syn1 1635000000.0} 2009-Mar-14 22:03:02 LOG4 got_cormsg: From DATATAKING: if2 {if2_synfrq 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0} 2009-Mar-14 22:03:02 LOG4 got_cormsg: From DATATAKING: adjpwrif2 2009-Mar-14 22:03:02 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:03:02 LOG4 got_cormsg: From DATATAKING: vw% vw% 2009-Mar-14 22:03:05 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:03:05 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 22:03:05 STOP end_task: Finishing task 'waiting on adjpwrif2' with status 'OK' 2009-Mar-14 22:03:05 LOG5 end_task: Level: (3) ID = <10119> Status = 0 0 0 0 ok 2009-Mar-14 22:03:05 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'adjpwrif2' 2009-Mar-14 22:03:05 START begin_task: Starting task 'adjusting WAPP power' 2009-Mar-14 22:03:05 LOG5 begin_task: Level: (3) ID = <10120> Status = 0 0 0 0 ok 2009-Mar-14 22:03:05 LOG4 send_obs_status: To obs_status: <0> NEWTASK {Adjusting WAPP Power} TASKWAIT BITMAP stat_power INFO {Adjusting power ...} 2009-Mar-14 22:03:05 LOG3 sock_errsend: To WAPPCON: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 22:03:05 LOG3 sock_errsend: To WAPPCON2: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 22:03:05 LOG3 sock_errsend: To WAPPCON3: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 22:03:05 LOG3 sock_errsend: To WAPPCON4: ADJUSTPOWER 100 1 2 0 1 1 2009-Mar-14 22:03:05 START begin_task: Starting task 'waiting on adjust WAPP power' 2009-Mar-14 22:03:05 LOG5 begin_task: Level: (4) ID = <10121> Status = 0 0 0 0 ok 2009-Mar-14 22:03:05 LOG4 WAPP=1+2+3+4-wappcon: Received command 'ADJUSTPOWER 100 1 2 0 1 1' 2009-Mar-14 22:03:05 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:03:05 INFO2 WAPP=1-auto_atten_dual: Attenuators beam 0: 7 6 dB --- beam 1: 6 6 dB 2009-Mar-14 22:03:05 INFO2 WAPP=3-auto_atten_dual: Attenuators beam 4: 3 1 dB --- beam 5: 5 3 dB 2009-Mar-14 22:03:05 INFO2 WAPP=2-auto_atten_dual: Attenuators beam 2: 6 4 dB --- beam 3: 3 3 dB 2009-Mar-14 22:03:05 INFO2 WAPP=4-auto_atten_dual: Attenuators beam 6: 3 0 dB --- beam 7: 2 0 dB 2009-Mar-14 22:03:05 INFO1 WAPP=1+2+3+4-adjust_power: DONE adjusting power 2009-Mar-14 22:03:05 STOP end_task: Finishing task 'waiting on adjust WAPP power' with status 'OK' 2009-Mar-14 22:03:05 LOG5 end_task: Level: (4) ID = <10121> Status = 0 0 0 0 ok 2009-Mar-14 22:03:05 INFO2 wapp_adjpwr: WAPP power: ALFA beam 0: 0.925 0.927 ALFA beam 1: 1.050 1.061 2009-Mar-14 22:03:05 INFO2 wapp_adjpwr: WAPP power: ALFA beam 2: 1.022 0.964 ALFA beam 3: 1.104 0.899 2009-Mar-14 22:03:05 INFO2 wapp_adjpwr: WAPP power: ALFA beam 4: 0.897 0.982 ALFA beam 5: 1.034 0.931 2009-Mar-14 22:03:05 INFO2 wapp_adjpwr: WAPP power: ALFA beam 6: 0.933 0.109 ALFA beam 7: 1.031 0.118 2009-Mar-14 22:03:05 STOP finish_task: Finishing task 'adjusting WAPP power' 2009-Mar-14 22:03:05 LOG5 finish_task: Level: (3) ID = <10120> Status = 0 0 0 0 ok 2009-Mar-14 22:03:05 INFO3 finish_task: DONE finished adjusting: WAPP power 2009-Mar-14 22:03:05 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 22:03:05 STOP end_task: Finishing task 'adjusting WAPP power' with status 'OK' 2009-Mar-14 22:03:05 LOG5 end_task: Level: (3) ID = <10120> Status = 0 0 0 0 ok 2009-Mar-14 22:03:05 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_busy 2009-Mar-14 22:03:05 STOP finish_task: Finishing task 'adjusting WAPP power' 2009-Mar-14 22:03:05 LOG5 finish_task: Level: (2) ID = <10118> Status = 0 0 0 0 ok 2009-Mar-14 22:03:05 INFO2 finish_task: DONE finished adjusting: WAPP power levels 2009-Mar-14 22:03:05 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 22:03:05 STOP end_task: Finishing task 'adjusting WAPP power' with status 'OK' 2009-Mar-14 22:03:05 LOG5 end_task: Level: (2) ID = <10118> Status = 0 0 0 0 ok 2009-Mar-14 22:03:05 LOG1 fixed_driftmap: Parameters: HA = +00:00:00.0 Start = 09:04:33.9 LST = 09:07:19.7 diff = -165.8 secs 2009-Mar-14 22:03:05 WARNING fixed_driftmap: WARNING RA has already passed --- starting anyway! 2009-Mar-14 22:03:05 LOG3 send_to_one_wapp: To WAPPCON: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:03:05 LOG3 send_to_one_wapp: To WAPPCON2: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:03:05 LOG3 send_to_one_wapp: To WAPPCON3: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:03:06 LOG3 send_to_one_wapp: To WAPPCON4: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:03:06 INFO2 fixed_driftmap: Starting fixed azimuth drift map loop 1 of 99 2009-Mar-14 22:03:06 LOG4 send_obs_status: To obs_status: <1> LOOP 1 2009-Mar-14 22:03:06 LOG4 send_obs_status: To obs_status: <1> INFO {Making drift scan followed by CAL} 2009-Mar-14 22:03:06 LOG4 take_data: Calling 'take_data 600 1 FIXEDAZ FIXEDAZ stat_drift {drift scan}' 2009-Mar-14 22:03:06 START begin_task: Starting task 'WAPP spectral observation' 2009-Mar-14 22:03:06 LOG5 begin_task: Level: (2) ID = <10122> Status = 0 0 0 0 ok 2009-Mar-14 22:03:06 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for drift scan ...} 2009-Mar-14 22:03:06 LOG5 log_alfabeam: Can't log alfabeam, not J2000 2009-Mar-14 22:03:06 INFO2 take_data: Starting WAPP 600-second scan: 907300173 2009-Mar-14 22:03:06 START begin_task: Starting task 'waiting on WAPP spectra' 2009-Mar-14 22:03:06 LOG5 begin_task: Level: (3) ID = <10123> Status = 0 0 0 0 ok 2009-Mar-14 22:03:06 LOG4 WAPP=1+2+3+4-wappcon: Received command 'PROJECT a2010 Lyle Hoffman' 2009-Mar-14 22:03:06 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 22:03:06 LOG4 send_obs_status: To obs_status: <0> TASKTIME 600 BITMAP stat_drift MESSAGE {Taking drift scan ...} 2009-Mar-14 22:03:06 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7387.00 2009-Mar-14 22:03:06 NOTE WAPPDATA-new_file: New FITS file: wapp.20090314.a2010.0030.fits 2009-Mar-14 22:03:06 LOG4 send_obs_status: To obs_status: <0> FILENAME {wapp.20090314.a2010.0030.fits} 2009-Mar-14 22:03:08 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.000000 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 22:03:08 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:03:08 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:03:08 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 22:03:08 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 22:03:08 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:03:08 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:03:08 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:03:08 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:03:08 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:03:08 LOG4 check_wapp_levels: WAPP-1 power levels: 0.928 0.921 1.043 1.057 2009-Mar-14 22:03:08 LOG4 check_wapp_levels: WAPP-2 power levels: 1.022 0.965 1.100 0.898 2009-Mar-14 22:03:08 LOG4 check_wapp_levels: WAPP-3 power levels: 0.894 0.978 1.033 0.929 2009-Mar-14 22:03:08 LOG4 check_wapp_levels: WAPP-4 power levels: 0.932 0.109 1.029 0.118 2009-Mar-14 22:03:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:03:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:03:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:22 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 11 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:03:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:03:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:27 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 15 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:03:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:03:30 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 11 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:03:30 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 15 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:03:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:03:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:03:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:03:38 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:03:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:03:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.098 (still bad) 2009-Mar-14 22:03:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:03:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:03:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:03:59 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 13 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:04:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:04:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:04:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:04:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:04:08 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:04:09 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:04:09 LOG4 check_wapp_levels: WAPP-1 power levels: 0.930 0.926 1.042 1.058 2009-Mar-14 22:04:09 LOG4 check_wapp_levels: WAPP-2 power levels: 1.023 0.966 1.105 0.903 2009-Mar-14 22:04:09 LOG4 check_wapp_levels: WAPP-3 power levels: 0.894 0.980 1.015 0.914 2009-Mar-14 22:04:09 LOG4 check_wapp_levels: WAPP-4 power levels: 0.935 0.109 1.031 0.118 2009-Mar-14 22:04:09 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 8 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:04:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:04:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:04:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:04:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:04:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:04:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:04:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.119 (still bad) 2009-Mar-14 22:04:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.133 (still bad) 2009-Mar-14 22:04:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.136 (still bad) 2009-Mar-14 22:04:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.140 (still bad) 2009-Mar-14 22:04:30 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 11 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:04:31 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 13 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:04:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.141 (still bad) 2009-Mar-14 22:04:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.138 (still bad) 2009-Mar-14 22:04:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.129 (still bad) 2009-Mar-14 22:04:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.126 (still bad) 2009-Mar-14 22:04:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:04:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:04:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:04:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:04:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:04:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:04:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:04:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:04:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:04:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:04:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:05:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:05:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:11 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:05:12 LOG4 check_wapp_levels: WAPP-1 power levels: 0.926 0.920 1.047 1.059 2009-Mar-14 22:05:12 LOG4 check_wapp_levels: WAPP-2 power levels: 1.023 0.964 1.100 0.897 2009-Mar-14 22:05:12 LOG4 check_wapp_levels: WAPP-3 power levels: 0.894 0.977 1.030 0.924 2009-Mar-14 22:05:12 LOG4 check_wapp_levels: WAPP-4 power levels: 0.935 0.109 1.032 0.118 2009-Mar-14 22:05:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:05:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:05:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:05:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.098 (still bad) 2009-Mar-14 22:05:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:05:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:05:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:05:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:05:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:05:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:05:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.097 (still bad) 2009-Mar-14 22:05:44 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 13 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:05:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:05:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:05:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:05:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:05:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:06:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:06:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:06:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.098 (still bad) 2009-Mar-14 22:06:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.098 (still bad) 2009-Mar-14 22:06:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:06:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:06:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:06:14 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:06:14 LOG4 check_wapp_levels: WAPP-1 power levels: 0.929 0.925 1.046 1.061 2009-Mar-14 22:06:14 LOG4 check_wapp_levels: WAPP-2 power levels: 1.027 0.969 1.103 0.901 2009-Mar-14 22:06:14 LOG4 check_wapp_levels: WAPP-3 power levels: 0.896 0.982 1.023 0.917 2009-Mar-14 22:06:14 LOG4 check_wapp_levels: WAPP-4 power levels: 0.936 0.109 1.032 0.118 2009-Mar-14 22:06:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.097 (still bad) 2009-Mar-14 22:06:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:06:20 LOG4 exec_msg: From SCRAMWAPPDATA: log_message INFO4 WAPPDATA-queue_agcdata {Received duplicate AGC-datablock at 22:06:20.301 (seconds: 79580.301)!} 2009-Mar-14 22:06:20 INFO4 WAPPDATA-queue_agcdata: Received duplicate AGC-datablock at 22:06:20.301 (seconds: 79580.301)! 2009-Mar-14 22:06:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:06:21 INFO4 WAPPDATA-search_agc: Extrapolating agc-data from 79579.0 to 79580.0! 2009-Mar-14 22:06:22 INFO4 WAPPDATA-search_agc: Interpolating agc-data over 2.00 second time gap (79579.0 - 79581.0)! 2009-Mar-14 22:06:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:06:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:06:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:06:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:06:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:06:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:06:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:06:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:06:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:06:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:06:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:06:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:06:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:06:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:06:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:06:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:06:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:06:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:06:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:07:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:07:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:07:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:07:15 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:07:15 LOG4 check_wapp_levels: WAPP-1 power levels: 0.924 0.922 1.048 1.057 2009-Mar-14 22:07:15 LOG4 check_wapp_levels: WAPP-2 power levels: 1.024 0.964 1.100 0.898 2009-Mar-14 22:07:15 LOG4 check_wapp_levels: WAPP-3 power levels: 0.895 0.980 1.019 0.914 2009-Mar-14 22:07:15 LOG4 check_wapp_levels: WAPP-4 power levels: 0.933 0.109 1.028 0.118 2009-Mar-14 22:07:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:07:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:07:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.098 (still bad) 2009-Mar-14 22:07:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:07:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:07:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:07:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:07:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:07:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:07:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:07:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:07:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:07:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:07:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:07:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:07:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:08:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:08:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:08:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:08:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:08:16 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:08:16 LOG4 check_wapp_levels: WAPP-1 power levels: 0.926 0.922 1.044 1.055 2009-Mar-14 22:08:16 LOG4 check_wapp_levels: WAPP-2 power levels: 1.022 0.965 1.101 0.894 2009-Mar-14 22:08:16 LOG4 check_wapp_levels: WAPP-3 power levels: 0.892 0.977 1.017 0.913 2009-Mar-14 22:08:16 LOG4 check_wapp_levels: WAPP-4 power levels: 0.931 0.109 1.026 0.118 2009-Mar-14 22:08:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:08:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:08:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:08:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:08:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:08:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:08:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:08:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:08:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:08:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:08:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:08:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:08:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:09:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:09:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:09:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:09:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:09:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:18 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:09:18 LOG4 check_wapp_levels: WAPP-1 power levels: 0.925 0.924 1.047 1.056 2009-Mar-14 22:09:18 LOG4 check_wapp_levels: WAPP-2 power levels: 1.035 0.975 1.103 0.897 2009-Mar-14 22:09:18 LOG4 check_wapp_levels: WAPP-3 power levels: 0.894 0.977 1.021 0.917 2009-Mar-14 22:09:18 LOG4 check_wapp_levels: WAPP-4 power levels: 0.940 0.109 1.037 0.118 2009-Mar-14 22:09:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:09:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:09:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:09:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:09:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:09:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:09:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:09:46 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:09:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:09:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:09:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:09:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:09:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:09:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.099 (still bad) 2009-Mar-14 22:10:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:10:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:10:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:10:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:10:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:10:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:10:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:10:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:10:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:10:19 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:10:19 LOG4 check_wapp_levels: WAPP-1 power levels: 0.929 0.927 1.047 1.055 2009-Mar-14 22:10:19 LOG4 check_wapp_levels: WAPP-2 power levels: 1.025 0.964 1.102 0.899 2009-Mar-14 22:10:19 LOG4 check_wapp_levels: WAPP-3 power levels: 0.893 0.978 1.034 0.927 2009-Mar-14 22:10:19 LOG4 check_wapp_levels: WAPP-4 power levels: 0.937 0.109 1.033 0.118 2009-Mar-14 22:10:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:10:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:10:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:10:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:10:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:10:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:10:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:10:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:10:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:10:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:10:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:10:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:10:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:10:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:10:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:10:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:10:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:10:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:10:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:11:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:11:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:11:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:11:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:11:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:11:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:11:20 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:11:20 LOG4 check_wapp_levels: WAPP-1 power levels: 0.925 0.928 1.050 1.059 2009-Mar-14 22:11:20 LOG4 check_wapp_levels: WAPP-2 power levels: 1.031 0.971 1.102 0.901 2009-Mar-14 22:11:20 LOG4 check_wapp_levels: WAPP-3 power levels: 0.896 0.976 1.025 0.921 2009-Mar-14 22:11:20 LOG4 check_wapp_levels: WAPP-4 power levels: 0.935 0.109 1.032 0.118 2009-Mar-14 22:11:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:11:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:11:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:11:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:11:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:11:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:11:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:11:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:11:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:11:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:11:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:11:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:12:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:12:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:12:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:12:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.100 (still bad) 2009-Mar-14 22:12:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:23 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:12:23 LOG4 check_wapp_levels: WAPP-1 power levels: 0.927 0.925 1.047 1.056 2009-Mar-14 22:12:23 LOG4 check_wapp_levels: WAPP-2 power levels: 1.025 0.969 1.101 0.895 2009-Mar-14 22:12:23 LOG4 check_wapp_levels: WAPP-3 power levels: 0.894 0.977 1.019 0.915 2009-Mar-14 22:12:23 LOG4 check_wapp_levels: WAPP-4 power levels: 0.934 0.109 1.031 0.118 2009-Mar-14 22:12:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:12:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:12:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:12:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:12:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:12:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:12:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:12:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:12:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.101 (still bad) 2009-Mar-14 22:13:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:13:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:13:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:13:07 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 22:13:07 STOP end_task: Finishing task 'waiting on WAPP spectra' with status 'OK' 2009-Mar-14 22:13:07 LOG5 end_task: Level: (3) ID = <10123> Status = 0 0 0 0 ok 2009-Mar-14 22:13:07 STOP end_task: Finishing task 'WAPP spectral observation' with status 'OK' 2009-Mar-14 22:13:07 LOG5 end_task: Level: (2) ID = <10122> Status = 0 0 0 0 ok 2009-Mar-14 22:13:07 LOG1 fixed_driftmap: New position: year = 2009.2023977425406 RA = 09:16:50.5 RA/Dec = 09:17:24.2 +21:51:36.5 2009-Mar-14 22:13:07 NOTE fixed_driftmap: Correcting ZA to 3:30:22.8 ... 2009-Mar-14 22:13:07 LOG3 vw_send: To DATATAKING: pnt tr -UD 180.0 3.5063227623 -CF 2009-Mar-14 22:13:07 LOG2 take_cal: Calling 'take_cal hcorcal 1 1' 2009-Mar-14 22:13:07 START begin_task: Starting task 'WAPP calibration' 2009-Mar-14 22:13:07 LOG5 begin_task: Level: (2) ID = <10124> Status = 0 0 0 0 ok 2009-Mar-14 22:13:07 LOG4 send_obs_status: To obs_status: <0> NEWTASK {WAPP Calibration} INFO {Making WAPP calibration ...} 2009-Mar-14 22:13:07 START begin_task: Starting task 'selecting calibration type' 2009-Mar-14 22:13:07 LOG5 begin_task: Level: (3) ID = <10125> Status = 0 0 0 0 ok 2009-Mar-14 22:13:07 LOG3 vw_send: To DATATAKING: setcal hcorcal 2009-Mar-14 22:13:07 LOG2 socket_wait: Starting sockwait on DATATAKING for 'setcal' using string 'DONE' 2009-Mar-14 22:13:07 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:13:07 START begin_task: Starting task 'waiting on setcal' 2009-Mar-14 22:13:07 LOG5 begin_task: Level: (4) ID = <10126> Status = 0 0 0 0 ok 2009-Mar-14 22:13:07 LOG4 got_cormsg: From DATATAKING: pnt tr -UD 180.0 3.5063227623 -CF 2009-Mar-14 22:13:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:13:07 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:13:07 LOG4 got_cormsg: From DATATAKING: setcal hcorcal 2009-Mar-14 22:13:07 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:13:07 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:13:07 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 22:13:07 STOP end_task: Finishing task 'waiting on setcal' with status 'OK' 2009-Mar-14 22:13:07 LOG5 end_task: Level: (4) ID = <10126> Status = 0 0 0 0 ok 2009-Mar-14 22:13:07 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'setcal' 2009-Mar-14 22:13:07 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:13:07 LOG3 socket_wait: To ALFAMON: CAL HI 2009-Mar-14 22:13:07 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:13:07 LOG5 begin_task: Level: (4) ID = <10127> Status = 0 0 0 0 ok 2009-Mar-14 22:13:07 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:13:08 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:13:08 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:13:08 LOG5 end_task: Level: (4) ID = <10127> Status = 0 0 0 0 ok 2009-Mar-14 22:13:08 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:13:08 LOG3 to_alfamon: To ALFAMON: CAL HI 2009-Mar-14 22:13:08 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:13:08 LOG3 socket_wait: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:13:08 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:13:08 LOG5 begin_task: Level: (4) ID = <10128> Status = 0 0 0 0 ok 2009-Mar-14 22:13:08 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:13:08 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:13:08 LOG5 end_task: Level: (4) ID = <10128> Status = 0 0 0 0 ok 2009-Mar-14 22:13:08 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:13:08 LOG3 to_alfamon: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:13:08 STOP end_task: Finishing task 'selecting calibration type' with status 'OK' 2009-Mar-14 22:13:08 LOG5 end_task: Level: (3) ID = <10125> Status = 0 0 0 0 ok 2009-Mar-14 22:13:08 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_cal_on MESSAGE {Setting CAL-ON ...} 2009-Mar-14 22:13:08 LOG3 wapp_calcontrol: To CALCONTROL: CALON 2009-Mar-14 22:13:08 LOG3 sock_errsend: To CALCONTROL: CALON STATUS 2009-Mar-14 22:13:08 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 22:13:08 LOG5 begin_task: Level: (3) ID = <10129> Status = 0 0 0 0 ok 2009-Mar-14 22:13:08 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 22:13:08 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x03 2009-Mar-14 22:13:08 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 22:13:08 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 22:13:08 LOG5 end_task: Level: (3) ID = <10129> Status = 0 0 0 0 ok 2009-Mar-14 22:13:08 LOG4 take_data: Calling 'take_data 1 1 CAL ON stat_cal_on {CAL-ON spectra}' 2009-Mar-14 22:13:08 START begin_task: Starting task 'WAPP spectral observation' 2009-Mar-14 22:13:08 LOG5 begin_task: Level: (3) ID = <10130> Status = 0 0 0 0 ok 2009-Mar-14 22:13:08 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON spectra ...} 2009-Mar-14 22:13:08 LOG5 log_alfabeam: Can't log alfabeam, not J2000 2009-Mar-14 22:13:08 INFO2 take_data: Starting WAPP 1-second scan: 907300174 2009-Mar-14 22:13:08 START begin_task: Starting task 'waiting on WAPP spectra' 2009-Mar-14 22:13:08 LOG5 begin_task: Level: (4) ID = <10131> Status = 0 0 0 0 ok 2009-Mar-14 22:13:08 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 22:13:08 LOG4 send_obs_status: To obs_status: <0> TASKTIME 1 BITMAP stat_cal_on MESSAGE {Taking CAL-ON spectra ...} 2009-Mar-14 22:13:08 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7989.00 2009-Mar-14 22:13:10 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.000000 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 22:13:10 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:13:10 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:13:10 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 22:13:10 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 22:13:10 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:13:10 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:13:10 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:13:10 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:13:10 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 22:13:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.545 (still bad) 2009-Mar-14 22:13:10 STOP end_task: Finishing task 'waiting on WAPP spectra' with status 'OK' 2009-Mar-14 22:13:10 LOG5 end_task: Level: (4) ID = <10131> Status = 0 0 0 0 ok 2009-Mar-14 22:13:10 STOP end_task: Finishing task 'WAPP spectral observation' with status 'OK' 2009-Mar-14 22:13:10 LOG5 end_task: Level: (3) ID = <10130> Status = 0 0 0 0 ok 2009-Mar-14 22:13:10 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_cal_off MESSAGE {Setting CAL-OFF ...} 2009-Mar-14 22:13:10 LOG3 wapp_calcontrol: To CALCONTROL: CALOFF 2009-Mar-14 22:13:10 LOG3 sock_errsend: To CALCONTROL: CALOFF STATUS 2009-Mar-14 22:13:10 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 22:13:10 LOG5 begin_task: Level: (3) ID = <10132> Status = 0 0 0 0 ok 2009-Mar-14 22:13:11 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 22:13:11 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 22:13:11 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 22:13:11 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 22:13:11 LOG5 end_task: Level: (3) ID = <10132> Status = 0 0 0 0 ok 2009-Mar-14 22:13:11 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_busy 2009-Mar-14 22:13:11 STOP finish_task: Finishing task 'WAPP calibration' 2009-Mar-14 22:13:11 LOG5 finish_task: Level: (2) ID = <10124> Status = 0 0 0 0 ok 2009-Mar-14 22:13:11 INFO2 finish_task: DONE finished calibration: WAPP calibration 2009-Mar-14 22:13:11 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 22:13:11 STOP end_task: Finishing task 'WAPP calibration' with status 'OK' 2009-Mar-14 22:13:11 LOG5 end_task: Level: (2) ID = <10124> Status = 0 0 0 0 ok 2009-Mar-14 22:13:11 INFO2 fixed_driftmap: Starting fixed azimuth drift map loop 2 of 99 2009-Mar-14 22:13:11 LOG4 send_obs_status: To obs_status: <1> LOOP 2 2009-Mar-14 22:13:11 LOG3 send_to_one_wapp: To WAPPCON: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:13:11 LOG3 send_to_one_wapp: To WAPPCON2: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:13:11 LOG3 send_to_one_wapp: To WAPPCON3: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:13:11 LOG3 send_to_one_wapp: To WAPPCON4: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:13:11 LOG4 send_obs_status: To obs_status: <1> INFO {Making drift scan followed by CAL} 2009-Mar-14 22:13:11 LOG4 take_data: Calling 'take_data 600 1 FIXEDAZ FIXEDAZ stat_drift {drift scan}' 2009-Mar-14 22:13:11 START begin_task: Starting task 'WAPP spectral observation' 2009-Mar-14 22:13:11 LOG5 begin_task: Level: (2) ID = <10133> Status = 0 0 0 0 ok 2009-Mar-14 22:13:11 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for drift scan ...} 2009-Mar-14 22:13:11 LOG5 log_alfabeam: Can't log alfabeam, not J2000 2009-Mar-14 22:13:11 INFO2 take_data: Starting WAPP 600-second scan: 907300175 2009-Mar-14 22:13:11 START begin_task: Starting task 'waiting on WAPP spectra' 2009-Mar-14 22:13:11 LOG5 begin_task: Level: (3) ID = <10134> Status = 0 0 0 0 ok 2009-Mar-14 22:13:11 LOG4 WAPP=1+2+3+4-wappcon: Received command 'PROJECT a2010 Lyle Hoffman' 2009-Mar-14 22:13:11 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 22:13:11 LOG4 send_obs_status: To obs_status: <0> TASKTIME 600 BITMAP stat_drift MESSAGE {Taking drift scan ...} 2009-Mar-14 22:13:11 INFO1 WAPP=1+2+3+4-start_spectra: start sec 7992.00 2009-Mar-14 22:13:11 NOTE WAPPDATA-new_file: New FITS file: wapp.20090314.a2010.0031.fits 2009-Mar-14 22:13:11 LOG4 send_obs_status: To obs_status: <0> FILENAME {wapp.20090314.a2010.0031.fits} 2009-Mar-14 22:13:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.545 (still bad) 2009-Mar-14 22:13:13 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.000000 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 22:13:13 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:13:13 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:13:13 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 22:13:13 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 22:13:13 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:13:13 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:13:13 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:13:13 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:13:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:13:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:13:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:13:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:13:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:13:25 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:13:25 LOG4 check_wapp_levels: WAPP-1 power levels: 0.926 0.928 1.048 1.057 2009-Mar-14 22:13:25 LOG4 check_wapp_levels: WAPP-2 power levels: 1.026 0.971 1.105 0.900 2009-Mar-14 22:13:25 LOG4 check_wapp_levels: WAPP-3 power levels: 0.892 0.975 1.021 0.917 2009-Mar-14 22:13:25 LOG4 check_wapp_levels: WAPP-4 power levels: 0.934 0.109 1.031 0.118 2009-Mar-14 22:13:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:13:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:13:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:13:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:13:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:13:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:13:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:13:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:13:42 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 11 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:13:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:13:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:13:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:13:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:13:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:13:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:13:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:13:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:13:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:14:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:14:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:14:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:14:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:14:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:14:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:14:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:14:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:14:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:14:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:14:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:14:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:14:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:14:27 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:14:27 LOG4 check_wapp_levels: WAPP-1 power levels: 0.927 0.932 1.052 1.059 2009-Mar-14 22:14:27 LOG4 check_wapp_levels: WAPP-2 power levels: 1.026 0.972 1.105 0.901 2009-Mar-14 22:14:27 LOG4 check_wapp_levels: WAPP-3 power levels: 0.896 0.981 1.024 0.920 2009-Mar-14 22:14:27 LOG4 check_wapp_levels: WAPP-4 power levels: 0.937 0.109 1.035 0.118 2009-Mar-14 22:14:29 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:14:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:14:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:14:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:14:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:14:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:14:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:14:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.102 (still bad) 2009-Mar-14 22:14:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:14:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:14:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:14:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:14:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:14:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:14:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:14:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:15:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:15:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:15:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:15:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:15:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:15:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:15:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:15:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:15:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:15:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:15:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:15:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:15:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:15:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:15:28 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:15:28 LOG4 check_wapp_levels: WAPP-1 power levels: 0.924 0.928 1.047 1.057 2009-Mar-14 22:15:28 LOG4 check_wapp_levels: WAPP-2 power levels: 1.026 0.969 1.103 0.903 2009-Mar-14 22:15:28 LOG4 check_wapp_levels: WAPP-3 power levels: 0.896 0.983 1.022 0.917 2009-Mar-14 22:15:28 LOG4 check_wapp_levels: WAPP-4 power levels: 0.936 0.109 1.031 0.118 2009-Mar-14 22:15:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:15:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:15:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:15:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:15:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:15:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:15:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:15:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:15:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:15:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:15:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:15:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:15:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:15:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:15:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:16:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:16:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:16:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:16:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:16:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:16:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:16:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:16:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:16:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:16:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:16:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:16:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:16:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:16:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:16:29 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:16:29 LOG4 check_wapp_levels: WAPP-1 power levels: 0.930 0.935 1.050 1.059 2009-Mar-14 22:16:29 LOG4 check_wapp_levels: WAPP-2 power levels: 1.027 0.973 1.107 0.904 2009-Mar-14 22:16:29 LOG4 check_wapp_levels: WAPP-3 power levels: 0.893 0.979 1.022 0.917 2009-Mar-14 22:16:29 LOG4 check_wapp_levels: WAPP-4 power levels: 0.948 0.109 1.046 0.118 2009-Mar-14 22:16:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:16:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:16:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:16:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:16:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:16:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:16:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:16:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:16:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:16:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:16:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:16:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:16:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:16:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:16:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:17:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:17:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:17:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:17:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:17:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:17:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:31 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:17:31 LOG4 check_wapp_levels: WAPP-1 power levels: 0.923 0.928 1.050 1.061 2009-Mar-14 22:17:31 LOG4 check_wapp_levels: WAPP-2 power levels: 1.027 0.972 1.107 0.902 2009-Mar-14 22:17:31 LOG4 check_wapp_levels: WAPP-3 power levels: 0.897 0.983 1.020 0.916 2009-Mar-14 22:17:31 LOG4 check_wapp_levels: WAPP-4 power levels: 0.943 0.109 1.040 0.118 2009-Mar-14 22:17:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:17:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:17:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:44 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 13 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:17:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:17:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:17:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:17:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:17:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:17:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:18:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:18:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:18:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:18:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:18:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:18:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:18:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:18:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:18:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:18:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:18:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:18:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:18:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:18:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:18:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:18:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:18:32 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:18:32 LOG4 check_wapp_levels: WAPP-1 power levels: 0.920 0.930 1.049 1.062 2009-Mar-14 22:18:32 LOG4 check_wapp_levels: WAPP-2 power levels: 1.029 0.976 1.109 0.904 2009-Mar-14 22:18:32 LOG4 check_wapp_levels: WAPP-3 power levels: 0.898 0.984 1.022 0.919 2009-Mar-14 22:18:32 LOG4 check_wapp_levels: WAPP-4 power levels: 0.938 0.109 1.034 0.119 2009-Mar-14 22:18:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:18:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:18:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:18:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:18:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:18:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:18:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:18:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:18:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:18:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:18:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:18:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:18:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:19:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:19:03 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:19:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:19:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:19:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:19:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:19:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:19:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:19:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:19:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:19:21 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:19:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:19:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:19:27 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:19:29 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:19:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:19:33 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:19:33 LOG4 check_wapp_levels: WAPP-1 power levels: 0.920 0.930 1.051 1.062 2009-Mar-14 22:19:33 LOG4 check_wapp_levels: WAPP-2 power levels: 1.030 0.976 1.114 0.908 2009-Mar-14 22:19:33 LOG4 check_wapp_levels: WAPP-3 power levels: 0.900 0.986 1.025 0.922 2009-Mar-14 22:19:33 LOG4 check_wapp_levels: WAPP-4 power levels: 0.942 0.110 1.036 0.119 2009-Mar-14 22:19:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:19:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:19:39 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:19:41 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.110 (still bad) 2009-Mar-14 22:19:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:19:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:19:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:19:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:19:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:19:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:19:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:19:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:19:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:20:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:20:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:20:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:20:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:20:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:20:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:20:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:20:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:20:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:20:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:20:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:20:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:20:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:20:27 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.108 (still bad) 2009-Mar-14 22:20:30 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.108 (still bad) 2009-Mar-14 22:20:32 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.109 (still bad) 2009-Mar-14 22:20:34 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:20:34 LOG4 check_wapp_levels: WAPP-1 power levels: 0.922 0.931 1.052 1.062 2009-Mar-14 22:20:34 LOG4 check_wapp_levels: WAPP-2 power levels: 1.030 0.977 1.108 0.904 2009-Mar-14 22:20:34 LOG4 check_wapp_levels: WAPP-3 power levels: 0.900 0.987 1.023 0.920 2009-Mar-14 22:20:34 LOG4 check_wapp_levels: WAPP-4 power levels: 0.938 0.109 1.034 0.119 2009-Mar-14 22:20:36 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.108 (still bad) 2009-Mar-14 22:20:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:20:40 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:20:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:20:44 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.109 (still bad) 2009-Mar-14 22:20:46 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.110 (still bad) 2009-Mar-14 22:20:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:20:50 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:20:52 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.110 (still bad) 2009-Mar-14 22:20:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:20:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:20:58 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:21:00 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.110 (still bad) 2009-Mar-14 22:21:02 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:21:04 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:21:06 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.110 (still bad) 2009-Mar-14 22:21:08 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:21:10 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:21:12 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:21:14 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:21:16 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:21:18 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:21:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:21:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:21:24 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:21:26 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:21:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:21:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:21:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:21:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:21:36 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:21:36 LOG4 check_wapp_levels: WAPP-1 power levels: 0.925 0.933 1.050 1.061 2009-Mar-14 22:21:36 LOG4 check_wapp_levels: WAPP-2 power levels: 1.029 0.975 1.120 0.912 2009-Mar-14 22:21:36 LOG4 check_wapp_levels: WAPP-3 power levels: 0.899 0.985 1.025 0.921 2009-Mar-14 22:21:36 LOG4 check_wapp_levels: WAPP-4 power levels: 0.938 0.109 1.033 0.119 2009-Mar-14 22:21:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.129 (still bad) 2009-Mar-14 22:21:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.127 (still bad) 2009-Mar-14 22:21:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.126 (still bad) 2009-Mar-14 22:21:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.125 (still bad) 2009-Mar-14 22:21:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.122 (still bad) 2009-Mar-14 22:21:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.119 (still bad) 2009-Mar-14 22:21:50 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.123 (still bad) 2009-Mar-14 22:21:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:21:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:21:57 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:21:59 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:22:01 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:22:03 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.119 (still bad) 2009-Mar-14 22:22:05 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:22:07 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:22:09 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:22:11 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.110 (still bad) 2009-Mar-14 22:22:13 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:22:15 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.119 (still bad) 2009-Mar-14 22:22:17 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:22:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:22:21 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:22:23 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:22:25 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:22:27 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.120 (still bad) 2009-Mar-14 22:22:29 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:22:31 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:22:33 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:22:35 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:22:37 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:22:37 LOG4 check_wapp_levels: WAPP-1 power levels: 0.926 0.933 1.053 1.062 2009-Mar-14 22:22:37 LOG4 check_wapp_levels: WAPP-2 power levels: 1.032 0.976 1.113 0.903 2009-Mar-14 22:22:37 LOG4 check_wapp_levels: WAPP-3 power levels: 0.901 0.989 1.031 0.924 2009-Mar-14 22:22:37 LOG4 check_wapp_levels: WAPP-4 power levels: 0.940 0.110 1.036 0.119 2009-Mar-14 22:22:39 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:22:41 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:22:43 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:22:45 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:22:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:22:49 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:22:51 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:22:53 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:22:55 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:22:57 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:22:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:23:01 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:23:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:23:05 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:23:07 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:23:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:23:11 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:23:12 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 22:23:12 STOP end_task: Finishing task 'waiting on WAPP spectra' with status 'OK' 2009-Mar-14 22:23:12 LOG5 end_task: Level: (3) ID = <10134> Status = 0 0 0 0 ok 2009-Mar-14 22:23:12 STOP end_task: Finishing task 'WAPP spectral observation' with status 'OK' 2009-Mar-14 22:23:12 LOG5 end_task: Level: (2) ID = <10133> Status = 0 0 0 0 ok 2009-Mar-14 22:23:12 LOG1 fixed_driftmap: New position: year = 2009.2024169138338 RA = 09:26:57.3 RA/Dec = 09:27:30.8 +21:51:30.7 2009-Mar-14 22:23:12 NOTE fixed_driftmap: Correcting ZA to 3:30:17.0 ... 2009-Mar-14 22:23:12 LOG3 vw_send: To DATATAKING: pnt tr -UD 180.0 3.5047137177 -CF 2009-Mar-14 22:23:12 LOG2 take_cal: Calling 'take_cal hcorcal 1 1' 2009-Mar-14 22:23:12 START begin_task: Starting task 'WAPP calibration' 2009-Mar-14 22:23:12 LOG5 begin_task: Level: (2) ID = <10135> Status = 0 0 0 0 ok 2009-Mar-14 22:23:12 LOG4 send_obs_status: To obs_status: <0> NEWTASK {WAPP Calibration} INFO {Making WAPP calibration ...} 2009-Mar-14 22:23:12 START begin_task: Starting task 'selecting calibration type' 2009-Mar-14 22:23:12 LOG5 begin_task: Level: (3) ID = <10136> Status = 0 0 0 0 ok 2009-Mar-14 22:23:12 LOG3 vw_send: To DATATAKING: setcal hcorcal 2009-Mar-14 22:23:12 LOG2 socket_wait: Starting sockwait on DATATAKING for 'setcal' using string 'DONE' 2009-Mar-14 22:23:12 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:23:12 START begin_task: Starting task 'waiting on setcal' 2009-Mar-14 22:23:12 LOG5 begin_task: Level: (4) ID = <10137> Status = 0 0 0 0 ok 2009-Mar-14 22:23:12 LOG4 got_cormsg: From DATATAKING: pnt tr -UD 180.0 3.5047137177 -CF 2009-Mar-14 22:23:12 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:23:12 LOG4 got_cormsg: From DATATAKING: setcal hcorcal 2009-Mar-14 22:23:12 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:23:13 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:23:13 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 22:23:13 STOP end_task: Finishing task 'waiting on setcal' with status 'OK' 2009-Mar-14 22:23:13 LOG5 end_task: Level: (4) ID = <10137> Status = 0 0 0 0 ok 2009-Mar-14 22:23:13 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'setcal' 2009-Mar-14 22:23:13 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:23:13 LOG3 socket_wait: To ALFAMON: CAL HI 2009-Mar-14 22:23:13 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:23:13 LOG5 begin_task: Level: (4) ID = <10138> Status = 0 0 0 0 ok 2009-Mar-14 22:23:13 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:23:13 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:23:13 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:23:13 LOG5 end_task: Level: (4) ID = <10138> Status = 0 0 0 0 ok 2009-Mar-14 22:23:13 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:23:13 LOG3 to_alfamon: To ALFAMON: CAL HI 2009-Mar-14 22:23:13 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:23:13 LOG3 socket_wait: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:23:13 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:23:13 LOG5 begin_task: Level: (4) ID = <10139> Status = 0 0 0 0 ok 2009-Mar-14 22:23:13 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:23:13 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:23:13 LOG5 end_task: Level: (4) ID = <10139> Status = 0 0 0 0 ok 2009-Mar-14 22:23:13 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:23:13 LOG3 to_alfamon: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:23:13 STOP end_task: Finishing task 'selecting calibration type' with status 'OK' 2009-Mar-14 22:23:13 LOG5 end_task: Level: (3) ID = <10136> Status = 0 0 0 0 ok 2009-Mar-14 22:23:13 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_cal_on MESSAGE {Setting CAL-ON ...} 2009-Mar-14 22:23:13 LOG3 wapp_calcontrol: To CALCONTROL: CALON 2009-Mar-14 22:23:13 LOG3 sock_errsend: To CALCONTROL: CALON STATUS 2009-Mar-14 22:23:13 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 22:23:13 LOG5 begin_task: Level: (3) ID = <10140> Status = 0 0 0 0 ok 2009-Mar-14 22:23:13 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 22:23:13 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x03 2009-Mar-14 22:23:13 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 22:23:13 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 22:23:13 LOG5 end_task: Level: (3) ID = <10140> Status = 0 0 0 0 ok 2009-Mar-14 22:23:13 LOG4 take_data: Calling 'take_data 1 1 CAL ON stat_cal_on {CAL-ON spectra}' 2009-Mar-14 22:23:13 START begin_task: Starting task 'WAPP spectral observation' 2009-Mar-14 22:23:13 LOG5 begin_task: Level: (3) ID = <10141> Status = 0 0 0 0 ok 2009-Mar-14 22:23:13 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON spectra ...} 2009-Mar-14 22:23:13 LOG5 log_alfabeam: Can't log alfabeam, not J2000 2009-Mar-14 22:23:13 INFO2 take_data: Starting WAPP 1-second scan: 907300176 2009-Mar-14 22:23:14 START begin_task: Starting task 'waiting on WAPP spectra' 2009-Mar-14 22:23:14 LOG5 begin_task: Level: (4) ID = <10142> Status = 0 0 0 0 ok 2009-Mar-14 22:23:14 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 22:23:14 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:23:14 LOG4 send_obs_status: To obs_status: <0> TASKTIME 1 BITMAP stat_cal_on MESSAGE {Taking CAL-ON spectra ...} 2009-Mar-14 22:23:14 INFO1 WAPP=1+2+3+4-start_spectra: start sec 8595.00 2009-Mar-14 22:23:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.000000 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 22:23:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:23:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:23:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 22:23:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 22:23:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:23:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:23:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:23:16 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:23:16 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.559 (still bad) 2009-Mar-14 22:23:16 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 22:23:16 STOP end_task: Finishing task 'waiting on WAPP spectra' with status 'OK' 2009-Mar-14 22:23:16 LOG5 end_task: Level: (4) ID = <10142> Status = 0 0 0 0 ok 2009-Mar-14 22:23:16 STOP end_task: Finishing task 'WAPP spectral observation' with status 'OK' 2009-Mar-14 22:23:16 LOG5 end_task: Level: (3) ID = <10141> Status = 0 0 0 0 ok 2009-Mar-14 22:23:16 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_cal_off MESSAGE {Setting CAL-OFF ...} 2009-Mar-14 22:23:16 LOG3 wapp_calcontrol: To CALCONTROL: CALOFF 2009-Mar-14 22:23:16 LOG3 sock_errsend: To CALCONTROL: CALOFF STATUS 2009-Mar-14 22:23:16 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 22:23:16 LOG5 begin_task: Level: (3) ID = <10143> Status = 0 0 0 0 ok 2009-Mar-14 22:23:16 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 22:23:16 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 22:23:16 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 22:23:16 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 22:23:16 LOG5 end_task: Level: (3) ID = <10143> Status = 0 0 0 0 ok 2009-Mar-14 22:23:16 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_busy 2009-Mar-14 22:23:16 STOP finish_task: Finishing task 'WAPP calibration' 2009-Mar-14 22:23:16 LOG5 finish_task: Level: (2) ID = <10135> Status = 0 0 0 0 ok 2009-Mar-14 22:23:16 INFO2 finish_task: DONE finished calibration: WAPP calibration 2009-Mar-14 22:23:16 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 22:23:16 STOP end_task: Finishing task 'WAPP calibration' with status 'OK' 2009-Mar-14 22:23:16 LOG5 end_task: Level: (2) ID = <10135> Status = 0 0 0 0 ok 2009-Mar-14 22:23:16 INFO2 fixed_driftmap: Starting fixed azimuth drift map loop 3 of 99 2009-Mar-14 22:23:17 LOG4 send_obs_status: To obs_status: <1> LOOP 3 2009-Mar-14 22:23:17 LOG3 send_to_one_wapp: To WAPPCON: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:23:17 LOG3 send_to_one_wapp: To WAPPCON2: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:23:17 LOG3 send_to_one_wapp: To WAPPCON3: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:23:17 LOG3 send_to_one_wapp: To WAPPCON4: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:23:17 LOG4 send_obs_status: To obs_status: <1> INFO {Making drift scan followed by CAL} 2009-Mar-14 22:23:17 LOG4 take_data: Calling 'take_data 600 1 FIXEDAZ FIXEDAZ stat_drift {drift scan}' 2009-Mar-14 22:23:17 START begin_task: Starting task 'WAPP spectral observation' 2009-Mar-14 22:23:17 LOG5 begin_task: Level: (2) ID = <10144> Status = 0 0 0 0 ok 2009-Mar-14 22:23:17 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for drift scan ...} 2009-Mar-14 22:23:17 LOG5 log_alfabeam: Can't log alfabeam, not J2000 2009-Mar-14 22:23:17 INFO2 take_data: Starting WAPP 600-second scan: 907300177 2009-Mar-14 22:23:17 START begin_task: Starting task 'waiting on WAPP spectra' 2009-Mar-14 22:23:17 LOG5 begin_task: Level: (3) ID = <10145> Status = 0 0 0 0 ok 2009-Mar-14 22:23:17 LOG4 WAPP=1+2+3+4-wappcon: Received command 'PROJECT a2010 Lyle Hoffman' 2009-Mar-14 22:23:17 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 22:23:17 LOG4 send_obs_status: To obs_status: <0> TASKTIME 600 BITMAP stat_drift MESSAGE {Taking drift scan ...} 2009-Mar-14 22:23:17 INFO1 WAPP=1+2+3+4-start_spectra: start sec 8598.00 2009-Mar-14 22:23:17 NOTE WAPPDATA-new_file: New FITS file: wapp.20090314.a2010.0032.fits 2009-Mar-14 22:23:17 LOG4 send_obs_status: To obs_status: <0> FILENAME {wapp.20090314.a2010.0032.fits} 2009-Mar-14 22:23:18 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.559 (still bad) 2009-Mar-14 22:23:19 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.000000 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 22:23:19 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:23:19 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:23:19 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 22:23:19 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 22:23:19 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:23:19 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:23:19 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:23:19 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:23:19 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 14 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:23:20 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:23:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:23:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:23:26 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:23:28 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:23:30 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:23:32 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:23:34 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:23:36 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:23:38 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:23:38 LOG4 check_wapp_levels: WAPP-1 power levels: 0.929 0.939 1.057 1.070 2009-Mar-14 22:23:38 LOG4 check_wapp_levels: WAPP-2 power levels: 1.036 0.979 1.117 0.906 2009-Mar-14 22:23:38 LOG4 check_wapp_levels: WAPP-3 power levels: 0.902 0.990 1.033 0.926 2009-Mar-14 22:23:38 LOG4 check_wapp_levels: WAPP-4 power levels: 0.943 0.110 1.040 0.119 2009-Mar-14 22:23:40 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:23:42 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:23:44 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:23:46 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:23:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:23:50 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.118 (still bad) 2009-Mar-14 22:23:52 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:23:54 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:23:56 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:23:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:24:00 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:24:02 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.119 (still bad) 2009-Mar-14 22:24:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:24:06 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:24:08 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:24:10 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:24:12 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:24:14 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:24:16 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:24:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:24:20 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:24:22 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:24:25 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:24:27 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:24:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:24:31 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:24:33 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:24:35 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:24:37 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:24:39 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:24:39 LOG4 check_wapp_levels: WAPP-1 power levels: 0.928 0.940 1.055 1.069 2009-Mar-14 22:24:39 LOG4 check_wapp_levels: WAPP-2 power levels: 1.034 0.979 1.117 0.901 2009-Mar-14 22:24:39 LOG4 check_wapp_levels: WAPP-3 power levels: 0.899 0.987 1.031 0.924 2009-Mar-14 22:24:39 LOG4 check_wapp_levels: WAPP-4 power levels: 0.946 0.110 1.044 0.119 2009-Mar-14 22:24:41 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:24:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:24:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:24:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:24:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:24:51 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:24:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:24:55 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:24:57 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:24:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:25:01 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:25:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:25:05 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:25:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:25:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:25:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:25:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:25:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:25:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:25:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:25:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:25:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:25:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:41 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:25:41 LOG4 check_wapp_levels: WAPP-1 power levels: 0.924 0.936 1.048 1.061 2009-Mar-14 22:25:41 LOG4 check_wapp_levels: WAPP-2 power levels: 1.028 0.970 1.112 0.901 2009-Mar-14 22:25:41 LOG4 check_wapp_levels: WAPP-3 power levels: 0.894 0.984 1.026 0.920 2009-Mar-14 22:25:41 LOG4 check_wapp_levels: WAPP-4 power levels: 0.940 0.109 1.038 0.119 2009-Mar-14 22:25:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:25:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:25:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:25:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:25:56 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:25:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:26:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:26:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:26:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:26:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:26:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:26:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:26:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:26:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:26:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:26:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:26:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:26:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:26:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:26:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.119 (still bad) 2009-Mar-14 22:26:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:26:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:26:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:26:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:26:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:26:38 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.118 (still bad) 2009-Mar-14 22:26:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:26:42 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:26:42 LOG4 check_wapp_levels: WAPP-1 power levels: 0.938 0.949 1.053 1.064 2009-Mar-14 22:26:42 LOG4 check_wapp_levels: WAPP-2 power levels: 1.030 0.975 1.114 0.895 2009-Mar-14 22:26:42 LOG4 check_wapp_levels: WAPP-3 power levels: 0.897 0.988 1.028 0.921 2009-Mar-14 22:26:42 LOG4 check_wapp_levels: WAPP-4 power levels: 0.939 0.109 1.037 0.119 2009-Mar-14 22:26:44 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:26:46 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:26:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:26:50 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:26:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:26:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:26:56 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:26:57 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 8 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:26:58 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:27:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:27:02 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.118 (still bad) 2009-Mar-14 22:27:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:27:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:27:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:27:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:27:12 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:27:14 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.119 (still bad) 2009-Mar-14 22:27:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:27:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:27:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:27:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:27:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:27:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.120 (still bad) 2009-Mar-14 22:27:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:27:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:27:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:27:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:27:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:27:39 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:27:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:27:43 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:27:43 LOG4 check_wapp_levels: WAPP-1 power levels: 0.919 0.929 1.050 1.058 2009-Mar-14 22:27:43 LOG4 check_wapp_levels: WAPP-2 power levels: 1.027 0.972 1.111 0.899 2009-Mar-14 22:27:43 LOG4 check_wapp_levels: WAPP-3 power levels: 0.899 0.986 1.027 0.917 2009-Mar-14 22:27:43 LOG4 check_wapp_levels: WAPP-4 power levels: 0.937 0.109 1.034 0.119 2009-Mar-14 22:27:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:27:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:27:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:27:50 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:27:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.117 (still bad) 2009-Mar-14 22:27:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:27:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:27:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:27:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:28:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:28:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.119 (still bad) 2009-Mar-14 22:28:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:28:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:28:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.118 (still bad) 2009-Mar-14 22:28:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.118 (still bad) 2009-Mar-14 22:28:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:28:15 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:28:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:28:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.117 (still bad) 2009-Mar-14 22:28:21 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:28:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.124 (still bad) 2009-Mar-14 22:28:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.131 (still bad) 2009-Mar-14 22:28:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.139 (still bad) 2009-Mar-14 22:28:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.145 (still bad) 2009-Mar-14 22:28:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.149 (still bad) 2009-Mar-14 22:28:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.149 (still bad) 2009-Mar-14 22:28:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.147 (still bad) 2009-Mar-14 22:28:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.138 (still bad) 2009-Mar-14 22:28:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.132 (still bad) 2009-Mar-14 22:28:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.124 (still bad) 2009-Mar-14 22:28:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.119 (still bad) 2009-Mar-14 22:28:44 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:28:44 LOG4 check_wapp_levels: WAPP-1 power levels: 0.919 0.930 1.050 1.061 2009-Mar-14 22:28:44 LOG4 check_wapp_levels: WAPP-2 power levels: 1.030 0.976 1.115 0.900 2009-Mar-14 22:28:44 LOG4 check_wapp_levels: WAPP-3 power levels: 0.903 0.994 1.023 0.916 2009-Mar-14 22:28:44 LOG4 check_wapp_levels: WAPP-4 power levels: 0.937 0.109 1.033 0.118 2009-Mar-14 22:28:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:28:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:28:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:28:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:28:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:28:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:28:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:29:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:29:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:29:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.118 (still bad) 2009-Mar-14 22:29:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.118 (still bad) 2009-Mar-14 22:29:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.122 (still bad) 2009-Mar-14 22:29:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.126 (still bad) 2009-Mar-14 22:29:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.129 (still bad) 2009-Mar-14 22:29:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.126 (still bad) 2009-Mar-14 22:29:15 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 11 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:29:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.129 (still bad) 2009-Mar-14 22:29:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.124 (still bad) 2009-Mar-14 22:29:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.122 (still bad) 2009-Mar-14 22:29:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.119 (still bad) 2009-Mar-14 22:29:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:29:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:29:28 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:29:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:29:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:29:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:29:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:29:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:29:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:29:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:29:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:29:46 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:29:46 LOG4 check_wapp_levels: WAPP-1 power levels: 0.920 0.929 1.047 1.059 2009-Mar-14 22:29:46 LOG4 check_wapp_levels: WAPP-2 power levels: 1.027 0.972 1.112 0.896 2009-Mar-14 22:29:46 LOG4 check_wapp_levels: WAPP-3 power levels: 0.900 0.986 1.056 0.946 2009-Mar-14 22:29:46 LOG4 check_wapp_levels: WAPP-4 power levels: 0.937 0.109 1.032 0.118 2009-Mar-14 22:29:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:29:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:29:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:29:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:29:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:29:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:30:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:30:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:30:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:30:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:30:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:30:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:30:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:30:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:30:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:30:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:30:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:30:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:30:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:30:27 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:30:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:30:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:30:33 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.109 (still bad) 2009-Mar-14 22:30:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:30:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:30:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:30:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:30:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:30:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:30:47 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:30:47 LOG4 check_wapp_levels: WAPP-1 power levels: 0.920 0.931 1.051 1.058 2009-Mar-14 22:30:47 LOG4 check_wapp_levels: WAPP-2 power levels: 1.028 0.973 1.109 0.894 2009-Mar-14 22:30:47 LOG4 check_wapp_levels: WAPP-3 power levels: 0.899 0.987 1.023 0.915 2009-Mar-14 22:30:47 LOG4 check_wapp_levels: WAPP-4 power levels: 0.936 0.109 1.032 0.119 2009-Mar-14 22:30:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:30:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:30:53 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.109 (still bad) 2009-Mar-14 22:30:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:30:57 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:30:59 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.110 (still bad) 2009-Mar-14 22:31:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:31:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:31:05 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:31:07 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:31:09 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:31:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:31:13 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:31:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:31:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:31:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:31:21 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:31:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:31:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:31:27 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:31:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:31:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:31:34 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:31:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:31:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:31:40 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:31:42 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:31:44 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:31:46 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:31:48 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:31:48 LOG4 check_wapp_levels: WAPP-1 power levels: 0.923 0.929 1.046 1.061 2009-Mar-14 22:31:48 LOG4 check_wapp_levels: WAPP-2 power levels: 1.028 0.974 1.110 0.890 2009-Mar-14 22:31:48 LOG4 check_wapp_levels: WAPP-3 power levels: 0.900 0.989 1.024 0.919 2009-Mar-14 22:31:48 LOG4 check_wapp_levels: WAPP-4 power levels: 0.938 0.109 1.034 0.119 2009-Mar-14 22:31:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:31:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:31:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:31:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:31:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:32:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:32:04 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:32:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:32:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:32:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:32:18 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.109 (still bad) 2009-Mar-14 22:32:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:32:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:32:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:32:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:32:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:38 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:32:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:32:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:32:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:32:48 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.109 (still bad) 2009-Mar-14 22:32:50 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:32:50 LOG4 check_wapp_levels: WAPP-1 power levels: 0.924 0.931 1.048 1.060 2009-Mar-14 22:32:50 LOG4 check_wapp_levels: WAPP-2 power levels: 1.027 0.972 1.110 0.896 2009-Mar-14 22:32:50 LOG4 check_wapp_levels: WAPP-3 power levels: 0.899 0.988 1.025 0.919 2009-Mar-14 22:32:50 LOG4 check_wapp_levels: WAPP-4 power levels: 0.940 0.110 1.037 0.119 2009-Mar-14 22:32:52 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:32:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:32:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:32:58 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:33:01 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:33:03 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:33:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:33:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:33:09 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:33:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:33:13 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:33:15 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.120 (still bad) 2009-Mar-14 22:33:17 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:33:18 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 22:33:18 STOP end_task: Finishing task 'waiting on WAPP spectra' with status 'OK' 2009-Mar-14 22:33:18 LOG5 end_task: Level: (3) ID = <10145> Status = 0 0 0 0 ok 2009-Mar-14 22:33:18 STOP end_task: Finishing task 'WAPP spectral observation' with status 'OK' 2009-Mar-14 22:33:18 LOG5 end_task: Level: (2) ID = <10144> Status = 0 0 0 0 ok 2009-Mar-14 22:33:18 LOG1 fixed_driftmap: New position: year = 2009.2024361168151 RA = 09:37:05.1 RA/Dec = 09:37:38.5 +21:51:25.1 2009-Mar-14 22:33:18 NOTE fixed_driftmap: Correcting ZA to 3:30:11.4 ... 2009-Mar-14 22:33:18 LOG3 vw_send: To DATATAKING: pnt tr -UD 180.0 3.5031788545 -CF 2009-Mar-14 22:33:18 LOG2 take_cal: Calling 'take_cal hcorcal 1 1' 2009-Mar-14 22:33:18 START begin_task: Starting task 'WAPP calibration' 2009-Mar-14 22:33:18 LOG5 begin_task: Level: (2) ID = <10146> Status = 0 0 0 0 ok 2009-Mar-14 22:33:18 LOG4 send_obs_status: To obs_status: <0> NEWTASK {WAPP Calibration} INFO {Making WAPP calibration ...} 2009-Mar-14 22:33:18 START begin_task: Starting task 'selecting calibration type' 2009-Mar-14 22:33:18 LOG5 begin_task: Level: (3) ID = <10147> Status = 0 0 0 0 ok 2009-Mar-14 22:33:18 LOG3 vw_send: To DATATAKING: setcal hcorcal 2009-Mar-14 22:33:18 LOG2 socket_wait: Starting sockwait on DATATAKING for 'setcal' using string 'DONE' 2009-Mar-14 22:33:18 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:33:18 START begin_task: Starting task 'waiting on setcal' 2009-Mar-14 22:33:18 LOG5 begin_task: Level: (4) ID = <10148> Status = 0 0 0 0 ok 2009-Mar-14 22:33:18 LOG4 got_cormsg: From DATATAKING: pnt tr -UD 180.0 3.5031788545 -CF 2009-Mar-14 22:33:18 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:33:18 LOG4 got_cormsg: From DATATAKING: setcal hcorcal 2009-Mar-14 22:33:18 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:33:19 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:33:19 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 22:33:19 STOP end_task: Finishing task 'waiting on setcal' with status 'OK' 2009-Mar-14 22:33:19 LOG5 end_task: Level: (4) ID = <10148> Status = 0 0 0 0 ok 2009-Mar-14 22:33:19 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'setcal' 2009-Mar-14 22:33:19 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:33:19 LOG3 socket_wait: To ALFAMON: CAL HI 2009-Mar-14 22:33:19 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:33:19 LOG5 begin_task: Level: (4) ID = <10149> Status = 0 0 0 0 ok 2009-Mar-14 22:33:19 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:33:19 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:33:19 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:33:19 LOG5 end_task: Level: (4) ID = <10149> Status = 0 0 0 0 ok 2009-Mar-14 22:33:19 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:33:19 LOG3 to_alfamon: To ALFAMON: CAL HI 2009-Mar-14 22:33:19 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:33:19 LOG3 socket_wait: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:33:19 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:33:19 LOG5 begin_task: Level: (4) ID = <10150> Status = 0 0 0 0 ok 2009-Mar-14 22:33:19 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:33:19 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:33:19 LOG5 end_task: Level: (4) ID = <10150> Status = 0 0 0 0 ok 2009-Mar-14 22:33:19 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:33:19 LOG3 to_alfamon: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:33:19 STOP end_task: Finishing task 'selecting calibration type' with status 'OK' 2009-Mar-14 22:33:19 LOG5 end_task: Level: (3) ID = <10147> Status = 0 0 0 0 ok 2009-Mar-14 22:33:19 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_cal_on MESSAGE {Setting CAL-ON ...} 2009-Mar-14 22:33:19 LOG3 wapp_calcontrol: To CALCONTROL: CALON 2009-Mar-14 22:33:19 LOG3 sock_errsend: To CALCONTROL: CALON STATUS 2009-Mar-14 22:33:19 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 22:33:19 LOG5 begin_task: Level: (3) ID = <10151> Status = 0 0 0 0 ok 2009-Mar-14 22:33:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:33:19 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 22:33:19 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x03 2009-Mar-14 22:33:19 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 22:33:19 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 22:33:19 LOG5 end_task: Level: (3) ID = <10151> Status = 0 0 0 0 ok 2009-Mar-14 22:33:19 LOG4 take_data: Calling 'take_data 1 1 CAL ON stat_cal_on {CAL-ON spectra}' 2009-Mar-14 22:33:19 START begin_task: Starting task 'WAPP spectral observation' 2009-Mar-14 22:33:19 LOG5 begin_task: Level: (3) ID = <10152> Status = 0 0 0 0 ok 2009-Mar-14 22:33:19 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON spectra ...} 2009-Mar-14 22:33:19 LOG5 log_alfabeam: Can't log alfabeam, not J2000 2009-Mar-14 22:33:19 INFO2 take_data: Starting WAPP 1-second scan: 907300178 2009-Mar-14 22:33:19 START begin_task: Starting task 'waiting on WAPP spectra' 2009-Mar-14 22:33:19 LOG5 begin_task: Level: (4) ID = <10153> Status = 0 0 0 0 ok 2009-Mar-14 22:33:19 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 22:33:19 LOG4 send_obs_status: To obs_status: <0> TASKTIME 1 BITMAP stat_cal_on MESSAGE {Taking CAL-ON spectra ...} 2009-Mar-14 22:33:20 INFO1 WAPP=1+2+3+4-start_spectra: start sec 9200.00 2009-Mar-14 22:33:21 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.000000 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 22:33:21 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:33:21 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:33:21 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 22:33:21 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 22:33:21 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:33:21 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:33:21 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:33:21 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:33:21 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 22:33:21 STOP end_task: Finishing task 'waiting on WAPP spectra' with status 'OK' 2009-Mar-14 22:33:21 LOG5 end_task: Level: (4) ID = <10153> Status = 0 0 0 0 ok 2009-Mar-14 22:33:21 STOP end_task: Finishing task 'WAPP spectral observation' with status 'OK' 2009-Mar-14 22:33:21 LOG5 end_task: Level: (3) ID = <10152> Status = 0 0 0 0 ok 2009-Mar-14 22:33:21 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_cal_off MESSAGE {Setting CAL-OFF ...} 2009-Mar-14 22:33:21 LOG3 wapp_calcontrol: To CALCONTROL: CALOFF 2009-Mar-14 22:33:21 LOG3 sock_errsend: To CALCONTROL: CALOFF STATUS 2009-Mar-14 22:33:21 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 22:33:21 LOG5 begin_task: Level: (3) ID = <10154> Status = 0 0 0 0 ok 2009-Mar-14 22:33:21 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 22:33:21 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 22:33:21 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 22:33:21 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 22:33:21 LOG5 end_task: Level: (3) ID = <10154> Status = 0 0 0 0 ok 2009-Mar-14 22:33:21 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_busy 2009-Mar-14 22:33:21 STOP finish_task: Finishing task 'WAPP calibration' 2009-Mar-14 22:33:21 LOG5 finish_task: Level: (2) ID = <10146> Status = 0 0 0 0 ok 2009-Mar-14 22:33:21 INFO2 finish_task: DONE finished calibration: WAPP calibration 2009-Mar-14 22:33:21 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 22:33:22 STOP end_task: Finishing task 'WAPP calibration' with status 'OK' 2009-Mar-14 22:33:22 LOG5 end_task: Level: (2) ID = <10146> Status = 0 0 0 0 ok 2009-Mar-14 22:33:22 INFO2 fixed_driftmap: Starting fixed azimuth drift map loop 4 of 99 2009-Mar-14 22:33:22 LOG4 send_obs_status: To obs_status: <1> LOOP 4 2009-Mar-14 22:33:22 LOG3 send_to_one_wapp: To WAPPCON: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:33:22 LOG3 send_to_one_wapp: To WAPPCON2: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:33:22 LOG3 send_to_one_wapp: To WAPPCON3: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:33:22 LOG3 send_to_one_wapp: To WAPPCON4: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:33:22 LOG4 send_obs_status: To obs_status: <1> INFO {Making drift scan followed by CAL} 2009-Mar-14 22:33:22 LOG4 take_data: Calling 'take_data 600 1 FIXEDAZ FIXEDAZ stat_drift {drift scan}' 2009-Mar-14 22:33:22 START begin_task: Starting task 'WAPP spectral observation' 2009-Mar-14 22:33:22 LOG5 begin_task: Level: (2) ID = <10155> Status = 0 0 0 0 ok 2009-Mar-14 22:33:22 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for drift scan ...} 2009-Mar-14 22:33:22 LOG5 log_alfabeam: Can't log alfabeam, not J2000 2009-Mar-14 22:33:22 INFO2 take_data: Starting WAPP 600-second scan: 907300179 2009-Mar-14 22:33:22 START begin_task: Starting task 'waiting on WAPP spectra' 2009-Mar-14 22:33:22 LOG5 begin_task: Level: (3) ID = <10156> Status = 0 0 0 0 ok 2009-Mar-14 22:33:22 LOG4 WAPP=1+2+3+4-wappcon: Received command 'PROJECT a2010 Lyle Hoffman' 2009-Mar-14 22:33:22 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 22:33:22 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.561 (still bad) 2009-Mar-14 22:33:22 LOG4 send_obs_status: To obs_status: <0> TASKTIME 600 BITMAP stat_drift MESSAGE {Taking drift scan ...} 2009-Mar-14 22:33:22 INFO1 WAPP=1+2+3+4-start_spectra: start sec 9203.00 2009-Mar-14 22:33:22 NOTE WAPPDATA-new_file: New FITS file: wapp.20090314.a2010.0033.fits 2009-Mar-14 22:33:22 LOG4 send_obs_status: To obs_status: <0> FILENAME {wapp.20090314.a2010.0033.fits} 2009-Mar-14 22:33:24 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.000000 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 22:33:24 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:33:24 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:33:24 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 22:33:24 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 22:33:24 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:33:24 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:33:24 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:33:24 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:33:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:33:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:33:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:33:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:33:32 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:33:34 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:33:36 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.118 (still bad) 2009-Mar-14 22:33:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.117 (still bad) 2009-Mar-14 22:33:40 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.118 (still bad) 2009-Mar-14 22:33:42 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:33:44 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:33:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:33:48 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:33:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.125 (still bad) 2009-Mar-14 22:33:52 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:33:52 LOG4 check_wapp_levels: WAPP-1 power levels: 0.926 0.935 1.048 1.060 2009-Mar-14 22:33:52 LOG4 check_wapp_levels: WAPP-2 power levels: 1.029 0.972 1.137 0.915 2009-Mar-14 22:33:52 LOG4 check_wapp_levels: WAPP-3 power levels: 0.897 0.984 1.024 0.919 2009-Mar-14 22:33:52 LOG4 check_wapp_levels: WAPP-4 power levels: 0.937 0.109 1.035 0.119 2009-Mar-14 22:33:54 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.152 (still bad) 2009-Mar-14 22:33:56 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.163 (still bad) 2009-Mar-14 22:33:58 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.170 (still bad) 2009-Mar-14 22:34:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.173 (still bad) 2009-Mar-14 22:34:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.168 (still bad) 2009-Mar-14 22:34:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.159 (still bad) 2009-Mar-14 22:34:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.147 (still bad) 2009-Mar-14 22:34:08 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.134 (still bad) 2009-Mar-14 22:34:10 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.123 (still bad) 2009-Mar-14 22:34:12 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:34:14 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:34:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:34:18 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:34:21 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.110 (still bad) 2009-Mar-14 22:34:23 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:34:25 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:34:27 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:34:29 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:34:31 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:34:33 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:34:35 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:34:37 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:34:39 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:34:41 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:34:43 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:34:45 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:34:47 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:34:49 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:34:51 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:34:53 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:34:53 LOG4 check_wapp_levels: WAPP-1 power levels: 0.927 0.936 1.049 1.061 2009-Mar-14 22:34:53 LOG4 check_wapp_levels: WAPP-2 power levels: 1.030 0.973 1.114 0.897 2009-Mar-14 22:34:53 LOG4 check_wapp_levels: WAPP-3 power levels: 0.896 0.983 1.032 0.925 2009-Mar-14 22:34:53 LOG4 check_wapp_levels: WAPP-4 power levels: 0.937 0.110 1.034 0.119 2009-Mar-14 22:34:55 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:34:57 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:34:59 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:35:01 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:35:03 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.118 (still bad) 2009-Mar-14 22:35:05 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:35:07 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:35:09 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:35:11 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:35:13 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:35:15 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:35:17 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:35:19 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:35:21 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:35:23 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:35:25 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:35:27 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:35:29 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:35:31 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:35:33 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:35:35 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:35:37 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:35:39 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:35:41 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:35:43 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:35:45 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:35:48 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:35:50 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:35:52 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:35:54 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:35:54 LOG4 check_wapp_levels: WAPP-1 power levels: 0.926 0.934 1.048 1.063 2009-Mar-14 22:35:54 LOG4 check_wapp_levels: WAPP-2 power levels: 1.025 0.973 1.112 0.896 2009-Mar-14 22:35:54 LOG4 check_wapp_levels: WAPP-3 power levels: 0.896 0.984 1.029 0.924 2009-Mar-14 22:35:54 LOG4 check_wapp_levels: WAPP-4 power levels: 0.939 0.110 1.037 0.119 2009-Mar-14 22:35:56 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:35:58 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:36:00 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:36:02 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:36:04 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.121 (still bad) 2009-Mar-14 22:36:06 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.119 (still bad) 2009-Mar-14 22:36:08 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.120 (still bad) 2009-Mar-14 22:36:10 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.119 (still bad) 2009-Mar-14 22:36:12 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:36:14 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:36:16 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.120 (still bad) 2009-Mar-14 22:36:18 LOG4 exec_msg: From SCRAMWAPPDATA: log_message INFO4 WAPPDATA-queue_agcdata {Received duplicate AGC-datablock at 22:36:18.301 (seconds: 81378.301)!} 2009-Mar-14 22:36:18 INFO4 WAPPDATA-queue_agcdata: Received duplicate AGC-datablock at 22:36:18.301 (seconds: 81378.301)! 2009-Mar-14 22:36:18 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:36:19 INFO4 WAPPDATA-search_agc: Extrapolating agc-data from 81377.0 to 81378.0! 2009-Mar-14 22:36:20 INFO4 WAPPDATA-search_agc: Interpolating agc-data over 2.00 second time gap (81377.0 - 81379.0)! 2009-Mar-14 22:36:20 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:36:22 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:36:24 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.122 (still bad) 2009-Mar-14 22:36:26 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.126 (still bad) 2009-Mar-14 22:36:28 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.128 (still bad) 2009-Mar-14 22:36:30 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.127 (still bad) 2009-Mar-14 22:36:32 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.125 (still bad) 2009-Mar-14 22:36:34 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.121 (still bad) 2009-Mar-14 22:36:36 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.118 (still bad) 2009-Mar-14 22:36:38 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:36:40 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:36:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:36:44 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:36:46 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:36:48 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:36:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:36:52 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:36:54 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:36:56 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:36:56 LOG4 check_wapp_levels: WAPP-1 power levels: 0.923 0.932 1.061 1.072 2009-Mar-14 22:36:56 LOG4 check_wapp_levels: WAPP-2 power levels: 1.028 0.974 1.111 0.895 2009-Mar-14 22:36:56 LOG4 check_wapp_levels: WAPP-3 power levels: 0.911 1.001 1.026 0.918 2009-Mar-14 22:36:56 LOG4 check_wapp_levels: WAPP-4 power levels: 0.936 0.110 1.034 0.119 2009-Mar-14 22:36:58 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:00 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:37:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:37:04 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:06 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:37:08 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:37:10 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:37:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:37:17 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:37:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:37:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:37:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:37:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:37:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:37:29 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:37:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:37:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:37:35 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:37:37 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:39 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:41 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:37:43 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:45 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:47 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:49 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:51 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:53 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.118 (still bad) 2009-Mar-14 22:37:55 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:37:57 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:37:57 LOG4 check_wapp_levels: WAPP-1 power levels: 0.931 0.939 1.067 1.082 2009-Mar-14 22:37:57 LOG4 check_wapp_levels: WAPP-2 power levels: 1.027 0.973 1.111 0.904 2009-Mar-14 22:37:57 LOG4 check_wapp_levels: WAPP-3 power levels: 0.898 0.986 1.024 0.920 2009-Mar-14 22:37:57 LOG4 check_wapp_levels: WAPP-4 power levels: 0.936 0.110 1.032 0.119 2009-Mar-14 22:37:59 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:38:01 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:38:03 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.122 (still bad) 2009-Mar-14 22:38:05 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.132 (still bad) 2009-Mar-14 22:38:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.124 (still bad) 2009-Mar-14 22:38:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:38:11 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:38:13 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:38:15 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:38:17 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:38:19 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:38:21 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:38:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:38:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:38:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:38:29 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:38:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:38:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:38:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:38:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:38:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:38:41 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:38:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:38:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:38:48 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:38:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:38:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:38:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:38:56 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:38:58 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:38:58 LOG4 check_wapp_levels: WAPP-1 power levels: 0.922 0.931 1.051 1.061 2009-Mar-14 22:38:58 LOG4 check_wapp_levels: WAPP-2 power levels: 1.029 0.972 1.113 0.906 2009-Mar-14 22:38:58 LOG4 check_wapp_levels: WAPP-3 power levels: 0.897 0.987 1.028 0.919 2009-Mar-14 22:38:58 LOG4 check_wapp_levels: WAPP-4 power levels: 0.937 0.109 1.034 0.119 2009-Mar-14 22:39:00 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:39:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:39:04 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:39:06 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:39:08 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:39:10 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:39:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:39:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:39:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:39:18 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:39:20 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:39:22 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:39:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:39:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:39:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:39:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:39:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:39:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:39:36 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:39:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:39:40 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:39:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:39:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:39:46 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:39:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:39:50 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:39:52 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:39:54 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:39:56 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:39:58 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:40:00 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:40:00 LOG4 check_wapp_levels: WAPP-1 power levels: 0.919 0.929 1.048 1.060 2009-Mar-14 22:40:00 LOG4 check_wapp_levels: WAPP-2 power levels: 1.026 0.972 1.110 0.900 2009-Mar-14 22:40:00 LOG4 check_wapp_levels: WAPP-3 power levels: 0.896 0.983 1.024 0.916 2009-Mar-14 22:40:00 LOG4 check_wapp_levels: WAPP-4 power levels: 0.934 0.110 1.031 0.119 2009-Mar-14 22:40:02 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:40:04 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:40:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:40:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:40:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:40:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:40:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:40:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:40:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:40:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:40:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:40:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:40:27 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.109 (still bad) 2009-Mar-14 22:40:29 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:40:31 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:40:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:40:35 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:40:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:40:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:40:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.117 (still bad) 2009-Mar-14 22:40:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:40:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:40:47 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:40:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:40:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:40:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.117 (still bad) 2009-Mar-14 22:40:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:40:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:40:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:41:01 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:41:01 LOG4 check_wapp_levels: WAPP-1 power levels: 0.918 0.925 1.048 1.060 2009-Mar-14 22:41:01 LOG4 check_wapp_levels: WAPP-2 power levels: 1.027 0.974 1.115 0.899 2009-Mar-14 22:41:01 LOG4 check_wapp_levels: WAPP-3 power levels: 0.896 0.982 1.023 0.916 2009-Mar-14 22:41:01 LOG4 check_wapp_levels: WAPP-4 power levels: 0.936 0.109 1.033 0.118 2009-Mar-14 22:41:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:41:05 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.122 (still bad) 2009-Mar-14 22:41:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.117 (still bad) 2009-Mar-14 22:41:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:41:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:41:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:41:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:41:17 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:41:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:41:21 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:41:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:41:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:41:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:41:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:41:32 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:41:34 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:41:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:41:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:41:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.117 (still bad) 2009-Mar-14 22:41:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:41:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:41:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:41:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:41:50 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:41:52 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:41:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:41:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:41:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:42:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:42:02 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:42:02 LOG4 check_wapp_levels: WAPP-1 power levels: 0.916 0.925 1.049 1.059 2009-Mar-14 22:42:02 LOG4 check_wapp_levels: WAPP-2 power levels: 1.024 0.973 1.111 0.892 2009-Mar-14 22:42:02 LOG4 check_wapp_levels: WAPP-3 power levels: 0.896 0.985 1.024 0.920 2009-Mar-14 22:42:02 LOG4 check_wapp_levels: WAPP-4 power levels: 0.938 0.109 1.035 0.119 2009-Mar-14 22:42:04 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:42:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:42:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:42:10 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:42:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:42:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:42:16 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:42:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:42:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:42:22 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:42:24 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:42:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:42:28 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:42:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:42:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:42:34 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:42:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:42:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:42:40 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:42:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:42:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:42:46 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.110 (still bad) 2009-Mar-14 22:42:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:42:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:42:52 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.115 (still bad) 2009-Mar-14 22:42:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:42:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:42:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:43:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:43:03 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:43:03 LOG4 check_wapp_levels: WAPP-1 power levels: 0.918 0.926 1.048 1.059 2009-Mar-14 22:43:03 LOG4 check_wapp_levels: WAPP-2 power levels: 1.028 0.974 1.113 0.893 2009-Mar-14 22:43:03 LOG4 check_wapp_levels: WAPP-3 power levels: 0.898 0.984 1.023 0.919 2009-Mar-14 22:43:03 LOG4 check_wapp_levels: WAPP-4 power levels: 0.936 0.109 1.032 0.119 2009-Mar-14 22:43:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:43:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:43:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:43:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:43:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:43:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:43:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:43:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:43:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:43:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:43:23 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 22:43:23 STOP end_task: Finishing task 'waiting on WAPP spectra' with status 'OK' 2009-Mar-14 22:43:23 LOG5 end_task: Level: (3) ID = <10156> Status = 0 0 0 0 ok 2009-Mar-14 22:43:23 STOP end_task: Finishing task 'WAPP spectral observation' with status 'OK' 2009-Mar-14 22:43:23 LOG5 end_task: Level: (2) ID = <10155> Status = 0 0 0 0 ok 2009-Mar-14 22:43:23 LOG1 fixed_driftmap: New position: year = 2009.2024552881082 RA = 09:47:11.9 RA/Dec = 09:47:45.2 +21:51:19.9 2009-Mar-14 22:43:23 NOTE fixed_driftmap: Correcting ZA to 3:30:06.2 ... 2009-Mar-14 22:43:23 LOG3 vw_send: To DATATAKING: pnt tr -UD 180.0 3.5017262423 -CF 2009-Mar-14 22:43:23 LOG2 take_cal: Calling 'take_cal hcorcal 1 1' 2009-Mar-14 22:43:23 START begin_task: Starting task 'WAPP calibration' 2009-Mar-14 22:43:23 LOG5 begin_task: Level: (2) ID = <10157> Status = 0 0 0 0 ok 2009-Mar-14 22:43:23 LOG4 send_obs_status: To obs_status: <0> NEWTASK {WAPP Calibration} INFO {Making WAPP calibration ...} 2009-Mar-14 22:43:23 START begin_task: Starting task 'selecting calibration type' 2009-Mar-14 22:43:23 LOG5 begin_task: Level: (3) ID = <10158> Status = 0 0 0 0 ok 2009-Mar-14 22:43:23 LOG3 vw_send: To DATATAKING: setcal hcorcal 2009-Mar-14 22:43:23 LOG2 socket_wait: Starting sockwait on DATATAKING for 'setcal' using string 'DONE' 2009-Mar-14 22:43:23 LOG3 socket_wait: To DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:43:23 START begin_task: Starting task 'waiting on setcal' 2009-Mar-14 22:43:23 LOG5 begin_task: Level: (4) ID = <10159> Status = 0 0 0 0 ok 2009-Mar-14 22:43:23 LOG4 got_cormsg: From DATATAKING: pnt tr -UD 180.0 3.5017262423 -CF 2009-Mar-14 22:43:23 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:43:23 LOG4 got_cormsg: From DATATAKING: setcal hcorcal 2009-Mar-14 22:43:23 LOG4 got_cormsg: From DATATAKING: puts {DONE}; flush stdout 2009-Mar-14 22:43:23 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:43:23 LOG4 got_cormsg: From DATATAKING: DONE 2009-Mar-14 22:43:23 STOP end_task: Finishing task 'waiting on setcal' with status 'OK' 2009-Mar-14 22:43:23 LOG5 end_task: Level: (4) ID = <10159> Status = 0 0 0 0 ok 2009-Mar-14 22:43:23 LOG3 socket_wait: DONE with sockwait on DATATAKING for 'setcal' 2009-Mar-14 22:43:23 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:43:23 LOG3 socket_wait: To ALFAMON: CAL HI 2009-Mar-14 22:43:23 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:43:23 LOG5 begin_task: Level: (4) ID = <10160> Status = 0 0 0 0 ok 2009-Mar-14 22:43:24 LOG4 got_cormsg: From DATATAKING: vw% 2009-Mar-14 22:43:24 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:43:24 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:43:24 LOG5 end_task: Level: (4) ID = <10160> Status = 0 0 0 0 ok 2009-Mar-14 22:43:24 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:43:24 LOG3 to_alfamon: To ALFAMON: CAL HI 2009-Mar-14 22:43:24 LOG2 socket_wait: Starting sockwait on ALFAMON for 'command to ALFA' using string 'ACK' 2009-Mar-14 22:43:24 LOG3 socket_wait: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:43:24 START begin_task: Starting task 'waiting on command to ALFA' 2009-Mar-14 22:43:24 LOG5 begin_task: Level: (4) ID = <10161> Status = 0 0 0 0 ok 2009-Mar-14 22:43:24 LOG4 got_alfamon: From ALFAMON: ACK 2009-Mar-14 22:43:24 STOP end_task: Finishing task 'waiting on command to ALFA' with status 'OK' 2009-Mar-14 22:43:24 LOG5 end_task: Level: (4) ID = <10161> Status = 0 0 0 0 ok 2009-Mar-14 22:43:24 LOG3 socket_wait: DONE with sockwait on ALFAMON for 'command to ALFA' 2009-Mar-14 22:43:24 LOG3 to_alfamon: To ALFAMON: NOISE ACTIVE 2009-Mar-14 22:43:24 STOP end_task: Finishing task 'selecting calibration type' with status 'OK' 2009-Mar-14 22:43:24 LOG5 end_task: Level: (3) ID = <10158> Status = 0 0 0 0 ok 2009-Mar-14 22:43:24 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_cal_on MESSAGE {Setting CAL-ON ...} 2009-Mar-14 22:43:24 LOG3 wapp_calcontrol: To CALCONTROL: CALON 2009-Mar-14 22:43:24 LOG3 sock_errsend: To CALCONTROL: CALON STATUS 2009-Mar-14 22:43:24 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 22:43:24 LOG5 begin_task: Level: (3) ID = <10162> Status = 0 0 0 0 ok 2009-Mar-14 22:43:24 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 22:43:24 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x03 2009-Mar-14 22:43:24 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 22:43:24 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 22:43:24 LOG5 end_task: Level: (3) ID = <10162> Status = 0 0 0 0 ok 2009-Mar-14 22:43:24 LOG4 take_data: Calling 'take_data 1 1 CAL ON stat_cal_on {CAL-ON spectra}' 2009-Mar-14 22:43:24 START begin_task: Starting task 'WAPP spectral observation' 2009-Mar-14 22:43:24 LOG5 begin_task: Level: (3) ID = <10163> Status = 0 0 0 0 ok 2009-Mar-14 22:43:24 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for CAL-ON spectra ...} 2009-Mar-14 22:43:24 LOG5 log_alfabeam: Can't log alfabeam, not J2000 2009-Mar-14 22:43:24 INFO2 take_data: Starting WAPP 1-second scan: 907300180 2009-Mar-14 22:43:24 START begin_task: Starting task 'waiting on WAPP spectra' 2009-Mar-14 22:43:24 LOG5 begin_task: Level: (4) ID = <10164> Status = 0 0 0 0 ok 2009-Mar-14 22:43:24 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 22:43:24 LOG4 send_obs_status: To obs_status: <0> TASKTIME 1 BITMAP stat_cal_on MESSAGE {Taking CAL-ON spectra ...} 2009-Mar-14 22:43:24 INFO1 WAPP=1+2+3+4-start_spectra: start sec 9805.00 2009-Mar-14 22:43:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:43:26 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.000000 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 22:43:26 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:43:26 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:43:26 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 22:43:26 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 22:43:26 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:43:26 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:43:26 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:43:26 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:43:26 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 22:43:26 STOP end_task: Finishing task 'waiting on WAPP spectra' with status 'OK' 2009-Mar-14 22:43:26 LOG5 end_task: Level: (4) ID = <10164> Status = 0 0 0 0 ok 2009-Mar-14 22:43:26 STOP end_task: Finishing task 'WAPP spectral observation' with status 'OK' 2009-Mar-14 22:43:26 LOG5 end_task: Level: (3) ID = <10163> Status = 0 0 0 0 ok 2009-Mar-14 22:43:26 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_cal_off MESSAGE {Setting CAL-OFF ...} 2009-Mar-14 22:43:26 LOG3 wapp_calcontrol: To CALCONTROL: CALOFF 2009-Mar-14 22:43:26 LOG3 sock_errsend: To CALCONTROL: CALOFF STATUS 2009-Mar-14 22:43:26 START begin_task: Starting task 'waiting on CALCONTROL command' 2009-Mar-14 22:43:26 LOG5 begin_task: Level: (3) ID = <10165> Status = 0 0 0 0 ok 2009-Mar-14 22:43:26 LOG3 CALCONTROL-caltrig: Software trigger 2009-Mar-14 22:43:26 LOG1 CALCONTROL-caltrig: Cal/trigger control status 0x02 2009-Mar-14 22:43:26 LOG3 got_calcontrol: Received status OK from CALCONTROL 2009-Mar-14 22:43:26 STOP end_task: Finishing task 'waiting on CALCONTROL command' with status 'OK' 2009-Mar-14 22:43:26 LOG5 end_task: Level: (3) ID = <10165> Status = 0 0 0 0 ok 2009-Mar-14 22:43:26 LOG4 send_obs_status: To obs_status: <0> BITMAP stat_busy 2009-Mar-14 22:43:26 STOP finish_task: Finishing task 'WAPP calibration' 2009-Mar-14 22:43:26 LOG5 finish_task: Level: (2) ID = <10157> Status = 0 0 0 0 ok 2009-Mar-14 22:43:26 INFO2 finish_task: DONE finished calibration: WAPP calibration 2009-Mar-14 22:43:26 LOG4 send_obs_status: To obs_status: <0> ENDTASK Finished 2009-Mar-14 22:43:26 STOP end_task: Finishing task 'WAPP calibration' with status 'OK' 2009-Mar-14 22:43:26 LOG5 end_task: Level: (2) ID = <10157> Status = 0 0 0 0 ok 2009-Mar-14 22:43:26 INFO2 fixed_driftmap: Starting fixed azimuth drift map loop 5 of 99 2009-Mar-14 22:43:26 LOG4 send_obs_status: To obs_status: <1> LOOP 5 2009-Mar-14 22:43:26 LOG3 send_to_one_wapp: To WAPPCON: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:43:26 LOG3 send_to_one_wapp: To WAPPCON2: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:43:26 LOG3 send_to_one_wapp: To WAPPCON3: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:43:26 LOG3 send_to_one_wapp: To WAPPCON4: PROJECT a2010 Lyle Hoffman 2009-Mar-14 22:43:27 LOG4 send_obs_status: To obs_status: <1> INFO {Making drift scan followed by CAL} 2009-Mar-14 22:43:27 LOG4 take_data: Calling 'take_data 600 1 FIXEDAZ FIXEDAZ stat_drift {drift scan}' 2009-Mar-14 22:43:27 START begin_task: Starting task 'WAPP spectral observation' 2009-Mar-14 22:43:27 LOG5 begin_task: Level: (2) ID = <10166> Status = 0 0 0 0 ok 2009-Mar-14 22:43:27 LOG4 send_obs_status: To obs_status: <0> TASKWAIT BITMAP stat_busy MESSAGE {Waiting for drift scan ...} 2009-Mar-14 22:43:27 LOG5 log_alfabeam: Can't log alfabeam, not J2000 2009-Mar-14 22:43:27 INFO2 take_data: Starting WAPP 600-second scan: 907300181 2009-Mar-14 22:43:27 START begin_task: Starting task 'waiting on WAPP spectra' 2009-Mar-14 22:43:27 LOG5 begin_task: Level: (3) ID = <10167> Status = 0 0 0 0 ok 2009-Mar-14 22:43:27 LOG4 WAPP=1+2+3+4-wappcon: Received command 'PROJECT a2010 Lyle Hoffman' 2009-Mar-14 22:43:27 LOG4 WAPP=1+2+3+4-wappcon: Received a FITS-header block 2009-Mar-14 22:43:27 LOG4 send_obs_status: To obs_status: <0> TASKTIME 600 BITMAP stat_drift MESSAGE {Taking drift scan ...} 2009-Mar-14 22:43:27 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.557 (still bad) 2009-Mar-14 22:43:27 INFO1 WAPP=1+2+3+4-start_spectra: start sec 9808.00 2009-Mar-14 22:43:27 NOTE WAPPDATA-new_file: New FITS file: wapp.20090314.a2010.0034.fits 2009-Mar-14 22:43:27 LOG4 send_obs_status: To obs_status: <0> FILENAME {wapp.20090314.a2010.0034.fits} 2009-Mar-14 22:43:29 LOG3 WAPP=1+2+3+4-save_rfcalc: Up: 1635.000000 MHz --- rfnum = 17 ifnum = 6 inpfrq = 4 2009-Mar-14 22:43:29 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 1: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:43:29 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 2: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 997.770299 MHz 2009-Mar-14 22:43:29 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 3: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 944.605146 MHz 2009-Mar-14 22:43:29 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 4: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 942.648154 MHz 2009-Mar-14 22:43:29 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 5: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:43:29 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 6: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:43:29 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 7: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:43:29 LOG3 WAPP=1+2+3+4-save_rfcalc: Channel 8: Sky freq = 1385.000000 MHz Flip = 1 Band = 0 Mixer = 1750.000000 MHz 2009-Mar-14 22:43:29 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:43:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:43:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:43:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:43:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:43:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:43:41 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:43:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:43:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:43:47 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.111 (still bad) 2009-Mar-14 22:43:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:43:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:43:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:43:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:43:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:43:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:44:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:44:04 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:44:04 LOG4 check_wapp_levels: WAPP-1 power levels: 0.916 0.924 1.049 1.056 2009-Mar-14 22:44:04 LOG4 check_wapp_levels: WAPP-2 power levels: 1.028 0.970 1.115 0.896 2009-Mar-14 22:44:04 LOG4 check_wapp_levels: WAPP-3 power levels: 0.898 0.984 1.024 0.917 2009-Mar-14 22:44:04 LOG4 check_wapp_levels: WAPP-4 power levels: 0.936 0.109 1.033 0.119 2009-Mar-14 22:44:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.122 (still bad) 2009-Mar-14 22:44:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.125 (still bad) 2009-Mar-14 22:44:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.128 (still bad) 2009-Mar-14 22:44:12 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.131 (still bad) 2009-Mar-14 22:44:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.130 (still bad) 2009-Mar-14 22:44:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.126 (still bad) 2009-Mar-14 22:44:18 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.125 (still bad) 2009-Mar-14 22:44:20 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.118 (still bad) 2009-Mar-14 22:44:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:44:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.120 (still bad) 2009-Mar-14 22:44:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.124 (still bad) 2009-Mar-14 22:44:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.129 (still bad) 2009-Mar-14 22:44:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.138 (still bad) 2009-Mar-14 22:44:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.134 (still bad) 2009-Mar-14 22:44:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.130 (still bad) 2009-Mar-14 22:44:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.128 (still bad) 2009-Mar-14 22:44:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.121 (still bad) 2009-Mar-14 22:44:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.115 (still bad) 2009-Mar-14 22:44:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:44:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:44:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:44:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:44:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:44:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:44:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:44:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:44:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:45:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:06 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:45:06 LOG4 check_wapp_levels: WAPP-1 power levels: 0.918 0.924 1.049 1.057 2009-Mar-14 22:45:06 LOG4 check_wapp_levels: WAPP-2 power levels: 1.036 0.978 1.109 0.892 2009-Mar-14 22:45:06 LOG4 check_wapp_levels: WAPP-3 power levels: 0.902 0.988 1.025 0.921 2009-Mar-14 22:45:06 LOG4 check_wapp_levels: WAPP-4 power levels: 0.935 0.109 1.032 0.119 2009-Mar-14 22:45:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:45:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:45:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:45:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:45:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:45:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:45:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:45:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:45:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:45:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:45:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:45:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:45:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:45:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:45:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:46:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:46:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:46:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:46:07 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:46:07 LOG4 check_wapp_levels: WAPP-1 power levels: 0.919 0.924 1.048 1.056 2009-Mar-14 22:46:07 LOG4 check_wapp_levels: WAPP-2 power levels: 1.026 0.967 1.110 0.901 2009-Mar-14 22:46:07 LOG4 check_wapp_levels: WAPP-3 power levels: 0.895 0.980 1.022 0.918 2009-Mar-14 22:46:07 LOG4 check_wapp_levels: WAPP-4 power levels: 0.936 0.109 1.032 0.119 2009-Mar-14 22:46:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:46:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:46:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:46:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:46:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:46:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:46:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:46:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:46:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:46:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:46:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:46:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:46:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:46:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:46:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:46:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:46:41 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:46:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:46:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:46:47 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.109 (still bad) 2009-Mar-14 22:46:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:46:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:46:54 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:46:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:46:58 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.109 (still bad) 2009-Mar-14 22:47:00 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.109 (still bad) 2009-Mar-14 22:47:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:47:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:47:06 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.116 (still bad) 2009-Mar-14 22:47:08 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:47:08 LOG4 check_wapp_levels: WAPP-1 power levels: 0.920 0.923 1.048 1.056 2009-Mar-14 22:47:08 LOG4 check_wapp_levels: WAPP-2 power levels: 1.025 0.962 1.113 0.900 2009-Mar-14 22:47:08 LOG4 check_wapp_levels: WAPP-3 power levels: 0.894 0.978 1.021 0.918 2009-Mar-14 22:47:08 LOG4 check_wapp_levels: WAPP-4 power levels: 0.935 0.109 1.033 0.119 2009-Mar-14 22:47:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:47:12 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:47:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:47:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:47:18 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.117 (still bad) 2009-Mar-14 22:47:20 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.112 (still bad) 2009-Mar-14 22:47:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:47:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:47:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:47:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:47:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:47:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:47:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:47:36 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.108 (still bad) 2009-Mar-14 22:47:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:47:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:47:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:47:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:47:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:47:47 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:47:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:47:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:47:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:47:54 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:47:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:47:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:48:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:48:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:48:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:48:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:48:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:48:10 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:48:10 LOG4 check_wapp_levels: WAPP-1 power levels: 0.919 0.922 1.046 1.056 2009-Mar-14 22:48:10 LOG4 check_wapp_levels: WAPP-2 power levels: 1.023 0.958 1.108 0.903 2009-Mar-14 22:48:10 LOG4 check_wapp_levels: WAPP-3 power levels: 0.891 0.974 1.024 0.916 2009-Mar-14 22:48:10 LOG4 check_wapp_levels: WAPP-4 power levels: 0.934 0.109 1.031 0.118 2009-Mar-14 22:48:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:48:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:48:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:48:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:48:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:48:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:48:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:48:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:48:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:48:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:48:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:48:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:48:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:48:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:48:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:48:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:48:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:48:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:48:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:48:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:48:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:48:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:48:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:48:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:49:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:49:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:49:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:49:11 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:49:11 LOG4 check_wapp_levels: WAPP-1 power levels: 0.920 0.923 1.046 1.053 2009-Mar-14 22:49:11 LOG4 check_wapp_levels: WAPP-2 power levels: 1.023 0.960 1.105 0.905 2009-Mar-14 22:49:11 LOG4 check_wapp_levels: WAPP-3 power levels: 0.891 0.971 1.023 0.915 2009-Mar-14 22:49:11 LOG4 check_wapp_levels: WAPP-4 power levels: 0.934 0.109 1.032 0.119 2009-Mar-14 22:49:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:49:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:49:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:49:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:49:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:49:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:49:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:49:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:49:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:49:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:49:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:49:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:50:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:50:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:50:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:50:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:50:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:50:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:50:12 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:50:12 LOG4 check_wapp_levels: WAPP-1 power levels: 0.921 0.923 1.048 1.054 2009-Mar-14 22:50:12 LOG4 check_wapp_levels: WAPP-2 power levels: 1.024 0.961 1.108 0.909 2009-Mar-14 22:50:12 LOG4 check_wapp_levels: WAPP-3 power levels: 0.890 0.974 1.021 0.916 2009-Mar-14 22:50:12 LOG4 check_wapp_levels: WAPP-4 power levels: 0.936 0.109 1.033 0.119 2009-Mar-14 22:50:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:50:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:50:18 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:50:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:50:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:50:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:50:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:50:28 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:50:30 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:50:32 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:50:34 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:50:36 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:50:38 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:50:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:50:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:50:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:50:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:50:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:50:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:50:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:50:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:50:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:50:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:51:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:51:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.103 (still bad) 2009-Mar-14 22:51:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:51:06 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:51:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:51:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:51:12 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:51:14 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:51:15 LOG4 check_wapp_levels: WAPP-1 power levels: 0.922 0.921 1.049 1.053 2009-Mar-14 22:51:15 LOG4 check_wapp_levels: WAPP-2 power levels: 1.022 0.962 1.106 0.902 2009-Mar-14 22:51:15 LOG4 check_wapp_levels: WAPP-3 power levels: 0.889 0.971 1.020 0.915 2009-Mar-14 22:51:15 LOG4 check_wapp_levels: WAPP-4 power levels: 0.934 0.109 1.031 0.119 2009-Mar-14 22:51:17 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:51:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:51:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:51:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:51:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.104 (still bad) 2009-Mar-14 22:51:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:51:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:51:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:51:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:51:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:51:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:51:39 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:51:41 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:51:43 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:51:45 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:51:47 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:51:49 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:51:51 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:51:53 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:51:55 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.117 (still bad) 2009-Mar-14 22:51:57 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.116 (still bad) 2009-Mar-14 22:51:59 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.119 (still bad) 2009-Mar-14 22:52:01 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.119 (still bad) 2009-Mar-14 22:52:03 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.119 (still bad) 2009-Mar-14 22:52:05 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.119 (still bad) 2009-Mar-14 22:52:06 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 14 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:52:07 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.117 (still bad) 2009-Mar-14 22:52:09 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:52:11 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.112 (still bad) 2009-Mar-14 22:52:13 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:52:15 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:52:17 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.109 < 0.75)! 2009-Mar-14 22:52:17 LOG4 check_wapp_levels: WAPP-1 power levels: 0.922 0.926 1.054 1.057 2009-Mar-14 22:52:17 LOG4 check_wapp_levels: WAPP-2 power levels: 1.022 0.961 1.108 0.905 2009-Mar-14 22:52:17 LOG4 check_wapp_levels: WAPP-3 power levels: 0.896 0.978 1.023 0.919 2009-Mar-14 22:52:17 LOG4 check_wapp_levels: WAPP-4 power levels: 0.937 0.109 1.036 0.119 2009-Mar-14 22:52:19 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:52:21 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.108 (still bad) 2009-Mar-14 22:52:23 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:52:25 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:52:27 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:52:29 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.114 (still bad) 2009-Mar-14 22:52:31 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:52:33 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:52:35 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:52:37 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:52:40 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:52:42 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:52:44 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:52:46 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:52:48 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:52:50 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:52:52 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:52:54 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:52:56 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:52:58 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.105 (still bad) 2009-Mar-14 22:53:00 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:53:02 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:53:04 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:53:05 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:53:06 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.114 (still bad) 2009-Mar-14 22:53:08 LOG3 WAPP=4-chip_count: Counts don't match between chip 0 and chip 12 (99999966 != 99999964 diff = 2)! 2009-Mar-14 22:53:08 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:53:10 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.113 (still bad) 2009-Mar-14 22:53:12 INFO5 check_wapp_levels: WAPP power levels are between 0.110 and 1.113 (still bad) 2009-Mar-14 22:53:14 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.111 (still bad) 2009-Mar-14 22:53:16 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.110 (still bad) 2009-Mar-14 22:53:18 WARNING check_wapp_levels: WARNING there are WAPP channels with too little power (0.110 < 0.75)! 2009-Mar-14 22:53:18 LOG4 check_wapp_levels: WAPP-1 power levels: 0.927 0.927 1.051 1.058 2009-Mar-14 22:53:18 LOG4 check_wapp_levels: WAPP-2 power levels: 1.027 0.966 1.114 0.904 2009-Mar-14 22:53:18 LOG4 check_wapp_levels: WAPP-3 power levels: 0.891 0.975 1.028 0.925 2009-Mar-14 22:53:18 LOG4 check_wapp_levels: WAPP-4 power levels: 0.939 0.110 1.038 0.119 2009-Mar-14 22:53:20 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:53:22 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.109 (still bad) 2009-Mar-14 22:53:24 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.107 (still bad) 2009-Mar-14 22:53:26 INFO5 check_wapp_levels: WAPP power levels are between 0.109 and 1.106 (still bad) 2009-Mar-14 22:53:28 INFO1 WAPP=1+2+3+4-start_spectra: DONE with spectral line observation 2009-Mar-14 22:53:28 STOP end_task: Finishing task 'waiting on WAPP spectra' with status 'OK' 2009-Mar-14 22:53:28 LOG5 end_task: Level: (3) ID = <10167> Status = 0 0 0 0 ok 2009-Mar-14 22:53:28 STOP end_task: Finishing task 'WAPP spectral observation' with status 'OK' 2009-Mar-14 22:53:28 LOG5 end_task: Level: (2) ID = <10166> Status = 0 0 0 0 ok 2009-Mar-14 22:53:28 LOG1 fixed_driftmap: New position: year = 2009.2024744594014 RA = 09:57:18.7 RA/Dec = 09:57:51.8 +21:51:15.0 2009-Mar-14 22:53:28 NOTE fixed_driftmap: Correcting ZA to 3:30:01.3 ... 2009-Mar-14 22:53:28 LOG3 vw_send: To DATATAKING: pnt tr -UD 180.0 3.5003561082 -CF 2009-Mar-14 22:53:28 LOG2 take_cal: Calling 'take_cal hcorcal 1 1' 2009-Mar-14 22:53:28 START begin_task: Starting task 'WAPP calibration' 2009-Mar-14 22:53:28 LOG5 begin_task: Level: (2) ID = <10168> Status = 0 0 0 0 ok 2009-Mar-14 22:53:28 LOG4 send_obs_status: To obs_status: <0> NEWTASK {WAPP Calibration} INFO {Making WAPP calibration ...} 200